OP
Poor man's side by side
- Thread starter NS Gearhead
- Start date
- Views: 87447
slowzuki
Elite Member
- Joined
- Sep 19, 2003
- Messages
- 4,156
- Location
- New Brunswick, Canada
- Tractor
- Kubota L5030 HSTC, MF 5455, Kubota M120, Allis Chalmers 7010
Looks a lot like the welding I did on my "plow tracker" also added a cement block rack in the rear so we could fill the rear all the way up.
Green Power
Veteran Member
- Joined
- Dec 1, 2013
- Messages
- 1,077
- Location
- Nebraska
- Tractor
- LS R4047H, Kubota L33400 JD: 5075E 6150M 9230 and 8520
Nice side by side NS! I didnt know you could buy turf tires that size.:laughing: Keep up the great work!
rd_macgregor
Veteran Member
- Joined
- May 14, 2008
- Messages
- 1,875
- Location
- Prince Edward Island, Canada
- Tractor
- Kioti DK45SC, Kubota B2650
I think you'll get lots better traction, but the tires will be seriously susceptible to flats. With such thin rubber in the grooves, any stick or sharp rock out there is a puncture, or rupture, waiting to happen.
OP
NS Gearhead
Veteran Member
That may be, but they were toast anyway... and I won't be going any farther then a km away from my house. I can always carry an air pig, plugs, and jack.
I'm in with a couple of the local offroad shops... I may put feelers out for a set of used mud terrains.
I'm in with a couple of the local offroad shops... I may put feelers out for a set of used mud terrains.
OP
NS Gearhead
Veteran Member
Started on the rear body... starting with a piece of 2x2X1/8 all the way across the back tapered 45deg on the ends with some 6X1/8" flat plate on that
Cut out the rust
... and spent some time filling in what was missing
Cut out the rust
... and spent some time filling in what was missing
Xfaxman
Super Star Member
- Joined
- Feb 8, 2013
- Messages
- 13,291
- Location
- Guthrie, OK
- Tractor
- Toolcat 5610 G - Bobcat V417 - TORO+Loader
:thumbsup:
OP
NS Gearhead
Veteran Member
AaronS
Platinum Member
- Joined
- May 3, 2008
- Messages
- 673
- Location
- Santa Claus, Indiana
- Tractor
- LS XR4046HC, New Holland Boomer 1020
I'll second the thumbs-up. I'm enjoying following your progress even though I haven't posted on your thread previously.
OP
NS Gearhead
Veteran Member
Thanks AaronS!
Got two hours to pick away at my "practice" project. LOL
Capped the ends and preped the plates
Burned the plates to the square tube (after test fitting and tacking)
Re-installed
First piece in... I think I realy got it in the upper middle. A5 on the mig, overlaping spot welds. Their's a fraction of a second between spot welds that I can see the seam.
Cleaned up
Next piece
...and last. Don't look at the giant blob of shameful weld in the corner. LOL
Got two hours to pick away at my "practice" project. LOL
Capped the ends and preped the plates
Burned the plates to the square tube (after test fitting and tacking)
Re-installed
First piece in... I think I realy got it in the upper middle. A5 on the mig, overlaping spot welds. Their's a fraction of a second between spot welds that I can see the seam.
Cleaned up
Next piece
...and last. Don't look at the giant blob of shameful weld in the corner. LOL
