How much trailer will I need?

[AWSubie]

Here's my NX5010 on my 20' trailer. If you are going to buy a trailer, I would not go any shorter than 20'. If you are renting and choices are limited you could get buy with 18' but space for adjusting tongue weight will be limited.

 

[4570Man]

This is a 24” trailer but it’s not very often I’d want to haul 2 loose implements and a bush hog on the back. Even if you did want to do that you could put the loader over the top of them. I’ve hauled the same tractor on a 16’ trailer. With the bucket sitting flat on the deck the bush hog sticks off the back and if I’m using the box blade instead it fits on with a foot to spare. If you’ve got a flat bed truck sitting the cutter in it would be fine but it’s not a good plan for a regular bed truck. I like having a trailer light enough to move the hitch by hand. It makes hooking it up much easier. My 5500 pound pintle hook trailer definitely doesn’t fit the bill.

 

[SloppyJoe]

You all have convinced me. A twenty foot trailer is a minimum!

 

[MinnesotaEric]

Planning the collection of my Kioti 4010 this week. It has a FEL, Backhoe and 60" rotary cutter. I figure I can use the loader to put the cutter in the bed of the truck, but how long of a trailer will I need for the tractor and backhoe? Images of something loaded with trailer lengths would be very helpful. I can rent an 18' equipment trailer, but don't own one yet.

Thanks

Get a 24' trailer. I regret purchasing a 20' trailer.

 

[biggziff]

Get a 24' trailer. I regret purchasing a 20' trailer.

Sell me your 20'

 

[George2615]

When I upgraded to a larger tractor I sold my 7K 20' tilt bed and bought a 14K 22' PJ tilt bed. Actual deck length including the knife edge is 23' and it gives me plenty of room to adjust the load fore and aft for better balance no matter what 3 pt. attachment I have on at the time. Go for the longer trailer.

 

[biggziff]

When I upgraded to a larger tractor I sold my 7K 20' tilt bed and bought a 14K 22' PJ tilt bed. Actual deck length including the knife edge is 23' and it gives me plenty of room to adjust the load fore and aft for better balance no matter what 3 pt. attachment I have on at the time. Go for the longer trailer.

You're close by me (I'm near Binghamton) Do you find the tilt bed more useful/safer than a dovetail or ramps?

Mind if I ask what you paid and where you bought it?

 

[kmmn]

I hauled a lot of all different kinds of equipment for years and I'll tell you I bought to small to begin with. 18ft isn't enough.. I found a 20 footer to be of much more use. What are you towing it with? Trailers are like buildings, you never seem to have enough room..

Exactly... pick your size and then add 2 feet. It won't make a difference to the tow vehicle, but it let's you move the equipment around to balance the weight front to back better.

 

[George2615]

You're close by me (I'm near Binghamton) Do you find the tilt bed more useful/safer than a dovetail or ramps?

Mind if I ask what you paid and where you bought it?

My current and last trailer were tilt beds. Non tilt are much cheaper. I went with tilt beds because of a shoulder injury and could no longer lift ramps by hand. Since I bought my first tilt bed I'll never go back to a non tilt even without any injuries. So much easier and faster to load vehicles. I bought my PJ down toward you in Cortland. The dealer is just off 81 on Rte 11. I'll send you a PM.

 

[deezler]

Planning the collection of my Kioti 4010 this week. It has a FEL, Backhoe and 60" rotary cutter. I figure I can use the loader to put the cutter in the bed of the truck

What? What kind of truck are you hauling with? Fitting a dangling HD cutter into and out of a pickup bed sounds like a recipe for disaster. Just put it on the front of your trailer, under the front loader of the tractor.