Good morning!!!!

   / Good morning!!!! #209,133  
Hot and humid, but a nice breeze...just got back from a hike and swim for Della.

Hope you had a great birthday, Kyle...you deserve the best.

Finally cleaned the zero yesterday, scraped the underside of the deck, and swapped out the 3 blades with the ones I sharpened. I just had to try it out and mowed for an hour. I should have weighed the gunk pile I scraped out...lifting up the tarp it was on was a job...grass has been so damp, it really accumulated.
 
   / Good morning!!!! #209,134  
66F steady rain heavy at times with gusty winds ending around 5:30pm.

Been slow putter day still little sore from yesterday work out.
Tomorrow I'll start looking for part time job that will fit my hours and interest...I'm getting bored :( Mrs. gave me :rolleyes: look.

Plans for the evening next to nothing.

Enjoy your evening all.
 
   / Good morning!!!! #209,135  
Good Afternoon,
The critter was not a ground hog but a skunk 😳
But I think he is out of the barn, at least I hope he is because we will be leaving tomorrow and he won’t survive 2 weeks with no water 😉

Ponytug, yes Riptides Mike is MIA, I need to send him a PM ! 🥲

He might be tied up with work ?

Hope all had a good worship today and enjoyed another day on planet earth 🙏
 
   / Good morning!!!! #209,136  
Finally cleaned the zero yesterday, scraped the underside of the deck, and swapped out the 3 blades with the ones I sharpened. I just had to try it out and mowed for an hour. I should have weighed the gunk pile I scraped out...lifting up the tarp it was on was a job...grass has been so damp, it really accumulated.
Sounds like we both had the same results.
I use Mrs. hand metal flower trowel for scaping etc. does nice clean job (y) need to clean under deck more often tho.
 
   / Good morning!!!! #209,138  
Popgadget, do you program your smaller holes a little oversize or use cutter comp, or slow your feed down?

I use Fusion 360 to generate the G code, I select optimization, which lets me slow the feed rate by whatever factor I choose. It was 50% and only inside curves. It also does the compensation for the kerf that I specify.
It took some tweaking to get it accurate.
 
   / Good morning!!!! #209,139  
But Paul suggested a much better way, cut off the oem connector and solder it on the new speaker. Which we did.

IMG_6969.jpg
 
   / Good morning!!!! #209,140  
Good Evening Thomas,
You must be little anxious getting back to radio interest with new ideas Scotty.
Yes Thomas, I have been kind of over the top with ordering new radio equipment much to the chagrin of my lovely wife Kathleen! 😉 Smd I just ordered a bunch of new equipment for operating portable out in the parks. I think it’s about time to start saving money next month considering I’ve spent well in excess of $$3500 or more ! 😳 But when your having fun ??? 😉 I just feel if I can break my butt hauling oil hose,if I want to have some fun occasionally I should do it considering i probably only have a handful of years left ! JMO ! 🙏
 

Tractor & Equipment Auctions

John Deere Quick Attach Pallet Forks (A50514)
John Deere Quick...
Toro 30495 Groundsmaster 7200 72in Zero Turn Mower (A48082)
Toro 30495...
2018 FREIGHTLINER CASCADIA TANDEM AXLE SLEEPER (A51219)
2018 FREIGHTLINER...
DRILLING CABINET (A50854)
DRILLING CABINET...
2005 JOHN DEERE 5205 TRACTOR (A51222)
2005 JOHN DEERE...
2017-2023 Ford Super Duty 4x4 Pickup Truck Bed (A49461)
2017-2023 Ford...
 
Top