New JD450c owner

[DrHolliday]

I am trying to put a JD450C back to working that has not been cranked in eight years, I have it running but it will not move, everything else works.

Hope to make it work without too much money.

DrHolliday

 

[kensnelling]

Welcome from Oklahoma. Good luck with your project.

Ken

 

[mguitas]

:welcome:

 

[creekbend]

Welcome aboard. Best wishes.

 

[The kid]

Welcome Doc to TBN. A tractor is good medicine to get away from the rat race.

 

[Briana03]

Welcome to TBN

I moved your thread to the Construction Equipment forum.

 

[Bob Rooks]

When you say "it will not move" what do you mean?
Does the engine lug down when you try to move it, but it won't move?
Does the engine not change speed when you try to move it?
Is it a manual transmission or a power-shift?
Oil in torque converter?
How old is the machine?

Btw, :welcome:

 

[JasG]

When you say "it will not move" what do you mean?
Does the engine lug down when you try to move it, but it won't move?
Does the engine not change speed when you try to move it?
Is it a manual transmission or a power-shift?
Oil in torque converter?
How old is the machine?

I don't think the 450C model was made with a powershift. I believe they only had a manual 4 speed with hydraulic reverser. The C's were made from about 1973-83.

 

[DrHolliday]

Welcome to TBN

I moved your thread to the Construction Equipment forum.

THANKS, I AM NEW TO THIS THREAD THING.

 

[DrHolliday]

Thanks Bob for the reply, I was pushing some dirt, with all systems go, then it stopped moving forward or reverce. I just ordered a OM from JD will have it Friday. Engine runs great and all other systems work. I did notice that a lot of fluid had leaked from around the left back finial drive.
Before I do anymore I will wait for the Manual. I think it is a 1979.
Thanks for any info.
DR

 

[Bob Rooks]

Thanks Bob for the reply, I was pushing some dirt, with all systems go, then it stopped moving forward or reverce. I just ordered a OM from JD will have it Friday. Engine runs great and all other systems work. I did notice that a lot of fluid had leaked from around the left back finial drive.
Before I do anymore I will wait for the Manual. I think it is a 1979.
Thanks for any info.
DR

It's obviously something that affects both tracks then. Check all oil levels.

 

[JasG]

Thanks Bob for the reply, I was pushing some dirt, with all systems go, then it stopped moving forward or reverce. I just ordered a OM from JD will have it Friday. Engine runs great and all other systems work. I did notice that a lot of fluid had leaked from around the left back finial drive.
Before I do anymore I will wait for the Manual. I think it is a 1979.
Thanks for any info.
DR

Do you have any feeling when pushing in the clutch? The main things common to both sides would be the engine clutch I wonder if something there let loose.

The high low reverse clutch is hydraulic, its possible the valve went bad or something in that system.

It could also be the transmission itself.

It's been a long time for me since I looked at one of these up close.

 

[JasG]

One more note:

If you go to Deere.com under parts you can look up parts with drawings of the assembly. I have found it very helpful in seeing how something goes together and/or help trouble shooting.


John Deere - Parts Catalog

 

[charlz]

I would try the forums at jdcrawlers.com, active board with lots of info.

 

[jagyzf]

I am trying to put a JD450C back to working that has not been cranked in eight years, I have it running but it will not move, everything else works.

Hope to make it work without too much money.

DrHolliday

Did you ever find the issue?

 

[pinevalley]

I was a JD mechanic for many years. Does the left pedal (engine clutch) have the fell similar to a car clutch? If so, make sure you have enough transmission oil(checked running)/ under seat dipstick. If above are of, you kind of have to put some pressure guages in it to see if you have transmission pump pressure.