High flow hydraulics to FEL

[tinygiant]

I own a Kubota 7060 that runs 11-12 gpm. I'd like to have the option to run some skid-steer attachments that require a flow closer to 22-25 gpm. Can anyone point me at a recommended product (like a PTO hydraulic pump, or even something that could be mounted permanently, if it exists) for this model tractor? Anyone with experience on the good/bad of a similar setup?

Thanks!

 

[part-time-Farmer-NC]

Grainger has a pto pump that does 22.1 GPM for close to a grand. If you can drop your request down to 21Gpm you can get one for about 1/4 the cost. Of course you will also need a reservoir, and hoses.

 

[5030]

You can buy self contained hydraulic units that run off a 540 PTO, but they aren't a cheap date.

 

[tinygiant]

Thanks, will start looking ...

 

[Mulder]

What I did is pto pump from surplus center not sure what gpm a 40 gallon fuel tank I mounted on my box blade it's permanent now. Because my tractor had a lever for either hydraulics or 3point not both at same time now I have 3rd function front end loader hydraulics and 3 point at same time with top and tilt. Have about 1500 in the hydraulic setup also upgraded joystick controls for float mine originally did not have

 

[Smokeydog]

Most skidsteer hydraulic motors that size have a supply line, unblocked return and case drain back to tank. Three lines. Tank size and cooler depending on application. Tractor loaders aren’t nearly as stout as skidsteers.

 

[kennyd]

There are a few commercially available "power packs" like this, they have 14 and 21 GPM options:

PTO Hydraulic Power Pack For Tractors IronCraft

Buy a auxiliary hydraulic PTO power pack for tractors. Mounted to the 3-point hitch and runs off the rear PTO. Power loader mounted cutters and snowblowers.

www.goodworkstractors.com

Of course then you will need large and expensive hoses, couplers, and fittings to get the fluid up front where you need it. Possible? Yes. Practical? Only you can decide.

 

[kennyd]

Another Power Pack:

Hydraulic PTO Power Pack - AGRISHIELD

The auxiliary power pack enhances your tractor’s hydraulic capabilities by increasing the available flow to implements. These are great for a wide variety of tools - we have provided solutions to customers looking to power vineyard implements, log splitters, snow blowers, post hole augers, and...

agrishieldllc.com

 

[tinygiant]

Thanks, will look at that one also.

Anyone have experience with the IronCraft Hydraulic Power Pack? 21gpm, fewer bells and whistles. How important is the cooling fan? The assumption is I'd be running skid streer implements such as brush cutters, trenchers and the like.

Thanks,
Ed

 

[oldnslo]

Cooling will most likely be required if running continuously in the summer.

 

[D&D]

I own a Kubota 7060 that runs 11-12 gpm. I'd like to have the option to run some skid-steer attachments that require a flow closer to 22-25 gpm. Can anyone point me at a recommended product (like a PTO hydraulic pump, or even something that could be mounted permanently, if it exists) for this model tractor? Anyone with experience on the good/bad of a similar setup?

Thanks!

Look here,

Power Pack on L6060, how long of hoses and where do you run them?

Hi all, Ordering a 3-pt power pack for my L6060 to run a few skid steer attachments... Getting a 25gal, 21.2gpm unit from Green Hoe. 1. Does anyone have experience with this unit or company? 2. Why type of oil can I use in this? 25gal. is a LOT... their saying no oil cooler is needed because...

www.tractorbynet.com

 

[tinygiant]

Thanks, will look.

 

[ruffdog]

Cooling will most likely be required if running continuously in the summer.

^^Yeah, lots of heat will be created!