k0ua
Epic Contributor
I might use my leather punch to make the hole. This would probably work, but I still would rather sew it with some good thread.
Ratchet strap ends
- Thread starter JJZ 109
- Start date
- Views: 6499
I might use my leather punch to make the hole. This would probably work, but I still would rather sew it with some good thread.
Diamondpilot
Super Star Member
- Joined
- Jan 18, 2007
- Messages
- 16,316
- Location
- Daleville, IN
- Tractor
- Jinma 254/284 Ford 861 Powermaster at work
Not worth messing with. You can get new 2" straps any day of the week for $10 each.
Chris
Chris
JPRambo
Platinum Member
I have a old (1975) CONSEW machine and have sewn a few straps and strap protector loops. 2 pieces of 4" straps sewn together and slide over 2 inch to protect from sharp edges. Works well.
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 57,934
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
k0ua
Epic Contributor
Sometimes it is kinda fun and fulfilling to repair thing's. If it don't take a long time or cost much to repair, I enjoy repairing things.
You can buy replacement straps and keep your ratcheting mechanism. I wouldn't trust a sewing job unless you were sure it was done properly to hold the load.
They sell all kinds of straps ones with flat hooks, j hooks, chain ends, etc.
I have a few endless ratchets that are really handy. They have the long strap attached to the ratchet and you just feed it through and use it for holding bundles of things together.
They sell all kinds of straps ones with flat hooks, j hooks, chain ends, etc.
I have a few endless ratchets that are really handy. They have the long strap attached to the ratchet and you just feed it through and use it for holding bundles of things together.
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 57,934
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
Oh I understand that. I've got several garages full of things I'm going to repair some day.
However, self-sewing a ratchet strap, I just don't know. Sure, you could do it. What strength thread would you use? How would you know the repair is gonna hold the load? If your load falls off your trailer and kills you, will your insurance void its coverage? Etc.... It's just one of those things I probably wouldn't attempt a repair on since the cost of new is so darn low. I'd keep the mechanism if its in good shape, and use the old strap for firewood log duty until it got too abraded. Or a tire swing. 
newbury
Super Star Member
- Joined
- Jan 8, 2009
- Messages
- 14,096
- Location
- From Vt, in Va, retiring to MS
- Tractor
- Kubota's - B7610, M4700
Oh I understand that. I've got several garages full of things I'm going to repair some day.
What Moss wrote.
If the strap is so worn that the hook came off I'd be hesitant to trust it throughout. Just tie a knot and regard it as a degraded, worn strap.
von-mil
Gold Member
If you go the re-stitch route, be sure to use UV-resistant thread and lots of it. The looped/stitched ends of my ratchet straps have about six inches of back-and-forth zig-zags, plus a 6x2 inch rectangular box stitched in with a big "X" stitched inside of that.
A cobbler or a tent or zipper repair shop can do the work but it might cost more than a new set of ratchet straps.
A cobbler or a tent or zipper repair shop can do the work but it might cost more than a new set of ratchet straps.
OP
JJZ 109
Veteran Member
- Joined
- Feb 7, 2009
- Messages
- 2,175
- Location
- Lake Ontario/St. Lawrence River
- Tractor
- Kubota BX2380/LA344 loader/60" MMM, Bobcat S185 skid steer, JD X394 4 wheel steer mower
Which I pointed out. I just thought if there was a low cost way to save them I'd explore it instead of tossing a serviceable strap. It's not looking too promising for that. I thought that maybe someone made a replacement hook with a couple of slots to feed the strap through, kinda like an adjustable camera or helmet strap.
My seasonal business is about ready to reopen. You can bet that I won't be taking the time to sew, rivet, glue or any other similar method to save them. I don't really even need them. Just didn't want to be wasteful.
