Rounded off drain plug
- Thread starter Kando
- Start date
- Views: 298877
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 7,590
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
When a new Pope is elected, they send up white smoke. When the drain plug comes out, I think Kando should tip up some pallets in his field.
dragoneggs
Super Star Member
- Joined
- Jun 9, 2013
- Messages
- 14,548
- Location
- Seabeck, Washington
- Tractor
- Kubota BX-25D, Kubota Z122RKW-42
:thumbsup::thumbsup:
hawkeye08
Elite Member
Boats were mentioned above, the boat we had was equipped with a fitting in place of oil plug that had a small pipe attached to it that went up beside the engine. It had a cap on it that was removed when it was time to change the oil, just sucked it right out, pulling from the normal drain in pan, so it got everything out that pulling the plug would have.. of course there are many different systems in place.
goeduck
Super Star Member
I think some time back I wondered if this thread would get to 2000 posts before we figured it out. So we have time. I bet it will be some hairbrained idea that wins the prize.
k0ua
Epic Contributor
Like go to town and get a replacement drain plug, hit the old one with a propane torch after wipedown, and then put a pipe wrench of suitable size on it and turn the correct direction to back the plug out and be done with it?
Something like that?
Big Barn
Super Member
- Joined
- Aug 20, 2013
- Messages
- 7,047
- Location
- Victoria, B C
- Tractor
- More than 40 over the years. Ten at any one time. Mostly Ford and New Holland
Like go to town and get a replacement drain plug, hit the old one with a propane torch after wipedown, and then put a pipe wrench of suitable size on it and turn the correct direction to back the plug out and be done with it?
I agree. With heat applied to the plug grip would not be as critical.
goeduck
Super Star Member
I am not sure, Kandos plug is different than anything TBN has dealt with before, it is not an ordinary pallet,,,,, uhhh, I mean... plug. :duh: :duh:Like go to town and get a replacement drain plug, hit the old one with a propane torch after wipedown, and then put a pipe wrench of suitable size on it and turn the correct direction to back the plug out and be done with it?
/pine
Super Star Member
- Joined
- Mar 4, 2009
- Messages
- 15,763
Why does idiocy abound? and why do some folks see forum queries as contests?...it ceases to amuse me...
Big Barn
Super Member
- Joined
- Aug 20, 2013
- Messages
- 7,047
- Location
- Victoria, B C
- Tractor
- More than 40 over the years. Ten at any one time. Mostly Ford and New Holland
Are you saying it amused you at one time, but no longer????
goeduck
Super Star Member
Sorry /pine you will need to amuse yourself. :wave:
Why do you keep reading them if you find them so offensive? To me that's the biggest mystery of all.
/pine
Super Star Member
- Joined
- Mar 4, 2009
- Messages
- 15,763
What I said was a (paraphrased) sublimated expression that should have read "never ceases to amuse me"...
/pine
Super Star Member
- Joined
- Mar 4, 2009
- Messages
- 15,763
Hate to detract from the topic but I'm curious why some folks like to play "hall monitor"...especially when they cant see the enigma for the mystery...LoL...
bigtiller
Super Member
- Joined
- Feb 1, 2006
- Messages
- 7,323
- Location
- central Iowa
- Tractor
- John Deere 2720 John Deere 3039R John Deere Z545R
dragoneggs
Super Star Member
- Joined
- Jun 9, 2013
- Messages
- 14,548
- Location
- Seabeck, Washington
- Tractor
- Kubota BX-25D, Kubota Z122RKW-42
Okay another hair brained idea since you are betting...
1. Drill a hole through the side of the plug.
2. Drive a hard pin through the plug that extends a bit on both ends.
3. Grind a couple of notches in a socket that fit the pin.
4. Put a ratchet and cheater bar on it.
5. Break the socket.
Oh well... next?
goeduck
Super Star Member
Thank you for your contributions to the post count. Much appreciated :thumbsup:
If you can think of a way to get the plug out, please chime in. :thumbsup:
k0ua
Epic Contributor
Impact socket might not break?
