massey ferguson 231

Can someone share a picture of their position control and draft lever decals. Mine are pretty worn. Thank you very much!!

Does anyone know where I can get these replacement decals?

I know the lever on the outside controls the rear lift mechanism? What about the inside one?

I have no idea what all the buttons/knobs do….can someone help?

I have a what I thought was a 230 but Im guessing the hood was changed out. I bought another 230 and it is a little shorter and has different steer setup. google shows a 231 on the net with the small hydraulic steer cylinders and a 230 has rods. Whats the difference in these?

Here is the rebuild kit for the power steering control valve for a Massey Ferguson 231 tractor. It might fit all the year models, I’m not sure, but it fits my 1998 year model. The control valve is known to leak over time and this is a good, high quality solution. There is a good video on YouTube...

Maybe this will help somebody out. I found a replacement oil fill plug for the power steering pump on my 1998 Massey Ferguson 231 tractor. Dorman part #090-006. The bolt is a 5/8-18 threads with a 7/8 head. I got it at my local O’Reilly Autoparts. It fits many different year models of...

Hello, I have a Massey Ferguson 231 that after a day of bush hogging the PTO and rear lift quit working. The tractor drives normal but the PTO wont engage in either setting and the lift wont move up or down. The fluid is full and clean. Any ideas before I start tearing into the gearbox to...

Front hydraulic pump: 17gpm driveshaft not turning. Driveshaft spins but pump shaft does not. Loader suddenly would not operate. 2 spool valve body with joystick controller 1996 MF 231/232 need pump removal tips. I have a video but not sure how to upload it. Pics are mostly after I started...

The power steering on my MF231 has been heavy and sluggish feeling. Today I removed the pump and changed the filter and refilled wiht new fluid. The old fluid wasnt that bad. The filter did look dirty. Unfortunately this did not help the PS at all. Any other things to check?

Hello, I’m changing the fluid in my Massey Ferguson 231 and I’m trying to remove my strainer filter and clean it out but the cover is not wanting to let loose. I see there is a gasket underneath it but I’ve tried to lightly tap it with my hammer but nothing is happening. Wanted to come here and...

I picked up a 2003 231. Changed fluids because it had been sitting a while. Power steering got weak. Found out it pushed all fluid into engine oil. Changed out pump. Changed oil. About 10-15 hrs it's doing it again. Trying to figure out which way to go next. Looks to me that the only two things...

Brush hogging and she shut down after about 30min. Cranks but won't fire up. Fuel bowl looks fine. Oil is a little low but shouldn't be low enough to be a problem. I recently went from a 5' to a 6' cutter and could tell she was working harder but I didn't think it'd be a problem. What should...

Hi, I have a 232 loader on my MF 231 tractor. Considering a hydraulic top link but have a question. Tractor has a loader and it has rear remotes. What controls the rear remotes? I feel like something is missing.

Hi, does anybody knows if the MF 236 loader is compatible (plug n play) with the MF 231 tractor?. I know the loader MF232 is the one used for the MF 231 tractor but the MF 236 loader coming from a MF245 tractor seems very similar. Thank you in advance for your help Butteworks.com

Hello, I hqave a MF231. I recently purchased MF 232 loader and am trying to tap into the internal hydraulics to power the loader. I purchased a hydraulic selector valve but it doesn't have a return port back to the selector valve form the loader control valve. The 3 ports shown only supply 3...

Bought a MF231 a couple days ago to manage property we bought to build and small scale farm on. I have a little experience operating a New Holland 65 about 20 years ago and have been borrowing a Kubota L2900 the last few weeks but I'm completely new to MF and have only figured out the basics so...

Got a 231 with the rear brakes sticking, anybody know how to remove the rear brake drum,,thanks in advance

I was able to put a new seat on my 1998 Massey Ferguson 231 tractor today. It’s the classic “bucket style” seat. It’s all aftermarket Sparex parts but it’s as close to original as you can get. I ordered everything through Lindstrom Equipment in Wisconsin. Total cost was $255. The new Sparex...

I have a June 93 Massey 231, the battery kept going dead in about 30-48 hours, I installed new battery, new 2 ga cables and new crimp on ends from Napa, did a draw test on battery and sure as all get out, draw. Now when running it shows 12.94v - 12.96v constant. So its charging, I am cleaning...

Hello, Does anyone here recommend someone or a shop who can re-seal the injector pump on my 1998 Massey Ferguson 231? I’m aware I’d have to ship it. It is dripping diesel where the rotor head goes into the pump housing. There’s an o-ring there. I’d like the whole pump re-sealed since it has to...

All the replacement switches I have seen at least 6 poles, and my MF 231 has 3 wires to attach. How does one figure out the placement of the wires? Colors are somewhat faded, but they seem to be: Green with Gray stripe, Brown, and Gray or Black. The original switch has 3 poles. Thank you!

Need power steering cylinders. 3401285M93. Where to buy? Tried to reseal but they still leak, open to suggestions. I bought a seal kit, the shafts are good. Thanks, Chris

When I try to start the tractor and turn the key, it just clicks like a battery Is dead. I repeat this four or five times typically and then the starter engages, turns over fine and starts. I have replaced the ignition switch with no change in results. Any idea of what is causing problem? Berclair

I have a strange fuel issue going on. Some days the tractor will gradually start losing rpms from idle around 1100 rpm or less and pick back up or either die. When it does die, it is hard to start. The engine is turning over fast like it is sort of running with the starter keeping it going but...

Does anyone now the taper callout (spec) for the steering shaft where the wheel mounts? I need to fabricate an adapter for mine. Thanks in advance.

Perkins powered 231S. I need to remove the starter for service and rebuild. Does anybody have a exploded view of the starter motor mounting fastener details? I can't see behind the starter to determine what to loosen. Thank you in advance.

Tractor was put in shop because the top attachment point of the 3point hitch (the draft control link?) or whatever it's called was found loose and could be turned left and right and nothing would happen. Before this the lift arms worked normally. Now after the repair, the lift arms have no...

MF 231 tractor Tractor was put into the shop because the top link attachment point of the 3 point hitch (where it connects under the seat) was broken. You could try to screw it in and out, but nothing would happen and it would rattle when moving it around. Before this repair, the lift arms...

Hello, How do I go about getting the strainer cover off? I have removed the three bolts. I have tried using a crowbar, but I don't want to damage the plate getting it off. Thanks!

Anybody know where the engine serial number is located on my 1998 Massey Ferguson 231? It has the Perkins AD3.152 engine. Thanks

Hello, I’m sick and disgusted and I love my tractor! I’ve had my Massey Ferguson 231 for 12 years and it’s been an excellent tractor. The other day I was doing some work with the grader box and I noticed at engine idle it started letting out a lot of blue smoke. It’s never done this. I ALWAYS...

I'll be in the market for a compact tractor later this year and was looking at the Kubota LX2610. My neighbor has a relative that just passed away and his wife has a Massey Ferguson 231 with a box blade and a rotary cutter for $5,000. It is garage kept and looks new. He bought it new to clear...

I have a MF 231 made in 1993. 3 point hitch seemed to work till I put a load on them. Would not lift the tiller or mower. I put a pressure gauge where the stand pipe comes out of the plate on the lift cover. Had only 500 PSI at best. Changed the filter and fluid, no improvement. ACGO web site...

Checked the hydraulic fluid, and it's milky from water intrusion. Shifter boots are bad so I will replace them. How do I drain the fill the fluid and clean/replace the filter or strainers? Still trying to convince the bossman to get a shop manual for it... What fluid does it use? I have two...

Hi, I have a 99' Massey Ferguson 231 that just broke in a big way. I was moving some big pine logs that we had taken down in the front yard and was pushing one to be better able to pick it up when all of a sudden it stopped dead(I didn't see the large boulder it had jammed against. Before I...

I’m sure this will help somebody out so I figured I’d post. Here are the power steering fittings with part numbers that go on a MF 231. Common for them to be easily broken off or start leaking. They are no longer in production by Agco/Massey. These are aftermarket. You have to have a short...

I’m looking at buying a MF 231 and was wondering what things I need to be looking for on it, or anything that would be a deal breaker. This will be my second tractor and will be used primarily for bush hogging with my 5 king kutter bushhog. I’ve found a couple I will be going to look at, both...

Hey All, we have an MF231 that has had issues since last winter. It will blow a lot of blue smoke and drip some oil out the breather tube after it has been running for 15 or 20 minutes. It occurs quicker if it is being run and worked in high vs low range. It was never an issue and the tractor...

mf 231 leaking oil badly out of weep hole in belly of tractor....replaced rear main seal.....still leaking???anyone have anymore suggestions. My guy working on it is stumped...Thanks in advance

Hi All, First off, this is my 1st post, so please excuse my rookie errors. Not even sure if I'm posting in proper "place"? I have a 1997 MF 231 (not MF 231S) that always started strong on first attempt w/o ever giving it gas, but now won't start. Has a strong battery. I inherited this tractor...

Looking at a MF 231. Location of hood release?

Looking at a 1998 MF 231. Location of hood release?

I have a MF 231 S that the lift will pick up fine but when you go to lower the implement it will not unless you have a lot of unnecessary weight or you get off and go push down on implement. This tractor was bought new and always kept inside and has around 1500 hours. With that said it did have...

Having some issues with my 231, the other day it seemed to start running rough after about 30 minutes of use. I did not have much time to look so I killed it and the next day it seemed fine again. Then again after about 30 minute it ran rough (like it was missing) and then it died. I put a...

MF231 tractor, alt went bad. Got a replacement and put it in, but the wiring seems wrong. With the key on but engine is off, the alternator is getting smoking hot. From my research, a red wire should go to the large terminal at the 12 oclock position, and a gray wire should go to the D+...

Hello Anyone and Everyone. I have a MF 231 that is stuck in reverse. I was shifting out of reverse one day and it seemed to fall into the neutral position without moving the gears out of reverse. Someone has said to me its a shifting rail problem. Has anyone encountered this problem with any...

Got a question... Can part of the steel fuel line going to the lift pump be repaced with rubber fuel line? Thanks in advance!

I have a Massey Ferguson 231 tractor whose left steering cylinder needs replacement of seals. However in attempting to remove the steering cylinder I am unable to get the end off. Even when hammering with a handheld sledgehammer that does not seem to loosen. Any help would be appreciated. Mike

The steering box on my 231 seems very loose -- takes about a quarter turn of the wheel to effect a change in the steer arm. This is a bit unnerving when operating on the highway in road gear. What is the hassle factor in tightening this up? Shouldn't be worn out, since the tractor is a 700...

I need to know what this power steering cable connection to the power steering cylinder is called? My cable broke off right at the cylinder. I need to purchase that small "nipple" connection to the cylinder. Circled in yellow below. AGCO part number or other? Thanks, much!!

I looked at a 1995 or 1996 MF231 with about 1200 hours. Seller wants $7500. Barn kept. Only question I have is some fluid leakage on both sides of tractor roughly in the area of the lift control on other side and whatever the other control is on the other. I didn't see an obvious leak, but...

Hi all Where do I find the glo-plug on my 231 MF and is it easy to replace or test? thanks Haycutter

Hi all, Can someone tell me where the fuse box for my 231 MF (1995) tractor is located?:confused2: For some reason it will not charge the battery, I just recently replaced the alternator which was bad. Tractor cranked for three days and today was drained down. I am now thinking a fuse or...

Fixing to change the trans/hydro oil in my 231. It currently has "Supertrac Universal" oil in it but I don't like it because to me, it makes the rear end noisy. I'm thinking about putting Amsoil synthetic in it. I use Amsoil in everything I own. Even the 3 cylinder Perkins diesel that's in the...

hi all i got a problem that has me wanting to beat my head against the wall. i hope some one here may have run into the same thing before is was bush hogging and the tractor [m.f. 231] reved up then shut down when i cranked it back its like it had air in the fuel system and to a bit to start so...

sorry - probably been asked before - Tractor is working fine. The trans/hyd dipstick shows the proper level - between the M and A. BUt - when I open the plug by the shifting levers and look in the reservoir - it is empty? Most reservoirs are a reserve to be drawn upon when needed. Should...

still looking for a good used tractor in my price range. going to look these 2 this week. '84 ford 3910 diesel, p/s, good tires, hour meter 'shows' 1800 hrs. $6500 obo. the other is a '99 mf 231, diesel, p/s, excellent cond. 750 hrs. $6500 and he's firm. i'm tired of looking and will buy one of...

My MF 231 with ~2500 hrs was working fine today as I used a finish mower on a 6 acre field...but gradually it lost power...still runs but needs much more throttle. What does this power loss indicate? Any suggestions? Thanks, Butch4

i have 231 MF with the round 12V sealed beam headlights. they have a rubber seal which slips around the opening in the grill for the light. it also keeps the light supported in the opening and i assume must keep some of the water out as well. i broke both headlights and lost one of the seals...

Have what is supposed to be a MF 231 made in Poland, probably in late 1990s. anyway, I need to replace the steering cylinders and a replacement is available for $506.10 each, but no seal kit is available and even these new ones cannot be rebuilt with a new seal kit if the need arises in the...

I have a 1999 MF231. I got it for a steal and it looks and runs great. However, this is my first tractor and not sure if the tractor is operating as it is supposed to. When I am pulling a 5 foot bushhog, I lower the bushhog all the way and it runs great. However sometimes the bushhog will...

Help, Yesterday my MF 231 was running great, like always, and suddenly it appeared to run out of fuel. I confirmed the tank had diesel fuel. It is clean, no water in the fuel filter, and fuel is flowing. The motor will turn over but won't start. What is the next step? Thanks, Butch

I need some help figuring out what kind of fluid is safe in the power steering pump on a 1998 Massey Ferguson 231. One of the hoses to a front steering cylinder got loose, while brush hogging, and leaked red fluid. I tightened the loose fitting, but now I need to add or drain and fill the...

Will a 1040 MF front end loader fit a MF 231 tractor? a pic of the loader is attached my tractor is 2 wd, but i want a loader, and this used one is priced right... anything i should inspect before purchasing? seller has controller,not pictured. i do not have remote hydraulics... I do not know...

Can someone help me determine the price I should put on my Dads tractor? 1990 Massey Ferguson 231 w/ 232 front end bucket About 200hrs run time. Has been weathered outside so looks kinda rough. Not positive of year. Here's data tag info. MF 231 5681 G 22084. Located outside Houston Texas...

As you can see in the pictures, the support bars are bent. You'll also notice that the brush hog is tracking to the left side of the tractor. Not sure what I'm doing wrong here? Do I need to tighten up the top link or the side chains? Unfortunately I forgot the Woods BH owner manual which had a...

I have recently came into a MF 231. I have never owned a Massey. I have owned several tractors. I have ordered a parts and service manual, but would like to start some projects on the machine and would like to ask a few questions pls. The tractor looks rough but runs fine. 1. There are two...

Would like to know if there is a wider front tire option that will fit my MF 231? The tractor has the stock 6.00-16 tires on it now but they tend to cut in around the wet stuff. Does anyone know if there is an option that will give me more float on this tractor? Thanks

First off, anyone thinking about buying a MF 231 should check out the parts availability for this tractor. The on-line sources rarely show a 231 application. The parts list just jumps right over the 231. And if you aren't knowledgeable, like me, you don't know if a part for a 240 or 230 would...

This should not be so difficult. I've found lots of engine ID sources, but none that match up with what I have. I can't find any reference to a MF 231 engine (Perkins 3-152) with an engine model with a "C/I" designation. The engine has these numbers: 3778643 C/I next to the lift pump under...

I could have the name wrong on the ROPS? I have a MF 231 with a ROPS that looks like this I'm looking for a Canopy that will work. Everything I've seen on the web is mounted to the rounded end, foldable ROPS. I had a link to www.tractor-canopies.com but apparently they are out of business...

Started the tractor this morning for snow clean up, part way in the tractor heated up. Shut her down to check things out to find a broken belt! I have been looking at this for a good hour now and it appears that I would have to almost pull the front of the tractor off to change it. Does anyone...

Can anyone tell me why the Perkins AD3.152 engine has a better HP rating in the MF 240 vs. the MF 231?

Went to look at the MF 231 advertised locally. First thing is,the loader is not the original type loader(232 loader) it is some sort of industrial loader.No numbers or plates to ID it. This isn't a big deal really,just would be nice if it was the right loader. Second is,the control valve is...

I know that the 135 was a bit iffy for having a loader,and the 231 is an updated version of the 135 so I was wondering if the front end was updated/beefed up to handle a loader. I would think in the intervening 50 years MF would have done so but oyu never know....:D

I bought a MF 231 with low hours for a song. The only thing wrong with this tractor was a lack of sufficient braking power. After visiting numerous sites I found that was a common problem with this model with no known fix. I didn't give up. I came up with a fix that cost under ten dollars...

Where does the needle on the temperature gauge supposed to stay at (as long as the tractor is at operating temp. and the radiator is cleaned) when you're bush hogging with the 231 ? My temp gauge is original. Half of the gauge where the needle reads is "green" (normal operating temperature) and...

Here's a video ya'll might wanna see of my Massey Ferguson 231 and Bush Hog model 285 rotary cutter. This was taken at my uncle's house. I was cuttin' his overgrown field. It was rough but I got it done! :laughing: :thumbsup: Just listen to the "lope" of that 3 cylinder Perkins diesel!! There's...

How hard is it to change the powersteering filter on my '98 Massey Ferguson 231 ? It has 940+ hours on it and I know it's never been changed. What is the process? Thanks!

i have a massey ferguson 231 that is pumping diesel into the crankcase, i already changed the lift pump so it has to be the injector pump. i was told that removing the pump is tricky due to timing issues. can anyone tell me how this is done? can't afford to pay a mechanic to remove it and...

Hello all Local JD dealer has a newer mf231 sn 5681H07047 listed with 170 hrs and a koyker 160 loader. Whats the scoop on these tractors ? are the the newer model of the MF35/MF135 line? Seems to be a exact copy of my 1963 MF35. Is the reliability of the new 231's silmiar to the old...

I'm having trouble finding much in the way of service manuals. I think I need to tear apart the 3 PH on my MF231 diesel. Lots of 231s manuals but not much in the way of a 231. I'd like to find a downloadable one. I've looked at most of the googled web sites and did find one for about $100 and so...

Two issues with my friend's equipment and let me say I'm very inexperienced so feel free to talk very slowly to me: 7 foot Howse brush hog....the gear box shaft splines to the jump stumper, and the stump jumper splines are toast...both are basically worn slick. No idea how that is even...

Is their two fuse boxes on a MF231? I see one on the left side of the steering wheel that seems to be just for the lights. Where is the other one? I'm having a problem with starting it. I have power all the way coming from the ignition switch to the neutral safety switch. The wire going from the...

I borrowed my father-in-law's MF231 to mow the lawn, and a low-hanging tree branch broke one of the lens on one of the amber marker lights ... the round ones mounted on the rear fenders, up by the roll bar. I would like to fix it, but without a manual I have no part numbers or any other...

I really need a grille and headlights for a mf 231. no luck at dealership. would be nice to get complete with wiring too. thanks christopher keene

Hello, The charge light (looks like a lightening bolt) indicator on the dash just started blinking. When you first start the tractor, it comes on and stays on UNTIL you rev the throttle alittle then it goes off. Now, after alittle while the light will come back on and start blinking. It's...

Hi all, I just got a MF 231 tractor with a MF 232 loader. I did not get the manuals with the tractor, but plan to get them ordered ASAP. I wondered if anyone could help with something. Where do you check and fill the transmission/hydraulic oil. The 3 pt hitch seems a little slow/shakey near...

hi everyone, i have recenly moved and have been doing some improvements to my farm, included with those improvements is building a road, so i had a couple loads of filler dirt brought in and i attempted to start moving it and spreading it, but all i have is a very light grader blade, and...

A 1989 1 owner 231 shed kept, pictures look good owner said he serviced yearly 1314 hours whats it worth?

Anyone know where I can get a complete headlight assembly for a 1994 mf231. Thanks

Hi all. Great forum with lots of good info and folks. Normally I can find out what I'm looking for with the search feature but not this time, so I registered to ask my question. I have a 1996 231 bought new without aux hydraulics for the purpose of light mowing & bushhogging around my...

Long story short.... I think I have a broken ring in the engine. Can any one recommend a good place to look for engine kits??? Thanks any tips and wisdom is welcome.

Here is the fuel and engine oil filter references for the 1998 Massey Ferguson 231. The Napa Gold filters are a for sure fit, because thats what I use most. I crossed the numbers over on the Baldwin and Wix filters website, but havent actually used the Baldwin and Wix filters on this model...

The coupling or shaft driving the auxillary pump for the loader broke. can anyone tell me the best easiest way to remove from front of engine? Does it bolt onto the pulley or what? the pump end is a spline. Any help is greatly appreciated.

I have a MF 231 that has between 1400 and 1500 hours on it. The power steering needs to be replaced. My question...is replacing the power steering worth it on the tractor with this many hours? is it a pain to replace the power steering?

New to the forum, just want to post a pic of my tractor.

Hey guys! This is my first post,and I'm preparing to buy my first tractor, so this is all new to me. I'm looking at a 1998 MF231, 2WD, Bush Hog quick disconnect loader, and canopy. It has 398 hours on it, and looks hardly used. The dealer is asking $10K. Is this a good deal? Also, would this...

I was wanting to know if anyone on this board owns a 231 and the newer 431 Massey Ferguson tractors. At the present time, I own a larger tractor with cab, and 4X4. On my farm, I am needing a smaller tractor with no cab in the high 30, or low 40 PTO horsepower range to use in places that I can't...

I posted this for a friend on the MF board, but figured I'd put it here too: The power steering pump on his 231 bit the dust. He's wondering about rebuilding it or replacing it, perhaps with an after market part, since these pumps seem to go out after short hours. Any suggestions? Chuck

Posted for a friend: The power steering pump on my 231 bit the dust. Where is the best place to get a replacement, possibly an after market replacement? Is it possible/reasonable to rebuild this pump? Chuck