Flail Mower Recommendations

[JethroB]

My original belts lasted only a few hours regardless of proper tension and adjustment turning into an overcooked gooey mess, they were just crappy belts. I hit my local NAPA and swapped out to Kevlar belts that I have yet to re-adjust after numerous hours of use over the last year even after several inspections.

I over greased the belt pulley bearing once early on. Rookie mistake. That and tilling the dirt way too much. Made my own gooey mess. Replaced with 3 regular Gates belts. Couldn’t find or see any mention of being Kevlar belts though.

 

[leonz]

Hello and good afternoon scootr,

I want to welcome you as the newest resident member of the "Flail Mower Nations" from the Golden State.

The scraper bar is ment to keep the roller clean of any wet grass or mud. You can keep it tight by investing
in 2 fine thread bolts and fine thread nylock nuts.

 

[diesel85]

Yes, like leonz says, you need that to keep the roller clean from debris. He's got a good suggestion with the bolts and nuts.

 

[Beeenvenue]

Yes, like leonz says, you need that to keep the roller clean from debris. He's got a good suggestion with the bolts and nuts.

I had to take mine off. No matter how unadjusted it the wet clay would lock up the roller and the flail would skid along on it, so off it came. When I have to cut in wet stuff now sometimes the roller builds up but at least it keeps rolling

 

[BeeJay42]

I have a MF-285 - 82 HP with 71 HP at the PTO reportedly. I have recently purchased the family farm from the trust and need to do LOADS of clearing. 26 tillable acres and about 60 in brush or heavy woods. Unbelievable amounts of blackberry bushes and loads of small trees. Most areas are unreachable due to the large amount of scrub.

I would like a flail mower that is at least 6 feet wide and probably less than 7. As I am currently working on a project two days drive from the farm, I only make it back about 3 times per year for a week or two each time.

I want a machine that can handle up to 2 inch of a various types trees and tall weeds. Ones larger than that I will cut down and chip. Need a dependable machine as I don't have time to mess around with getting parts, etc.

Also need a good chipper / shredder that will handle up to 5 inch limbs. I understand from the review this means a 8 inch rated chipper as no logs are typically straight and easy to feed.
I appreciate reading these posts and am tossing back and forth on the six or seven dependable looking machines.

 

[BeeJay42]

I have looked at the forestry mulchers, but $14,000 per week with a cap on the hours it can run per day would take a lot of money. There are guys who charge less than that for coming out and doing it for me. No reason for me to spend that type of money. It would do a better job and I would like to have a month with one of those, but that is not reasonable.

 

[leonz]

How many distributors of forestry mulchers did you contact for rental prices??

The only other would be to have the job bid out with a logger that does land clearing
as a side job or I would rent a dozer for a week and go over every inch of scrub land
breaking everything off at ground level and hiring a big chipper with a grapple or
tub grinder to come in and break it all up after you have it piled in a few spots.

If you invest in a flail mower for your Massey Ferguson 285 and a wood chipper you will not
be able to manage it and your flail mower will be damaged.

 

[DieselBound]

I have a MF-285 - 82 HP with 71 HP at the PTO reportedly. I have recently purchased the family farm from the trust and need to do LOADS of clearing. 26 tillable acres and about 60 in brush or heavy woods. Unbelievable amounts of blackberry bushes and loads of small trees. Most areas are unreachable due to the large amount of scrub.

I would like a flail mower that is at least 6 feet wide and probably less than 7. As I am currently working on a project two days drive from the farm, I only make it back about 3 times per year for a week or two each time.

I want a machine that can handle up to 2 inch of a various types trees and tall weeds. Ones larger than that I will cut down and chip. Need a dependable machine as I don't have time to mess around with getting parts, etc.

Also need a good chipper / shredder that will handle up to 5 inch limbs. I understand from the review this means a 8 inch rated chipper as no logs are typically straight and easy to feed.
I appreciate reading these posts and am tossing back and forth on the six or seven dependable looking machines.

Brush hog (or rent a skidsteer with one)*. You can get ones that can tackle 4"+ material: and with your tractor's power you should be able to run it all day eating up stuff this size. Kind of two issues in the long-run: 1) Initial clearing; 2) Maintenance. If you buy something you can also sell it when no longer required: think of it as leasing (similar to renting equipment except that you place your own time constraints on use).

* Contrary to what some might say, there are brush hogs that are more than capable (some really wicked ones). Expect to see a [new] price tag of around $5k.

 

[professorialtype]

I would avoid Nova Tractor as a company if customer service is important to you. They were helpful as can be when I was researching which mower to buy. After receiving a mower with several missing pieces and no manual, I've emailed three times, left four or five voice mail messages and tried to connect through their website. Three weeks has now elapsed and I have heard a peep.