XmasTreeGuy
New member
I just bought a 6110 Mahindra,only 11 hrs. so far. Is anyone using a block heater? If so where did you buy it?Temps have been very low here & I'd like to have a block heater.
Thanks
Thanks
Block Heater
- Thread starter XmasTreeGuy
- Start date
- Views: 6511
buickanddeere
Super Member
Phillips & Temro Technologies One of thier heating pads under the battery is an asset . Battery tendors are good too. Real class IV synthetic oil.
JerryK
Elite Member
- Joined
- Feb 21, 2004
- Messages
- 3,240
- Location
- Vanderbilt, Michigan, USeh?
- Tractor
- Mahindra (2011)5035 HST TLB & (2016)2555 HST Cab & (2017)1526 HST(2018)Cub Cadet Pro Z 154L (1991) Caterpillar E70B
My 5035 has a pumpkin shaped cast iron ' device ' in the lower radiator hose to install a standard 3/4" screw in heater... You can get them on Ebay or Amazon... I bought a ' Kat's 11619 600 watt ' to put in mine... but will not be putting it in until this summer. Your tractor may have the same inline heater spot.. Good luck, Jerry...
JerryK
Elite Member
- Joined
- Feb 21, 2004
- Messages
- 3,240
- Location
- Vanderbilt, Michigan, USeh?
- Tractor
- Mahindra (2011)5035 HST TLB & (2016)2555 HST Cab & (2017)1526 HST(2018)Cub Cadet Pro Z 154L (1991) Caterpillar E70B
Looking at the parts site, your 6110 uses a different screw in heater than my 35 series. Says it screw into left side of maybe the block, where the pumpkin shaped thing in mine is called a B/H adapter, probably bottom hose... Your dealer can fix u up with one.... 
OP
XmasTreeGuy
New member
Thanks for the replies. I'll check block. What parts site are you looking at Jerry? New Mahindra owner here.
JerryK
Elite Member
- Joined
- Feb 21, 2004
- Messages
- 3,240
- Location
- Vanderbilt, Michigan, USeh?
- Tractor
- Mahindra (2011)5035 HST TLB & (2016)2555 HST Cab & (2017)1526 HST(2018)Cub Cadet Pro Z 154L (1991) Caterpillar E70B
Can't remember which one I looked at... but if you Google ' Mahindra 6110 block heater ' you will get hits like...
Error
There are some parts dealers on TractorByNet, too... This link says 'ERROR', but works .... Good luck, Jerry
Error
There are some parts dealers on TractorByNet, too... This link says 'ERROR', but works .... Good luck, Jerry
OP
XmasTreeGuy
New member
I took a quick look this afternoon and didn't see the plug in the block for the heater. I'll take a closer look soon. I don't see anyway to use one of the in hose heaters,so it will have to be an in block heater looks like.
wolftree
Platinum Member
- Joined
- Feb 9, 2013
- Messages
- 647
- Location
- Thornville, Ohio
- Tractor
- No longer Searching. Mahindra 3016 Shuttle
I have been looking at Wolverine adhesive pad heaters that is glued with a 3M adhesive to the oil pan externally. Has anyone else looked or used a Wolverine?
johnsonauto
Silver Member, Approved Advertiser
We have installed several block heaters in the 6110, you have to knock out the freeze plug on the side of the block, tap in the adapter and thread in the block heater. If I remeber correctly around $100 shipped to you. Can have it to you in the matter of a few days.
NewGuyInNewEngland
Bronze Member
Hi Jerry,
I have been searching everywhere, including google, to find the info you provided here re: coolant heater for my 2010 5035. The glow plug went away last winter so had to keep the old girl in my 45 degree heated garage, preventing my winter projects from getting done! :banghead:
so Thank You for this valuable information!
I am about to order the heater and wanted to know if you installed it this summer and did it fit without hitting internally? Is it working properly in your 5035? Would appreciate a follow up. You can reach out to my via my email address if it's more convenient: cfcbassman@gmail.com
Thanks again.
atb
Gus
:drink:
