kubota g1900

Currently have a g1900 non all wheel steer and extended the front battery tray to fit a optima red top 34-78 battery,only using it to pull stuff around, I built a pull behind scraper/box blade that has a electric over hydraulic motor on it and it will drain the battery fairly quick, I run it...

Well, I was talking nice about my G1900s just the other day, and today cutting grass, notices a stream of oil, drove immediately back to the shed, and her oil was empty. Added some more just to see where the major leak was, and it appears to be the main bearing seal. Good news is that the...

My g1900 starts fine sometimes, but other times I need to use a portable lithium ion jump battery. When I use the jump battery, when she is being stubborn, regular mode will not start the motor, but if I put the jump battery to extra boost she starts right up. It does appear to be a...

Between me hitting trees, pins popping out and dropping anti-scalp wheels under the mower deck, a failed alternator, leaky bucket cylinders, mouse damage this winter, I have been getting on my equipment with my fingers crossed each time. Hope I did not just jinx myself.....

Had the Alternator go out on my G1900S...took out the fan belt also. It was original, so 30+ years old and over 2000 hours. Got one on Amazon, next day delivery, and picked up a replacement belt at my local dealer (Dealer was twice the price for a non-Kubota Alternator, 3 times the price for a...

I have a complete snowblower assembly for my Kubota G1900 less the male G2549 quick hitch assembly. Looking to purchase this part. part 70060-03066 Thanks Peter W. Goshen, CT

I recently got a G1900S with only 190 hours on it. It sat in a garage for almost 20 years..... It has a weird intermittent issue in that it won't crank. All the lights come on as well as the glow plug timer and other lights work. Then after a while of leaving it sit is will start. When it is...

Well, the title says it. No power to the lift pump. I replaced the multifunction box and it fixed a few issues as I expected it to. But still not getting power to the lift pump. I found the pin in the multifunction box connector and if I power it there it starts clicking like it’s supposed to...

Make some progress on my new G1900. Found the hot wire from the battery to the regulator had got hot, arc'd and melted the connector to the regulator. The male side of the connection was broke off and sparking and getting very hot as even the insulation on each side was burnt. I hard wired...

Just replaced our little T1600 diesel lawn tractor(its for sale btw) with a G1900 I plan to refurbish. I am hunting the OEM 3 point hitch kit, new or used, for it along with one of the snow blades. If I cant find the hitch, I know they are very hard to find, I will fab up a sleeve hitch set...

Hi everyone. So I just swapped my 1998 Gas EZGO golf cart for this Kubota G1900 with 605 Hrs. It has the 54" deck. I have a few questions about it. 1. Is there any source for free download of a owner's manual ? 2. Yesterday the temp gauge worked and the Fuel did not, Today it is opposite. I...

I have read several threads on this general topic (no start), but have yet to find my solution. I have a G1900 that will not start or shut off with the key. A year or two ago it started with an intermittent no start issue. If I jump the start relay it will crank and start every time. This...

I'm considering selling my diesel Kubota g1900s with a 60 inch mower deck. It has only 880 hrs on it. The only problem is that one of the drive shaft's u joints snapped. It's the one that connects to the engine. The other end with the little white fan is fine. The tractor is about 20 years old...

Hello all just wondering if anyone around the PA area has a 54" deck for a G1900 in good shape. RC54-G20 shaft driven In the off chance that anyone wants to trade the Mower has a 48" deck that is in good shape, professionally maintained, greased, cleaned, gear box oil changed, and blades kept...

I have been using this site for years .. thanks in advance for the indirect advice already! I have a G1900 that has been great for many years. All of a sudden one day it would no longer start. I've been all over the web reading posts of what could be the issue. The first thing I did was test...

Im looking for the PNs for the pieces tha make up the fornt mount quick attach for the G1900. Ive seen them in pics but cant find them on the IPB form Kubota. Restoring a 1900 and would love to get my hands on these parts. If you have a trashed 1800/1900 with the parts on it, let me know Im...

I just bought this excellently preserved g1900s for $3000. Only 540 hours. Extra blades (x2) and parts, WSM, turbo bagger. It mows great. The turbo bagger is for sale as I won't use it. What I wish it had: tach, power steering, grab bars. I've already added a grab bar and will survive without...

Having charging issues with my g1900. Getting 30v AC from the alt and 12v from the key switch to the regulator. Just no output from the regulator. I bought a new regulator but has the same issue.... Unless the new one is DOA.... Kinda stumped. What else could it be?

I have a G1900 with a 48 inch rear discharge deck. Cutting blades are worn and would like to install some mulching blades. Anyone know who can supply mulch blades for the 48 inch deck, have seen gator etc for other decks but not the 48.

I have purchased a TG2742 snowblower, but the subframe is for the rear-engine GF1800/1900, whereas I have the front engine G1800. I am trying to find the frame assembly for the G1800, which I understand is the same as for the G1900. Also, I have no need for the GF mount that is currently on...

I made the mistake of taking the starter solenoid out without taking a pic. Solenoids have no markings on them. Need to reconnect. Could someone either take a pic or post the tos/froms for the solenoid? I have the manual but its woefully vague about the connections. Thanks

Greetings all, Thinking of picking up a G1900 with 1200 hours from an old retired guy. He has some nice old cars and a collection of motorized things, so I feel the tractor was reasonably taken care of. And it was garage kept. Overall the tractor looks to be in good condition with some...

Looking for a few things for my G1900. I need: gauge cluster assembly headlight lens hub caps (4 wheel steer, if it makes any difference)...need all 4. maybe a nice tight steering sector (4 wheel steer). I could also probably use a good 54" deck, but it'd have to be local (I'm in the middle of...

Today after mowing my grass for about an hour I decided to remove the 54" deck from my G1900 and service and clean it. I took the fill plug out of the gear box before removing the drain plug to change the gear oil. There was a good amount of pressure in the gear box.:eek: It almost blew the fill...

Hi All, My throttle arm likes to (quickly) drop the engine down to lower rpm's and not stay put at the full open position. When set to full throttle, it will drop down as soon as its let go of. I've been driving around with a makeshift solution of a board wedged from my seat to the rubber...

Hello, Hoping someone can help as my model cant be towed to get it on a trailer. Unit cranks but wont start. Replaced battery, replaced rectifier (what the dealership told me to do but didnt solve problem), i get ~ 7 volts at glow plugs when cranking but nothing in on position. Glow plug dash...

Over the weekend I was doing some end of season cleanup when I stopped the mower to pickup some kids toys that were in my path. While I'm off the mower I hear an awful clanging sound and immediately shut down. I turn back on and immediately hear the same clanging. Metal on metal coming from...

I've noticed today that my G1900 (60" deck) seems to be bogging down in grass that is the same height and using the same power settings as usual. In fact, the grass is drier than normal due to little rainfall in the last month. I sharpened the blades two mows ago, I keep the spindle bearings...

Hello, Just moved and bought a slitly used Kubota G1900 with a 60" mowing deck. In preration for winter now I'm looking for either a snow blower or blade that fits this model of tractor. The correct parts should be TG2742 for the snow blower and G2001 for the blade. If you know of anyone...

--G1900 with 60" deck-- I was mowing my property as usual today, and looked down about halfway through, noticed that neither of the anti scalp rollers on the leading edge of the deck were spinning. Instead, the axle of each roller had wallowed out the plastic roller so that the hole through...

Has anyone installed new oil pan on Kubota G1900 S? I picked one up at a decent price I think but it has a small (very) leak at oil pan. It may be gasket or in the pan itself. Tractor just need s a little tlc to be a mowing machine again. In looking at the drive yoke for the mower deck, it...

Hi,my kubota G1900 creeps when pedal is in neutral,please help,thanks

I need a machine to mow 1.25-1.5 acres of grass, mostly flat, with some trees/garage/house to negotiate around. Which would you choose if you had these two options?: 1. Kubota L175 for about $2000. Has a Woods 60" belly mower. About 1200 hours. Has been left out in the rain for a long...

I just picked up the plow and sub-frame (and free tire chains, sweet). From the looks of it, I have all parts. I'm wondering how it is designed to attached to the hydraulic lifts that the mower deck uses? I'm in the ballpark as far as hole locations, but the lifts on the tractor have a small...

Hi All, I'm looking for the sub frame for the TG2742 snow blower. The part # for the sub frame is G2744. I picked up the snow blower off of craigslist, but now have no way to mount it to my G1900. My local Kubota store told me I can purchase it part by part and sent me a list of 50+...

My deck belt broke. No manual, so I'm just disassembling what seems logical. So far I have everything disassembled except for the middle blade/pulley/gearbox combination. I need to purchase a 1 3/16 socket to get enough leverage to remove the bolt holding the center blade on (monkey wrench...

G1900s 3 pt hitch - YouTube

Hi, I have a G1900S 4WS. It is new to me and was in need of maintenance. The deck was rusted out, so I have a new galvanized one made. Motor had been rebuild not long ago. Runs well, albeit somewhat hot, but then it is Summer in Oz! My problem is that the speed control was slipping back to...

Hey guys, does anyone know the thread size of the flexible hydraulic line that connects to the cylinder that lifts the mower deck? Also, has anyone ever run a second hydraulic cylinder off of the HST on this model or G1800? Can it handle a second cylinder if used separately? Thanks.

Hi, I have read the old forum pages about hooking up a John Deere relay switch to the kubota that doesn't like to start, but can someone pls post pics or draw me a diagram of how to set it up? I am new and not too much exp. in fixing tractors... am waiting for my brother to bring the part from...

I would like to purchase a hydraulic cylinder and fabricate a 3 pt type hitch or sleeve hitch for the rear of my G1900. The 3 pt hitch option schematic shows a hydraulic line going to the inboard side of the hydraulic control valve and attaches to a cylinder on the frame. My question is.....If I...

Hi there, I recently purchased a second-hand Kubota G1900 with what I believe to be the GCD-600 grass collector - I am new to these tractors having only had Cub Cadets previously so need some help working out why the grass collector is not opening and closing properly! At present, when I push...

I just picked up a TG2742 snow blower. $400 off of craigslist! Drove 200 miles to get it, but I couldn't pass up the opportunity at that price. It came with no manual. From the looks of it, it seems like I will need to purchase some kind of mounting kit and possibly a PTO kit for the thing...

Hi, I just bought a used Kubota G1900S with 1178 hours on it, no owners manual and I need maintenance info, plus how do you get the deck off??? So annoying, I can not find any info online about this tractor, don't even know how old it is, does anyone know how to tell and where can I get an...

My Kubota G1900 wont start. when I turn the ignition, the glow plug light does not come on and the engine will not turn over. This has happened before and usually I leave it alone for a while and when I come back to it it starts, but it has been a week and it still wont start. any suggestions?

Howdy all, New owner of a G1900s with 1700 hours on it. 48" deck. I've only used it for a month (so roughly 4 times total) and it seemingly runs fine. Also new to these forums and I have to say I'm very impressed with the knowledge of this community. You've already helped me replace my pto...

Anyone know what the heck the little PTO shaft is coming out from the rear of the HST.....its really recessed in there. Was there attachments for the rear of the mower? Curious to know what you could run off of that.

Hi does anyone have the part number for the belts that drive from the engine to cutter deck. There are 2 but the same number. Will be pleased for any help. Pauline:confused:

Hi can anyone tell me the part number for the belts which drive from the engine to cutter deck on my Kubota G1900 mower please. :confused2:

I have a Kubota G1900 that is blowing fuses as soon as you turn the key one notch (to the first notch). There was a starting issue and I removed the battery and accidentally hooked it up backwards when I reinstalled. This is when the issue started I believe although there were several spare...

I have purchased the springs to take some weight off of the deck from Kubota. They no longer have all the pieces for a complete kit. Does anyone have the manuel that Kubota printed for the sping kit? If so could you Email or fax it to me? Could someone with the sping kit take pictures of the...

I have a RC48 G20S deck. The four acres I mow is very rough due to night crawlers. This tends to beat the deck to death. Has anyone modified the deck from ground contact to a suspended deck? If so how has it worked out?

I have about 900 hours on my tractor. I mow about four acres and it is very rough due to night crawlers. The hydrostatic pedal no longer returns to neutral from both the forward and reverse positions. I have: replaced the ball bearing that centers the valve shaft -- replaced the centering...

I picked up a B2750 front snow blade because I couldn't find one meant for my little G series mower. It was meant for a B5100 or B6000. The G2001 blade that was designed for my tractor used some goofy linkage that ran off the deck, but were discontinued years ago, so for 150 bucks off of...

Hey Everyone Now that cold weather has hit here in NC my glow plugs don't seem to be working. It will not fire up when it turns over and when I out it to the glow plug location on the key switch the glow plug light does not light up on the dash. I did get it to blink one time. Just wondering...

anyone know where i could buy a front blade for my G1900?

The idle on my G1900S is not even. It wants to slow down and then come back to normal when it is sitting still. It's kind of like it is missing a beat at times. Any ideas of what to look for? Thanks

My G1900 won't even turn over. I pulled the starter and applied external power and the solenoid and starter do what they are supposed to. Gear spins and is thrown forward to engage the flywheel. But when it is on the tractor it will only turn a bit and then stop...... I turned the crank several...

Hey Everyone- I have a Kubota G1900 lawn tractor with about 800 hours on it. I've never had any major problems with it, but when I went to cut the grass yesterday there was a very loud banging at when I reved the engine to higher rpms...so much so that I was hesitant to drive it. After a bit of...

I want to tow my G1900 up a steep slope out of a valley. I've read somewhere this can damage the HST. Anyway I can do this? Thanks

The guide wheels and shafts on the RC48-G20 on my G1800 are completely shot, do to previous owner(s) lack of greasing them. One of the rubber wheels is chewed up too, since the pin holding it on came out while I was backing up and it ended up under the deck while the blades where spinning...

Yesterday (and the day before actually) I replaced the radiator on my G1900. It has started to leak, an although it still worked, the radiator fluid would get the screen wet and then all the grass would stick to it and the radiator itself, causing constant air flow issues. Parts cost was about...

Is there anything wrong with using synthetic oil such as Mobil1 10W-30 in my G1900 diesel? It has 1400 hrs. on it.

What is the best/economical source to get shop/repair and parts manuals for a G1900 Kubota garden/lawn tractor?

I have a 93 or 94 (need to verify) Kubota G1900 diesel tractor that was given to me by a family member. I am considering selling it. What do you think it is worth? Where is the best place to list it? Kubota G1900 4 wheel steering. Diesel 18hp. 60" deck. 420 hours. Runs and drives excellent...

I have a 93 or 94 (need to verify) Kubota G1900 diesel tractor that was given to me by a family member. I am considering selling it. What do you think it is worth? Where is the best place to list it? Kubota G1900 4 wheel steering. Diesel 18hp. 60" deck. 420 hours. Runs and drives excellent...

My Kubota diesel lawn tractor sometimes won't shut off. Does anyone know if repacing the engine stop solenoid would solve the problem? Can it be done easily by a novice? Thanks for any help you can give.

I bought my g1900 a few weeks ago and love it!! I am have a problem trouble shooting the glow plugs. I have no power to the glow plugs and the light wont come on. I checked the glow plug wire (blk/red) the runs from the glow plugs to the harness under the dash and that wire is good. If i turn...

I bought my 1999 g1900 a few weeks ago and love it!! I am have a problem trouble shooting the glow plugs. I have no power to the glow plugs and the light wont come on. I checked the glow plug wire (blk/red) the runs from the glow plugs to the harness under the dash and that wire is good. If i...

just found a G1900 with a 48" deck and 4 wheel steering, not sure on the year but it has 600 hours on it what would a fair price for something like that be?

New G1900 owner here. I want to change all the fluids but the manual hasn't gotten here yet. Is it as simple as just draining everything out and changing fluids and filters? Are there any special steps that need to be taken? Also, if someone wants to take a stab at explaining how to replace...

my neighbor has a g1900 that died in his yard. he wants to work on it in his garage thats about 200feet away. he asked me to borrow my quad to drag the thing to his garage, but i told him that might not be a good idea since he cant find a hydro disconnect. is there ANY way to move this thing...

By G2000, I'm not referring to the G2000 Garden Tractor, but rather the G2000 Front Blade, which according to the table on Kubota's web site: Kubota Tractor Corporation - Prior Tractor Models Is the 48" blade for the G3200/G4200/G5200/G6200 tractors. The G2001 is the "48 inch light duty"...

I have a g1900 that is losing coolant. It does not get hot. The level goes down 1/2 to 1 inch on in the overflow bottle per hour of use. I don't let it run out so it never overheats. I had the dealer check it. They said they pressure tested it and found that it was losing pressure just...

Anyone ever romove the steering wheel on a G1900? If so, can you share any tips? I believe my key switch is bad and the steering wheel needs to come off to get access to the back of the switch. Thanks, Dennis

I ended up with a g1900 that was never sold until this year. As of now it only has about 10 hours on it. I'm not sure who set it up but I'm finding a lot of stuff messed up on it. The deck was mounted incorrectly, wrong/missing deck wheels, PTO brake not attached, etc. Minor stuff so far. Anyway...

I've got a g1900 with a 60" deck. It's huge, and frankly with that much weight I didn't think it would slip so easily. My 44" cub cadet (2518) climbs hills much steeper without losing traction. For those that don't know neither of these has limited slip or traction control. The Kubota has...

I have a G1900S that will not start intermittently. Today after mowing for about 2 hours I stopped the tractor. I blew it off with the leaf blower to get the grass and dust off. When I went to put it back in the shed it would not start. This same thing happened a couple of weeks ago. The Stop...

My G1800 has a dead kill solenoid, so the previous owner rigged it so that moving the throttle lever the whole way slow shuts the engine off. There is a zip-tie connecting the kill lever to the governor control. Would someone with a G1800 or G1900 please take a nice detailed picture of what...

My G1800 has a dead kill solenoid, so the previous owner rigged it so that moving the throttle lever the whole way slow shuts the engine off. There is a zip-tie connecting the kill lever to the governor control. Would someone with a G1800 or G1900 please take a nice detailed picture of what...

Since the pump and the dash lights for the fuel guage and glow plug all went out at the same time, I'm thinking that this is an electrical issue rather than a dead fuel pump. Without a wiring schematic, I don't know where the connections are that I need to look at and test for power and don't...

2 weeks ago I was running some fertilizer on the pasture with the G1900 in between removing the plow blade and mounting the 60 inch mowing deck. Some stupid little stick found the fan, and 4 blades were gone. The good news (I guess) is that the 2 blades left are on opposite sides, so the fan...

Does anyone know at what RPM does the front PTO of the G1800/G1900 turn? I want to connect a two-stage hydraulic pump to mine to run a log splitter. The pump is designed for 3600 RPM, so I'll probably need a increase the speed with pulleys. It is a 28GPM/6GPM pump, and requires a 13 HP...

I was talking to my dealer this morning scheduling the 50 hour service on my BX. We were shooting the breeze on lawn tractors and I found out that he has 2 NEW G1900's, 1 in the crate and 1 assembled that he needed to move. With the choice of a 54" or 60" deck. He's asking $4800.00 for each...

Still looking for a tractor but have come across a JD 455 with 700 hours and a G1900 with 600 hours. Anyone know how the two compare? Which is the tougher of the two? Which is more difficult to get parts for? I did read the other thread but there was too much crap in there about the BX. I...

Hello. I just bought a "new to me" G1900 and now am looking for a bagger (GC54G) and snowblower (TG2742). Any leads are appreciated! Today I came across a bagger with the guy having no idea of what it fits (eBay). From what I can see, the pcs "look like" the needed ones for my Kub, but is...

So today I was mowing with my son on the lawn tractor (he is almost too old for that at 6) and he was fiddling with the key and he turned it off the on and the thing died on the spot. Nothing when I turned the key. It turned out the 10 Amp fuse blew, fuse for the ACC. I borrowed one from my...

Hello. I'm currently considering a G1900 4WS with pretty low hrs. Would be needing a snowblower and bagger for it. - Are these auxillary items commonly available used? I've not seen them in my searches yet. - Is the snowblower a shaft drive or belt? (TG2742) - Are they good units, in...

It is possible to leave the key switch on my G1800 in the "ON" position when removing the key, which is what happened mistakenly when I took a break from mowing to eat dinner this evening ( the shutoff solenoid has never worked on this unit since I've owned it -- so it has a manual shutoff)...

The electric fuel pump on my G1800S died in the middle of my yard today. How does Kubota expect you to move these things when they're dead? I ended up using the B7100's three point hitch, buy connecting my trailer-towing adapter via a ball-mount with the ball removed with a large pin to...

Hi. It is my first post, I figured I'd post here under the buying section instead of the Lawn and Garden Tractors - that forum doesn't get much traffic for such short notice. G1900, 42" two stage blower, 60" mower thats only 2yrs old, weights and chains. 1600hrs. Has recent dealership stickers...

Looking at the following page: Kubota Tractor Corporation - Prior Tractor Models I see that there is a "PTO kit (front)", G2592, and a "PTO Kit (rear)", G2591. Is the front PTO kit required for a snowblower? I'd to add a snowblower to my G1800, but it may be cost prohibitive if I have to...

I am contemplating the purchase of a G1800S. Are the snowblowers for these readily available? What model snowblowers will it support. Also, what about the 3-point hitch? The one that I'm looking at does not have the 3-point hitch, but I may want to add it. Thanks, Jay B7100 w/ FEL...

I'm considering purchasing a G1800 or G1900 with four wheel steering. Are there any problems that I should know about with these models, particularly the four wheel steering? Thanks, Jay '80 B7100 w/ FEL.

I just bought a 97 G1900S that has a rear PTO that drives a roto tiller attachment. I have no literature, other than a parts breakdown,on the rear PTO. My question is what lubricant does this rear PTO take? Also do you fill it to the bottom of the fill hole? I cannot find any plug to remove to...

I've noticed a number of G1900 owners complaining that there mower was slow to get moving - took a while to get the hydrostat warmed up and moving. Reverse was slower to respond than forward. I had this same problem. One observation I made - when the hydrostat was acting up, the fluid on the...

Hello, I have an old G1900 (1200 hours) that needs a new drive shaft (old one was flopping around and making quite a racket. I bought all the parts needed for a new one (my tip: individual parts are cheaper than buyin the whole kit now, $214 vs $280). I have partially assembled the new drive...

I am trying to make a decision between one or the other? I will be using it about 90% for mowing 5 acres. I am not to familiar with the kubota's. the prices i have been finding are less on the kubota for a comparable model versus the JD. Any suggestions would be greatly appreciated! thank you

Hello, New to the group and first time posting. After lots of research, I just bought myself a used G1900 (with only 50 hours on it). It's a 4WS with a 60" deck. I cut my 1.5 acres with it first time last night and what a treat! The problem that I'm having is with initial start. With the...

I am probably going to sell my Kubota G1900 Diesel. Have any idea what I should ask? 18hp liquid cooled Diesel, 54" cut, Hydro drive and deck, shaft drive deck, not pwr. steering but steers very easy. Is in very good condition, only 460hrs. Tires like new. Cuts and runs like a new one. It is a...

Just drove my first hour on Used 400 hour G1900 w/ 54 inch deck,runnin like a champ, then was mowing a rough ground area with hydaulic deck in raised position, when the u-joint popped off the deck shaft. Couple questions: 1. Is that some sort of shear pin that is intended to give way (I did not...

I want to know the price of a used Kubota G1900s with a 60 in deck and 1000 hours. Also what would a used John Deere 445 be worth all wheel steer 54in deck and 450 hours, and what would a used JD F935 be worth 60 or 72 in deck and it has about 1500 hours and it is early 90's

I'm thinking about buying a used G1900 in good overall condition, 54" deck, 800 hours. Here are the few questions I have: Any general opinions on this unit (good/bad)? Is the deck on this machine shaft driven? How much should I pay for this? Should I just buy a new cub cadet 2500 series...

Can you guy's/gal's give me some idea how much to ask for this unit? Mid 90's G1900 4wheel steer, 3 cyl dsl, 60" deck...708 hours...I have replaced the seat with a more comfortable model from Tractor supply...everything works great.... Thanks, Tom

I'm looking at G1900 ~500 hours. Is $2500 a fair price and does anyone have experience to comment on this model?

This eBay listing seems like a very good price. How good is this tractor? I was going to get a JD2210 new w/ FEL & 62MMM for about $13,500 - should I save the money and get this? How high should I bid? My new home is on 7 sloped acres (1.5 lawn / 2.5 pasture / 2 woods / 1 swampy area)

Sometimes I operate my G1900 with the mower in the raised position. This makes it easier to cut very long grass. The manual advises against this but I can't see why. Anybody care to comment?

I am thinking about buying a Kubota G1900 lawn mower, it is in good condition, always well maintained and has 1,100 hours on the clock. I am having trouble finding out the market value of the tractor, can anyone give me some information? thanks.

Have a G1900S/all wheel steer/18 H.P. diesel/60" deck,for sale.Tractor has 142 hours,has been garage kept,with the best of service and care.Show room condition.Have purchased a new BX2200,reason for selling. <P ID="edit"><FONT SIZE=-1>Edited by MReeter on 1/6/01 06:03 PM.</FONT></P>

Does anybody have an idea what a like new G1900S is worth? This lawn/garden tractor has 140 hours,60" deck,all wheel steer,It is in "like new" condition.I can't locate a site that has a "blue book" on lawn and garden tractors.

We are thinking about a rear bagger for our G1900S,the local dealer has priced a unit,installed,for $1450.00.I know this is a very good bagger,does this seem in line? Also,has anyone installed one of these units by themselves?

G1800,G1900s We are considering adding these two models to our offerrings at www.CarverEquipment.com. This would include parts, service, trades-lease-pricing info. Please drop me a note if you now own one of these models and would have advice advice to help us better serve you. Thanks, Steve...

My G1900 Hydrostat drive seems to take forever to warm up and operate properly. Reverse doesn't work at all until warm. Forward screams at me until it is warm. However, hydraulic lift for mower deck works slowly, but it works. When cold it will coast down hills, drive will not engage properly...