LD1
Epic Contributor
Curious too if the other side was the same way? Or if the cutter was just shifted all the way right for some reason?
3-Point Hitch Help removing a King Kutter rotary cutter
- Thread starter DonHite
- Start date
- Views: 13051
Hay Dude
Super Star Member
- Joined
- Aug 28, 2012
- Messages
- 18,713
- Location
- A Hay Field along the PA/DE border
- Tractor
- Challenger MT655E, Massey Ferguson 7495, Challenger MT535B, Krone 4x4 XC baler, (2) Kubota ZD331’s, 2020 Ram 5500 Cummins 4x4, IH 7500 4x4 dump truck, Kaufman 35’ tandem 19 ton trailer, Deere CX-15, Pottinger Hay mowers
Tail wheel = the rear wheel on your rotary cutter
Yes, you are correct, the pin is in the hole for the widest position, but at the end of the arm, where it attaches to the axle of the tractor, there may (or may not) be an optional hole so you can shorten the arm. If you can shorten the arm there, you can utilize the other adjustable stabilizer arm positions and make it easier to get the bush hog off
Yes, you are correct, the pin is in the hole for the widest position, but at the end of the arm, where it attaches to the axle of the tractor, there may (or may not) be an optional hole so you can shorten the arm. If you can shorten the arm there, you can utilize the other adjustable stabilizer arm positions and make it easier to get the bush hog off
LS Tractor Owner
Super Member
- Joined
- May 1, 2017
- Messages
- 7,562
- Location
- Edgewood, NM
- Tractor
- LS XG3025 TLB, Previously MT125 TLB, Craftsman GTS6500
How big is the cutter? It might have a CAT 2 3 point (wider width at the mount) with CAT 1 pins on it. My XG3025 has at least 6 inches of side to side adjustability (4+ inches of travel on the stabilizers) . I would move the pins on the mower to face inboard.
sodamo
Super Star Member
- Joined
- May 20, 2004
- Messages
- 15,817
- Location
- Big Island, HI
- Tractor
- LS XR4140H (Mine) BX2380 (wife’s)
From the pic, you didn’t take the stabilizer bar pin out.
CobyRupert
Super Member
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 6,494
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
So did you get the hay spear on okay?
sodamo
Super Star Member
- Joined
- May 20, 2004
- Messages
- 15,817
- Location
- Big Island, HI
- Tractor
- LS XR4140H (Mine) BX2380 (wife’s)
always pull both of mine when mounting/unmounting.
Last edited:
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 6,494
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
So that means you figured out how to pull the stabilizer pins on BOTH sides to make the lower links as wide as possible?
Sometimes I use a bar or steel fence post for leverage to help align the implement.
It will get easier with practice.
Sometimes I use a bar or steel fence post for leverage to help align the implement.
It will get easier with practice.