Too much plow?

[porkchop401]

Porkchop,

Is this a "one and done" job, or will you need to do more of this virgin ground breaking?

How big is the area you're breaking?

If it isn't a huge field, and this is only needing to be done once, how about using a middle buster to break the ground, followed by the plow?

Are you then going to disc the whole thing again?

How about a 3 pt tiller?

I intend to grow veggies for market once I retire in the years to come, as for now I am breaking this ground that was cleared about 5 years ago and I have been bus hogging ever since.
I intend t start adding organic matter such as cotton trash and chicken litter to get it ready to grow so I am thinking follow up plowing will be easier. As for as a tiller I am still dealing with a few stumps hat have not rotted out.

 

[porkchop401]

I am definitely going to upgrade my tractor but I do not want to go so large that my current implements are useless.

 

[porkchop401]

Your Yanmar weighs about 2000 pounds? I am surprised it is having problems. Maybe dropping down a gear would help? I like plowing so for me, the slower I go the more time I have to watch the action behind me.

My avatar is a Deere 2305 pulling a Brinly 12" plow.

Ok I have to admit the thought of a 18" plow had me scratching my head so I googled the 18" Pittsburg mould board plow and it is a fraction of the plow Iam pulling. Mine is a howse for a full size tractor.

 

[K5lwq]

I am definitely going to upgrade my tractor but I do not want to go so large that my current implements are useless. View attachment 718713

You are making progress. Hit that with a disk a couple of times in the same direction then cross ways. Then use your plow again and you will have better results.

But I agree upgrading your tractor will be beneficial.

 

[toolslinger]

Honestly, you look like you're doing a nice job as is. Hitting roots, big rocks, or stumps is going to be an issue on most machines I would think, especially in first break. We've been running in to buried rocks, and dead stopping our 8N since before I was alive. Doesn't seem to care much. Yea, we could run the backhoe out to get at them, but up where we are, that rock is just as likely to be the size of a truck...
Once you're looking at utility machines in the mid 30 hp range, you should just look at the mid 40's as well. They're not much bigger if any, and still run the Cat 1 gear without issue. My MF 135 is pretty much the same size as our 8N, and while heavier, isn't really that much bigger than your current ride. Figure like 8-12" bigger in each direction, and almost twice the ponies...

 

[DJ54]

That dirt looks pretty dry, so that plow is going to pull harder. By stalling, I'm assuming you're meaning spinning. Are your tires loaded..?? Because I see no wheel weights, and unless my eyes are deceiving me, the furrow tire looks to be on backwards. That's not helping either.

 

[bigtiller]

Ok I have to admit the thought of a 18" plow had me scratching my head so I googled the 18" Pittsburg mould board plow and it is a fraction of the plow Iam pulling. Mine is a howse for a full size tractor.

I'm gonna have to google that to see what you're talking about, or was it a typo?

 

[ROUSTABOUT]

I'm gonna have to google that to see what you're talking about, or was it a typo?

Last I broke a field with a four bottom plow with trips.

 

[porkchop401]

That dirt looks pretty dry, so that plow is going to pull harder. By stalling, I'm assuming you're meaning spinning. Are your tires loaded..?? Because I see no wheel weights, and unless my eyes are deceiving me, the furrow tire looks to be on backwards. That's not helping either.

You are correct in that my tires are not loaded and it is dry and I am spinning when I stall. My tires are running in the correct direction I am going to water the rear tires before I break ground and add front weight since I'm light on the front when the plow is in the ground.

 

[porkchop401]

I'm gonna have to google that to see what you're talking about, or was it a typo?

That plow is measured from the frame to plow point.rather than from rear tip of the shear across to the rail. Resulting In the width of turned ground per plow.