kubota bx2200

does anybody know if the bx7326 rear aux. kit to fit a bx2350 will it my little bx2200

well with 635 hrs. the inside pins broke, then got in the main gear and did some other gears then put a hole in the bottom of the housing. I stripped the tractor down to get to the transaxle and took it to the dealer. appr.$1900.00 plus change to fix. the shop foreman said about $3500.00 if...

I am having a hard time deciding on a Snowblower for my new Bx2200. Rear mount PTO blower for BX2200 should be a maximum lenght of what? I have a choice between two used Canadian snowblowers. The first one is 1200$ for a 60 inch dual-stage blower with allot of rust. The next is a fairly new...

has anyone ever had a problem with their transmission whining when mowing up hills or going up a hill in high gear???

Hi, I'm new here and I've owned my bx since it was new. I think since 1999. I was was mowing the other day and all of a sudden it stopped moving. Upon further inspection I notice a trail of hydraulic fluid behind me. I looked under the tractor and it was leaking from the hydro filter. So I...

Hi all! I am new to this forum, but I've been using it for several years to make repairs to my BX. Extraordinary board here and I'd be broke if not for all the good information in here. I thought I'd introduce myself and throw a couple thoughts out there about my experiences with my BX. I...

A couple of very loud bangs came from under the hood when I cranked up a couple of days ago, and upon investigation, I found an unhappy 3' snake considerably the worst for wear draped across the fan belt. Then yesterday the fan belt gave up the ghost.(750 hrs). Don't know if I was snake bit or...

..Just got the BX2200.. No manual.. Took off the loader.. Snap.!! Now I have 3 hydraulic lines hangin in the breeze.. Two are rigid lines, 1 male 1 female.. One is flexible and female.. The female rigid has a cap.. The male rigid and the female flex don't.. What do I do with these lines when I...

.. Hey guys.. Well, I almost made it 24 hours after purchase of my first tractor before I started thinking of new toys for the big toy.. I've seen these grapple attachments and I want one.. Seems like the bucket sides'd get in the way of the ones that attach to the existing bucket.. What are the...

BX2000 (2001 w 600hr) Turn key, starter tries to turn engine. the engine spins about 1/4 - 1/3 revolution and then a loud CLACKING sound. Not quite the clickling sound from a dead battery. If I keep the key to start, the starter will spin the engine another 1/3 or so and then the clacking sound...

Another in my series of hydraulic education classes. I replaced my power steering hoses recently and now am having problems with my steering. I think that I may have introduced some crud into the lines when I fed them though to the steering cylinder. Would contamination effect the cylinder in a...

:( Hello all, I bought a used 2002 BX2200 with 198hrs, brand new!!!! awesome shape!!! I have not been sleeping for one week straight from all the excitement, torn about everything possible in the driveway with my new modern rake and fel.... a hout-a-nanny fun let me tell you. Can't wait for...

I know that there was a factory defect on the early 2200's with the front axle seals. I had mine fixed once under warranty, once again last year, and now it looks as though it is leaking again. Is this normal? And is the seal replacement a bear? I'll be luck to scrape up the $$ for the seals...

Has anyone else had these lines wear a hole in themselves from the clamp? I had this happen on the quick-disconnect side and just made sure that the clamp was tight after I replaced the line, but I didn't think to engineer some sort of protection for the lines on both sides. Now one of the...

I need some information off the tractor but am not near it...I would imagine there is some sort of ID plate on it somewhere with model, year, serial # etc... Can someone tell me where I might find this so I can explain it to someone? Thanks

I've got someone that wants to buy my Kubota BX 2200...It has low hours and many attachments. Problem is, I cannot find a good source for putting a value on it. Is there anything out there similar to how Kelly Blue Book works for cars??? Thanks, Casey

Time to replace it, looks tough to get to, do you have to pull the deck, or pull the floor, neither? I don't see how to reach it, even with the tractor up on stands. Thanks, - Patrick

I have a 2003 BX2200 with 680 hrs on it. I am experiencing a loss of power after app. 20 mins. of operation. I have replaced the fuel filters with no change in problem. I tested the fuel pressure after the second fuel filter and got app. 2 lbs of pressure both static and running. Suspect the...

i have finally sold some junk and am looking at purchasing a tiller for me bx2200 do you guys thank it could handle a 4 foot tiller. neighbor has a 42" for his but i would rather have the 48" if possible. i have looked at the king kutter at tsc just because its local but need to look at others.

I would appreciate some suggestions on where to start looking to track this problem down: BX2200 starts just fine and will keep running as long as the key is in the "start" position. The second I let the key release to the "Run" position, she stops. This started just today with no odd...

Have BX2000 with FEL and MMM . Have done a lot with that little buddy. Hate to part with it. It will be like losing an old friend. But, 4 years old and although nothing wrong with it, I was buying a new Hydro hose for it and saw the new 2x20's and so I traded. Hope I am as happy...

I have a BX2200 with a little less than 400 hrs and was wondering if there is a tachometer made for this machine?

i have been having trouble out of my loader quick connects leaking. i noticed the quick connects have changed to a different style from my bx2200 to the new bx2350. of course my dealer doesnt have any(old ones) and the hydraulic shop only has the new style. that being said i have removed the...

I am trying to plumb a log splitter into the hydraulics on my BX2200 and am not getting the pressures I expected (~1900psi). I tapped into the manifold block behind the left rear tire. This block goes to the front end loader. It has 3 ports: to implement, from implement and return. I used...

While loading the BX2200 on the tilt bed trailer today to bring it home from the dealer, I drove particularly slowly, hoping to take my time and thus pivot and impact the frame more gently. When I dismounted the tractor, I noticed fuel all over the left rear of the trailer bed. I searched high...

Hello, There are 3 wires under the seat of my bx 2200. The one wire I connected a work light too. Another wire has a male connector on it. The last wire has a female connector on it. I plugged the male wire connector into the female wire connector and the hst light on the dash came on. I...

would a 5 foot bushhog be to much? ONLY would be used to mow about 2.75 acres of field ? maybe a 4 foot would be more realistic.

Hey all, i'm new to the scene and considering purchasing a used BX2200 w/ 255 hours, garaged stored. Extras are a LA211 FEL, 60" MMM, and a Befco T30-150 3pt tiller. I'm in OH. We agreed to $8700. Does this sound like a fair price? I'm on 5 wooded acres w/ about 1 acre of grass. Planning...

im needing to remove the floor pan on this tractor seems pretty straight forward but to remove the dials for the deck height and 3 point adjuster(speed) im having alittle trouble. any secret to removing these? something im missing??

This week I tried to dig out lilac bushes for a neighbor after installing the tooth bar on my Kubota. It worked to a certain degree but failed when lilac roots could only be attacked by one side of FEL. What happened was it popped the back end of the tractor off the ground. We ended up putting a...

Several weeks ago, I got the BX2200 back from the dealer after having the Woods BH6000 put on. At the same time I got the new seat, replaced knuckles, and had the mechanical retrofit cruise control put on. The first time I cranked up, I noticed the fuel guage, temp guage, hour meter, and glow...

i have been looking for quite sometime for a small tractor and loader. i was figuring i would have to make a 10 hour drive somewhere when a neighbor cam to me about a bx2200. he has one so i am familiar with the model.( 0.15 )miles from my driveway was a bx2200 with loader 60" deck hardly used...

I may have the opportunity to buy a bx2200, 60" MMM, FEL, with 200-300 hours on it. What would the price be for said beast?

I seem to remember a thread about this but the search feature didn't find it. A friend is having trouble getting the PTO to engage on his BX2200. He said he has had problems with it since it was new but never told the dealer of his problem. His son has lubricated all the linkage that he could...

While I was out of town my teenager ran my tractor out of fuel. Now the tractor will start but will not stay running unless the key is held in the start position where it seems to run fine until you let go of the key. Any ideas? Thanks.

Just today I bought a used 2002 BX2200 (Will be delivered Monday). 508 hours, Kubota snow thrower (good shape, with electric chute rotator), 4way valve, 54" MMM (excellent condition), turf tires, soft sided cab, wheel weights, work lights. Overall the tractor is about a 8 out of 10. Paid $8700...

I found oil filter 15241-32090 cross over= hastings LF523, Fleetguard LF3591, Fram PH 3593, super tech ST3593A this has relief valve, also Napa Gold 1064, I have a cross over book for most filters. hope this helps the BX drivers. Paul.

This is a 5' Cycle Country plow that I attached to the bucket of my BX2200. I cut the push tube and welded on a 2" sq tube. I then welded tabs made out of 1/4' stock to the ends of the sq tubing. The brackets in the bucket are 2.5" angle iron. It's very fast to install and remove in case I have...

I thought I'd pass along the modification I made to my original seat until I can get a new seat. I'll post pictures of some of the work I've done as soon as I can. First picture is my BX. Second is the level of the seat after mod. Third is the difference in the springs, both in length and...

Today I bought a 2001 BX2200 to give to my Dad for Christmas and wanted to get folks opinion on my purchase. The tractor has 400 hours on it, LA211 loader, 60" belly mower, 4' box blade and 4' bushhog. The bushhog is about a year old. I paid $7000 dollars for everything. The tractor was...

I tore up the 3 hydraulic lines that extend out behind the right front wheel. The three lines that are used with the FEL. I downloaded the parts manual from TractorSmart but I could not find the part numbers for the three lines. I need to replace all three lines. Any help with part numbers...

Anyone ever had any problems with this indicator light? (the blue one that will tell you when the headlights are on) I can tell the headlights are on since they shine on the grill guard, but I'm cursed with being extremely picky and would like it to work again. Of course I checked the bulb and...

Anyone ever replaced their sending unit? The part is only $24, and I would sure like an accurate gauge if it's not a PITA to replace. Thanks!

I recently increased my lot size from about 3.5-4 acres of mowing to 6 acres of mowing. 2 acres are well manicured lawn and the rest is pasture field mowing. I currently mow with a 60" MM deck. I'm considering upgrading the BX to a machine capable of handling a 72" deck which I've been told...

Is a 6' angle blade to much for a BX to handle? mainly for snow / ice removal and light grading. any one use this set up? any Pics? TIA

My fuel gage seems to have a mind of it's own these days. It shows "full" when I fill up the machine, then acts "normally" as I use fuel. At about a half tank I can see the needle move to empty and back when on slopes as expected, but it has been showing a little under half a tank when it is...

I have a 2000 BX2200 with 500 hours on it, 60" mmm and FEL. Trading to BX2350 comparably equipped. Dealer has done all the service on the BX2200 so he knows it has been well taken care of. He's saying $7200 for the trade. I'm thinking that's a bit high. Any thoughts? Thanks!

While I was cutting the grass on Saturday, the mower on my bx2200 snagged a big rock out of the ground and got wedged half under the mower deck. I heard some loud rock smashing and then the entire bx shut down. The whole thing lasted less than probably 3 seconds. It happend so fast I didn't...

While cutting the grass on my Gravely Tractor today I managed to get hung up on a spruce tree root sticking up out of the ground. I couldn't back up or go forward without the back wheels digging into the ground. No 4 wheel drive or differential on the unit to help me out. So with my neighbor...

I bought a used 2003 BX2200 and it came with AG tires but I'm thinking for the summer for cutting the lawn the turf tires would be a better bet so I have been googling and found a store in NJ that sells the turf tires in the size I need but I haven't located any seller of wheels for my Kubota...

I am trying to buy a rotary cutter for my BX2200. Owners manual says max 42" and 300 lbs. The lightest I have found is a light duty Bush Hog Squealer at 356 lbs. All others are 400 lbs and above. Other than front end weight, I am concerned about damage to three point hitch and hydraulic...

The main hydro hose to my loader keeps disconnecting itself after raising the bucket to it's upper limit. Anyone else had to reroute these lines to avoid this? This is the Kubota loader, not a 3rd party unit. Also, when this happens the only way I can get the bucket down is to use the float...

I have a 2002 BX2200 with 60" MMM with mulching kit. The other day I was just finishing mowing about 1 acre of wet bermuda where the tractor was obviously working pretty hard ( I had to slow down in areas of thick grass so the engine would come back up to speed) when I drove across my driveway...

After reading the forums on TBN for some time and talking to 2 owners of Kubota tractors, the wife and I went shopping and bought a 2001 BX2200 with 586 hrs. on the clock. The BX came with a Curtis soft cab, 60"MMM, LA211 loader, and 50" snowblower. The dealer we bought from gave us a 50 hr...

Now that outside temps are hitting the mid 90s, my tractor looks to be running hot. I bought it used so i can't compare it to anything in the past. After about a hour of cutting the needle is touching the red on the gauge. If i shut the mower off and lower it to idle the temp falls to just...

After running for about 20-30 minutes at full throttle (while mowing) my tractor starts to die out but then gets back up to full throttle. I have bled the air from the fuel system and refueuled with new gas and this is still happening, Any thoughts on other causes and or solutions? Thanks!

A guy I know has a BX2200 (4 years old, I believe) that he would like to sell. It has a 54" MMM, but no FEL. He has only used it to cut his grass and pull an aerator over his 1/2 acre yard, and it has a grand total of 72 hours on it. He is asking $ 6500 for it, and is firm on that price...

i just bought this tractor used with 500 hrs on it, thought i got a great deal till i noticed the engine using about a quart of water a day. pulled the head and noticed the crack in #2 cylinder. anybody know where i can get a used head? new ones are 728.00 from kubota. ouch!! i found used...

Was out mowing, started smelling hydraulic fluid, stopped and looked under, trans fluid everywhere, all over deck, basically pouring out from some place above the center PTO output shaft (which doesn't appear to be leaking). I'm guessing trans input shaft seal?? Sending it in for service...

I'm not using it enough--though I LOVE it. Almost 4 yrs old and only 100hrs. Have alot of $$$$ tied up in it, and it's almost paid for. But it takes up one stall in the garage, and my truck sits out in the KS hail storms now............. I've finished the jobs I had purchased it for, and...

I was thinking of trading my BX2200 for a BX24 so that I'd have a backhoe but the dealer said buying the Woods BH6000 would cost me a lot less money then trading. He gave me a price of $5500 for one that I install myself. Does anyone have one on their BX2200? I'd like some feedback on this...

OK, I want to clear one thing up right off the bat. I grew up in the city...Huntington Beach, CA to be exact and lived in a 2bdrm apt with my single Mother and 2 brothers, no yard. I moved to the East Coast, made a bunch of money and told myself that I would buy 5 acres of land and a tractor...

I know that it is hard to believe, but I have owned my BX2200 for five years and never checked alignment of the MMM until this weekend. The left front anti-scalp wheel was worn completely flat, the right front wheel was worn about 50%, but the back two wheels were near perfect. After being...

I finally bought a new 60" mmm deck for my BX2200. Unfortunately the owner’s manual was not with it. My Dealer will order one, but I need to get the grass cut this weekend. I think I can take a stab at leveling it without the manual. But if anyone has a pdf file or an E-copy that I can get...

Does anybody know of a full cage for a Kubota BX2200. I'm getting all crippled up and am having problems getting on and off my tractor and it would be helpfull if there was such a thing as a full cage that I could use to pull myself up on and off the tractor with. I fell embarassed asking this...

What is the best way to REMOVE this drive belt?? Mine has a few splits in it, and it's time to replace it. I've got it out of the pulleys, per advice from other members in the forum. I've removed the retaining ring under the deck that secures the main blade shaft. Now I'm not sure which bolts to...

I'm a new Kubota owner and I'm not sure how to get the 60" mower deck separated from the PTO, so I can remove the deck for blade sharpening. I searched through the forum and I didn't see any info on that. Any assistance is greatly appreciated. Thanks.

For some reason my bx keeps shearing the roll pin in the front drive shaft. has anyone else had this problem or heard of such? I can't see how the pin is shearing as the shaft is splined. Thanks for any replies!

I've a neighbor whose 73 yr old father gets bored. He also happens to have a machine shop. After looking at all of your pix of sliders replacing the turnbuckles on the BX series I decided to help with the boredom problem. I bought the sliders for a B2710 along with the pins. Total cost about...

My wife gave me a canopy for Christmas for my BX. She ordered it from Sun Guard Canopies at Sun Guard:If you have a tractor ROPS we have you covered. The first pic is a side shot. Second is one from the front. I had lights mounted on the ROPs that I moved to the front of the canopy. Lastly...

What is the most anyone has ever lifted in a FEL on a BX2200 with proper rear ballast? When I say 'lifted', I mean a good 3 feet off the ground.

I have a man that is insistent about buying my tractor. I told him I would be reluctant to sell it but he keeps saying "name your price". Whenever someone tells me they would be reluctant to sell something, I pretty much forget trying to buy it. My tractor is: 2002 BX 2200 with 650+ hrs FEL 60"...

After three years of clearing land and other misc. work, all of the lights are either broken off or dangling. And the blinker indicator shows that they are on. Wish I were more electrically inclined so I could fix all of this. This little tractor has really done the job and my wife and I are...

Hi, I noticed some fluid dripping from one of my LA 211 Loader hydraulic lines today - the hose with a male end that comes from the "Power Beyond Port" and has a male end that connects into the top Female connector on the Loader Control Valve. since this is my first Hydro leak, I have been...

HI all am I wearing out my tractor by leaving it in 4WD all the time? Brad

Hi When we put in our patio, we had a 2.5'x2.5' square pad of concrete, that is about 6-8"" deep, moved over by our dog kennel, I had thought about digging into the ground so it would lay flat, but it was moved before I could dig out a spot, so now I have a big pad of concrete sitting between...

I started a thread a few days ago on this issue, and don't know if anyone is interested or not, but finished the project last night and everything seems to be working fine. It was difficult, but not impossible. No Leaks !! What I did want to pass along was this, My dealer called the Kubota...

I posted a thread the other day on the coolant leak on my 2200. I got the new water pump yesterday and am planning on replacing it tomorrow. Any advice , tricks, etc.from anyone out there on getting the radiator and shroud out. Dealer says it can be done, but kind of tricky as they don't come...

I am interested in selling my BX2200. It has the 60"mmm and FEL as well as bar and turf tires. It also has less than 80 hours. The turf tires have less than 1 hour on them. What price can I expect to get for this set-up. It is a 2003 model. Thank you.

I have a BX2200 with a 4 foot blade that I want to drag/grade our 100 yard long driveway with. The problem I have is the blade will not dig down but just skips over the top on any compacted dirt/gravel that needs to be redistrubuted. I have seen other tractors that the owners have added...

Hi: This is my first time posting. I have a 3 year old BX2200 4WD that I bought new and have had very few problems with it. I use the tractor mostly to mow with and some small tasks in the orchard. Yesterday I noticed what appeared to be a leak coming from a line connected to the power...

I finally found a place to upload the video, bring on the safety police and the you gonna break it police, and the you can't do that with a hydro police!!! http://www.youtube.com/watch?v=aHEmvPhwu8Y

My starter refused to work. All electrical idiot lights + fuel pump seemed to work all right. I finallly discovered that a "white wire with black stripe" runing from the switch to the starter/solenoid had a discontinuity. If I bypass that wire, everything seems to be fine. Question - is that...

Hello, found this site while doing some research on a tractor. I have been searching around and learned a lot. I found a 2003 BX2200 for sale with a FEL and 60" mowing deck and a rear blade. I think this will do everything I need. The unit has about 440 hours on it and one owner garage...

I'm going to figure out how to post pictures soon...and I'll update them when the Woods 6500 hoe comes in in a few weeks. In the meantime I have a question regarding the proper toolset to maintain my new toy. I want to be able to take the loader and hoe on and off and replace filters as...

my tractor has a grinding noise from the front end when in 4wd and the bucket full of dirt.. anybody have the same experience? the tractor has 500 hrs and i am the original owner. i only engage the 4wd when used on soft ground or heavily loaded.

Hello, I'm new to the forum so go easy on me.... We will be redoing our 2 acres' landscaping starting this month. It will be a couple years project and I may want to take the whole landscaping thing a bit further when I retire, and go into business with a freind who is a lanscape architect. I...

Is anybody actually running the Gator #90987 blade (with adapter bushing for the spindles) in the Kubota BX2200 60 inch deck? I have the bushings, but I see the blades are slightly longer, measuring 20 9/16 instead of the current (stock) blades at 20 1/2, so it's a 1/16th longer. There appears...

I changed the oil in my front axle yesterday. Most of oil drained from the first side that I removed the drain plug from. Upon refilling with oil, I assumed that the new oil would freely pass to the other wheel and equalize. I ran the tractor a little while around a sloping area try to get an...

Was topping off my BX2200 in the shed and there was a little deisel left in the can so I squeezed it all in the tractor, put the cap on and made a mental note to pull it out and drive it a bit. Took the can to town, filled it up and then forgot about startting the tractor and left it in the...

I had a power steering hose rupture on my BX2200 (leaking on top of the mower deck.) I have seen the problem reported here under several threads. I delivered the tractor to the dealer for repair, with the problem identified. After a week of waiting, today I received a voicemail from the dealer...

After the tractor is used for awhile, when I shut off and try to start it later, it sometimes will not start. On a cold start, it has always started with no problem, until today. Would not start Friday evening after using and towing back to the house. Let it sit till morning and started...

I have incountered another leak, this one is the gear box for my 54" MMM. The leak is between the gear box and the belt pulley, has anyone had this problem. Also power steering leak can anyone help me with any recalls on any of these items. Thanks

Hello all, I completed my 300 hour maintenance on my bx2200 this weekend. It took most of Saturday to complete. I do have a couple of questions though. Oil/Filter – 10w30 kubota brand – no problems Trans/Filter – SUDT – easy to do Trans Screen – This was the first time I cleaned this...

owning-ML-894989-ML- Kubota specific thread.

I removed the mower deck on my BX2200 today and the shaft to the front axle was hanging loose from the front axle. There was no connection to the transmission. Obviously, something fell off. I don't know how this could have happened, or exactly what fell off. Any ideas or comments (except...

has anyone found a way to repair the steering hydraulics to keep from having to replace the unit every two years or so. i am on my second steering unit because of wander unless i jerk the steering wheel as i try to keep a straight line for mowing or grading etc. i read someone else had same...

I am trying to solve a trans leak. Does anyone have schematics of the hydraulic connections to the trans? Specifically behind the left rear tire.

My bx2200 starting leaking hydraulic fluid near the block. It looks like there was a relief or drain valve where the leak is. Can someone help me stop the leak?

I have a co-worker who has a bx2200 and was looking to buy a loader for it and he has found 2 locally and he's not sure what to do,I said I would ask you guy's right here.Here's the deal an older style Kubota loader the one the control valve stays with the loader when removed,it is new at a...

I am looking to upgrade my BX2200, so I am wondering if you folks have any thoughts on pricing on the B7510HST w/loader? I have not tried talked to the dealer yet. Here is what I am thinking. They have both of these on the lot. B7510hst with 302 loader. or B7510 turf special with 302 loader...

I already have the redesigned part, I was wondering if there is another redesign to beef this up for if it's just going to keep breaking every 200 hours.. ? Thanks, - Patrick

New to group and forgot to attach schematic on original post. I have a BX2200 I bought used (155 hours-now at 385hours). Water has shut me down each time it rained and the tractor got wet. I drained the filters and part of the tank each time it rained. The stock filters can not handle water...

I'm a new poster as of today but have gotten many great tips over the past 4 years from this forum. A little background, I have a BX2200 with 347 hours on it. I use it to maintain 6.5 acres of SW Virginia property. I was mowing with my MMM on Thursday and suddenly the MM PTO stopped...

After doing all the maintenance on my deck, sharpened blades, etc. There was a vibration. I just thought my blade sharpener made one unbalanced during the lateest sharpening. While mowing (a total of about 20 minutes), all of a sudden there was a very bad noise, so I immediately shut down the...

Has anyone else had a problem of recurrent water in the fuel system? Let me tell you what I do know. I have had the leaky fuel tank upgraded. If I leave the BX out in the rain I will get water in the system. Easy enough to fix, I just disconnect the fuel line,drain the water (usually about 1/2...

how difficult is to change the seal (the one on red) on the front axle, has anybody done this before. thanks.

Still trying to decide what to buy to take care of our new house on what is currenty 4.5 acres of dirt. I fear that I am beginning to get that whole "paralysis by analysis" bug, as I have been "trying to decide" for several months. I have been talking to both JD and Kubota dealers and they are...

I have read the old posts on the old steering problems and the service bullited from 2001. The problem with mine is that I purchased mine in late 2002. Does anyone know if Kubota will still cover this under warranty. It is acting exactly like what is stated. I have to turn it hard to turn...

I've got two issues that are probably related -- first, my three-point control lever is very stiff and hard to move, and as such it does not reset to the center point when the hitch is in full up. Second, after running about 20 minutes I seem to loose power. I'm making the assumption here that...

I think this is ok to post here, since they are a sponsor. I saw one of the popups here for Homestead Tractor ROPS (wouldn't you know it, now the ad is not showing!) I emailed to ask if they offered a folding ROPS for the BX2200 and this is the answer I received: ********** We do not yet...

My '03 BX has only 195 hrs but I noticed the coolant expansion container was low so I added fluid up to the mark and went out and worked for a few hours. I noticed an antifreeze smell a few times and checked to find the container almost empty again. does anyone know of any "normal" places to...

Hi everyone! Spring checkup has arrived 2 weeks left on warranty small leak on shaft mid pto. Is it a big job to fix or what gives? Love the tractor, thanks for input.

Recently "graduated" from a MF 135 to to an '03 BX2200 with 195 hours. This unit came with manuals for everything except the FEL. Is there a source out here somewhere or is someone willing to provide a copy of the pages showing the removal and attachment process? I think I might be able to...

Has anyone disced with a BX? I'm considering buying a 45" 3 pt. lift tandem disc to use for food plots, but want to make sure the BX will be able to lift it and pull it. It looks like the disc may be a little too tall for the short BX, so I would first lower the pins before doing anything...

buykubota-ML-833112-ML- Posted in wrong forum.

I found a used 2003 Kubota BX2200 with the loader, box scraper, rear forks. It has 300 hours on it and looks great. It also comes with a trailer so I can haul the tractor to different sites. He wants $9,000 for it and I think it's not too bad of a deal. But it doesn't have the mower...

Hi guys, I felt compelled to register and ask a question after talking to my local Kubota dealer. I have a 3 yr old BX 2200 w/ a little over 300 hours on it. (extremely nice shape) I really want and thought I was going to trade for a new 2350. After going over my machine that I have...

I understand that some of the new Bx series tractors have larger front wheel tire combinations. has anyone with a BX2200 put larger front wheel/tire combos on theirs??

HELLO, New poster here. I just got home with my new entry into the compact tractor game. a bx2200 with 1100 hours that I paid just under 5k for. It seemed to be a good deal to me. great story here I found it from a dealer on the internet that turned out to be my sister's next door neighbor...

Could anyone tell me if K2561-82140 is also the number of the updated air cleaner support? This is the pn that is in my parts manual and what the dealer has in stock. I've read in some posts that there is a redesigned one available and I don't want to put the same breakable style back on. On...

Has anyone found a golf cart cab that will fit over the OEM BX2200 canopy (sun shield) or is sandwiching it under the canopy the only way to make it fit? What are the dimensions of cabs that you have used in either case. Thanks in advance.

I have a short in the headlight circuit and was wondering if anyone else with a BX2200 has had this problem. There is a brown wire coming from the hl switch and brown wires going to the headlights but the wires going to the taillights are white. The schematic I have shows brown wires going to...

Hi, We just moved to a house with 4.5 acres and a 440 foot long Driveway. I also just bought a BX2200 with 298 hours and a FEL (#211) with a 60" MMM. Our new asphalt driveway was put in last week and I figured I'd use the FEL for plowing snow and gave our old snowblower to close friends...

I installed the snowblower for the winter season today. The question I have is the movable support that holds up the PTO shaft on the blower, does it remain up and in contact with the plastic shield, or do you move it down/ flat when you are done installing the PTO shaft?? Thanks

hi, i have a kubota bx2200 new woods front end loader and 60 inch deck, in Tracy California, (just outside Sacremento) . It was for sale on consignment, but the individual there has lost interest. It will be very expensive to go get it from my home. it was suggested by a fellow member here...

I picked up some new front tires (bar style) for the BX and when I got home I noticed they were 1" wider than the tires that were on it (18X9.50X8 vs 18X8.50X8). Does anyone see a problem with running the wider tire?

Well My BX has started leaking fuel again from the sending unit. How many have had this re-occur after installing a kit in them? I honestly am beginning to wonder just how many times this part will fail. This is the second time for me. The kit part # is as follows:K2561-96140 , priced at a...

Just a heads up for folks with a Bx2200. Mine has about 350 Hrs and has developed a hydraulic leak in the steel supply line to the loader valve where it crosses over the frame. There is a small clamp that holds the lines to the frame. One of the 1/4-20 screws was rubbing on the pressure line...

There is a used Kubota BX2200 in the local paper that I may be interested in looking at, but wanted to make sure the price is reasonable before I called on it. The year isn't listed, but its a BX2200, 29 hours, LA211 front-end loader, mid mount mower, and tiller, for $9,500. I've seen some of...

I had to move closer to my job and was unfortunately forced to down size my property size and the BX as compact as it may be is just too big for me now . In all reality I could get by with a large push mower or about a 38" deck on a 12 hp lawn tractor. So I'm going to try and sell her to some...

looking for hydraulic filter number . Looked under the tractor and couldnt find the number on the filter, must be turned to the top. also does anyone know the fuel filter number. Thanks in advance.

Dad had the tiller (set up to run behind his JD 455, cat. 0). I'm trying to work a deal to trade for the BX2200 (cat. 1). The 3 pt frame on the tiller will hitch up to the BX fine, the problem lies in the pto. On the BX as on most other tractors, the "male" part of the pto is on the tractor...

Have any taken a good look at what is involved to replace the fan belt on a BX2200 OR BX2230? Due to the way the engine is mounted in the machine it looks to me like a Major undertaking. I haven't looked under it but, from what I see the lower sheave has the input shaft attached. Do My eyes...

I am new to this forum... wished I'd found it years ago. Anyway, I am looking at posibly upgrading from my BX2200 (which I love), to a new BX23. 1). What should I get for the 3 year old BX2200 with 54" mmm, front loader 2). What should I pay for a BX23 with bucket, mmm, and bh? Thanks in...

I have a BX 2200 with about 225 hrs. The last few times I have mowed I have had a hard time controlling the tractor. The power steering effort is normal but I have to fight to keep the tractor going in a straight line. Sometimes it behaves normally, other times it requires a lot of tuning...

A couple of weeks ago I was digging with my BX and it quit like it ran out of fuel First thing i did was change the fuel filters i started it and it ran for a minute and quit again , i figured it was just air in the lines so i started it again and ran great the reast of the evening. Nest time...

will start to move forward and will creep, but push on pedal more and hydro seems bog down not the engine (sounds like and acts like when raising 3pt. hitch and holding lever in the up position) there is no problem in reverse?

I have a kind of strange favor, if anyone who owns a BX2200 could measure how high the end of the 3 point arms are in the up and down position, I would appreciate it. I am working on a new post hole digger for a well-known company and one of our goals is to make sure it fits on the BX tractors...

Hey guys, What is a BX2200 w/FEL & MMM worth? It is in excellent shape, want to say the MMM is 54" or 60" and the tractor has 98 hours on it and is in excellent shape. Not sure if they put more than one model loader on the machine but this one is a quick detatch type. Had a customer trade...

Found a used BX2200 with 60" mid finish mower with only 87 hours they are asking $7,995.00. Is this a good deal? KC

Hello, I have a Kubota 70000-73274 engine block heater that I originally purchased for a BX2200. Well, the BX2200 got traded for a BX23 before I installed the heater. Will this block heater fit my BX23? My '23 is coming up on its 50-hour service and this would be a good time to install the...

My BX2200 is approaching 600 hours, used mostly for mowing. However, it has done quit a lot of loader work as well. When I mount my homemade weight bar on the tractor as soon as it is lifted it begins to leak down very quickly. The valve that controls the lift speed, that can be used to keep...

I searched all the threads and still can't find a mention of my experience trying to level the deck, and the manual is confusing. What I am experiencing is that when I lower the deck to my mowing height, it lowers, then the right side lowers more after the left reaches it's limit. Never noticed...

Help anyone? Please? I have a 3 year old BX2200 w/ FEL and approx 450 hrs. I have experienced the usual problems w/ fuel tank, fuel guage sending unit seal, steering failure, etc., all of which were repaired under warranty I spent almost a full day using the FEL to dig holes, uproot bushes...

Bx2200 w/60\" mmm I've been looking on this and a couple of other forums for close to a year now trying to decide on a garden tractor. I still couldn't make up my mind. Well yesterday the guy that did some of the clearing around my house and did my driveway was at my house. He has been cutting...

BX2200 and 72\" finish deck I was wondering if I could use a 72" finish deck on the back of my BX2200. I have a lot of grass to cut (10 acres) and every little bit helps vs the 60" MMM. The grass would be cut regularly so would not be that tall. I know of one I could borrow to try out before...

BX2200 60\" MMM I just noticed this weekend that my deck when lowering it seems to be a bit uneven, in that before it reaches the final drop position, I notice that the left edge of it lowers a bit more that the right during the lowering itself. (a bit crooked in otherwords) When I placed it...

Just a few questions for you guys, I purchased my BX2200 in 7/02 so I guess I am still under a powertrain warranty, do you think that covers repairs to hydraulic hoses. It looks like one is leaking that goes to the power steering, right underneath the floorboard. I tired to remove to...

I have posted on the thread on the bx fuel problem and rec'vd no replys so I thought I would try this route.I have just purchased the repair kit for my bx this morning(new sending unit plastic collar) and have installed it per directions. The problem is that the old sending unit assy had a...

Does anyone know if you can get a filter at NAPA or any other parts place to Replace the Kubota one. Not that i dont want to use kubota filter but dealer is about an hour and half away and i would like to replace it now and dont have time to drive to dealer. IF anyone has a number for one i...

Hi, I have a BX2200 that I bought new in 2003 (last year of the 2200 I believe) with a 60" mm. I use it to mow 6.25 acres almost every week during the summer and to plow our drive during the winter. At the beginning of this mowing season I noticed that at lower blade heights (2.5" or lower)...

I noticed the newer models with backhoes come with a fold down ROPS. This has been a desire of my since first purchasing my BX. It would make my storage situation much better if the ROPS folded down. It looks like the fold down version would be compatible with the older BX2200. My dealer says...

Where can I purchase matching paint for my BX2200, preferably in a spray can? I purchased a can from my dealer, but it had a serious brown tint (yes, I shook it well). I bought an aftermarket can from Tractor Supply, but it had a more yellow tint. Surely, Kubota or someone offers an exact match...

Can anyone tell me if a John Deere 8A backhoe attachment will work on my Kubota BX2200? Not sure how many horses are needed to power this and will its subframe mount bolt up with the proper brackets?

owning-ML-649221-ML- Moved to Kubota Owning/Operating forum.

I am shopping for a grass catcher/leaf vaccum for my BX2200. I mow about 1.5 acres, not heavily wooded. So far I am considering the OEM attachment, Cyclone Rake, Agri-Fab, and Trac-vac. Each has it's pros/cons. I like the OEM PTO drive, but it is kind of small (9.75bush) and costly. Cyclone...

Attached find a picture of the D905-E engine block,The bolt (ref.#220 ) can be replaced with a block drain in order to better facilitate the coolant change every two years. The Kubota part number for this drain cock assembly is as follows:15841-73020 approximate cost is around $3.65 each. I...

I seldom adjust the down speed of the 3PH lift mechanism. I recently discovered that the control is stuck in one position. I have tried lubricant, push/pull knob, and looked for some method of adjust, but no luck. Also, this was the first time I tried to adjust it since having the front cover of...

My BX2200 is stuck in low gear and even after following the recommended pressing of the forward/reverse pedal, its remains stuck. I have rocked the tractor back and forth without any luck. Bypassing the start switch and driving the tractor around in low did not help either. The front wheel...

While at the dealer getting another part (see Lower link bent <font color="blue"> </font> ) I told him I need another front weight because I thought only 4 will fit in the weight bracket. He didn't have to order it because he had some in the back. It doesn't have Kubota on the weight but it is...

The conversation about the BX fuel leak has gotten my attention. My warranty is up next month so I'd like to drop the tractor off at the dealer for any last minute issues. I'd like the fuel tank leak addressed if possible. I've already had the air filter update unless there is another one out...

WOODS BACKHOE ANY BODY HAVE ONE OF THESE WOULD LIKE SOME INFO THANKS

First time this happened - I have a 2001 BX with around 350 hours. This is the first time with any problems. Filled up the fuel tank for the first time this spring and the diesel leaked out pretty fast (faster than a drip). Had to practice the old siphoning trick pretty darned quick...

I was just wondering if anyone made one that would work on a BX. I seen another post in owning and operating were someon posted a pic of a small tractor with one on it . They were mowing a bank simmilar to one i have on my property . I fig they would be too expensive for me right now but im...

Does anyone know where I could find used suitcase weights for a BX2200? I would rather have the weights made for it if possible.

does anyone buy filters other than Kubota? If so what kind and where? I Can't seem to get the same filter twice and worry about getting the wrong one. Thanks

Is anyone aware of a lawn striping kit that would work with the BX2200?? I would sure like to have this look on my couple acre yard, and I mow with a 60" MMM. Thanks for any input. Rook

Does anyone know if there are any cross reference hydraulic filters to replace Kubotas K2561-36990 . Would like to be able to purchase one from an auto parts dealer rather than through Kubota. This filter is for the trans/hydraulic system.

I'm the proud owner of a new '05 BX2230 with a 60" MMM that I'm going to install a Woods BX6000 Groundbreaker-X back hoe on later next week. Saw the thread on the Deere 2210 install and said I can do it too. Reason I got the aftermarket hoe instead of the BX23 was the great deal on the BX2230...

While at the parts counter at my local dealer, the tractor salesperson saw that I was picking up parts for a BX2200. We started talking and before long, he had me interested in the BX 23. (which I was already very interested in anyway) My BX2200 is an 02 model with 150hrs and has the FEL and...

I am started to feel like I’m beating a dead horse here but ……. if anybody has a clue if any of the 50cc units listed in the attached chart would be the same, please let me know. I notice there are three columns that list : 1)relief valve bar psi 2) shock valve bars psi and 3) check valve...

I posted a few days back about a small leak my PS unit had - has. The pump man seemed too slow for me so I picked the un-touched unit up from him hoping to get it to someone else here in town to look at. He said unless he could get a parts breakdown and find out if a seal kit was available that...

Is there a 12-volt connection at the back of a BX2200 that I can connect a sprayer to? If not, where is the best place to get 12-volts? Thanks, jb

How much weight have you had on You Bx's 3 point hitch ? Was this with front end weights? Loader perhaps? I know what the manual says but I would like to hear some of the real figures.

My meter stopped working at 150.3 hrs. I hooked it up directly to a good source and can here it clicking but it does not roll anymore. Shouldn't this thing normally last a lot longer or did Kubota use a really cheap unit? What am I looking at $$ for a good replacement? Thanks.

I finally decided to attempt to fix a very small hydro oil leak coming from somewhere under the steering unit. The tractor is out of warranty but I still decided to take it to the dealer. $108 shot in the @$$. Did get a free wash job, oh that made it all better. He at least knew to clean around...

During my first year of mowing with the BX2200, I used the blower and bagger. It was a lot of work. For the last 4 years I've used the mulch baffles and blades. It functions well in addition to being less work: no bagging, and with recycled nutrients, no fertilizing. I'm going to try to sell...

I have a good-sized former garden spot that is so thick with Centipede grass. I'd like to move some of it using a sod cutter and my FEL. I looked through the Woods website and didn't see anything. I am considering trying to piece something together that might work. I'd like to be able to adjust...

I have turfs on my 2200 and am thinking of going with more aggressive treads for FEL and dirt work. I know there's been a lot of posts about tires, but I'm interested in how wide each of these might be. I like the looks of the turfs as far as width, but would like more traction in dirt...

Hi I am a new member and have been following the forums with interest and have decided to purchase a bx2200 with FEL,mid mower and backhoe for my small lifestyle block. I live outside Los Angeles and am having trouble finding one. Could any one recommend some dealers in or near LA who may sell...

I kept reading the posts about grapples and decided to build a small one for my BX2200. I don’t plan to do a lot of heavy work with a grapple so I made it to suit my needs. When I trim the trees on my place I have a lot of trimmings that I burn and trying to haul a lot of small branches and...

I don't know much about hydraulics, but would a BX2200 be a suitable host for a three point hitch driven splitter? A guy down the street from me has one for sale, and since I don't want to pop $1000+ for one down at TSC, I wondered of anyone has any knowledge of doing this with a BX. Thanks

(also posted in oils fuels) Hi all! I'll keep this simple. I need to go synth because I store in an unheated shed, and I had alot of trouble starting when REALLLY cold. I'd like to go with a WIX filter and synthetic oil. I cannot find the right WIX # for the BX2200. And I need a...

Hi, I'll keep this simple. I need to go synth because I store in an unheated shed, and I had alot of trouble starting when REALLLY cold. I'd like to go with a WIX filter and synthetic oil. I cannot find the right WIX # for the BX2200. And I need a reccomendation for a good brand and type of...

Changed the stabilizer links from the PITA turnbuckles to the telescoping links some time ago, just got around to putting on the finishing touches. They worked just fine the way I had them, this just completes the look.

Just put on my cruise control (nice instructions from Kubota by the way - always good to use your prototype parts for your manuals) And while nothing quite equals the joy of the new lever on my BX, has anyone else noticed that you can't quite set it for the full pedal travel limit? Meaning that...

I am thinking about buying a cab for my BX2200. The central NY winters are getting too much for me. I have been looking at the Sims and Curtis cab literature. Do any of you guys have cabs for your BX and what would you reccommend ?? Thanks, Jon

The 15 amp fuse that is for my gauges and instrument panel lights blows quite often. I replace it and it lasts for a couple of weeks to a month and then blows again. Does anyone else have this problem. The tractor will still start and run without it. Does anyone have a wiring diagram of this...

Under the seat of the BX there is both a male and female exposed connection. The female has power to it. Is the male a ground? I want to hook up one or two Plug-ins (cigarette light type) for portable work lights and such. Thanks Guy

Just finished installing a stepvan heater (part#55-322) 15,000 BTU's $102.49 and comes with 3 speed switch. Total cost came to about $150 with fittings, hose, clamps, anti-freeze, shipping, sales tax. I removed the goose neck & thermostat & drilled & tapped 3/8" NPT in thermostat housing for my...

My BX smokes on start up. I do hit the glow plug for 3 seconds prior to start. Why a large puff of black smoke during start up? Any thoughts? GDaigle

I had previously found a website for Kubota parts where you just entered the part number and you would get cost and availability. Unfortunately I did not bookmark the site and I am now unable to relocate this great website. Does anyone know where to get a parts manual (97898-41281) and a shop...

Is it possible to increase the lifting capacity of my BX2200? I lift alot of moist dirt and it Just doesnt seem to have enough power. Is there an adjustment on the hydraulic pump? Larger rams? Shouldnt it be able to lift a bucket full of mud? Thanks for your input

I plan on using the BX loader and back blade for snow removal this winter. We just purchased a 10 acre hobby farm and need to use the BX for this year only. By next winter I will have my Dad's Ford 640 to do the job. What size back blade? I assume it would be either a 5' or 6'. Thanks Guy

I am looking to purchase a rear blade for a BX2200. I will use this primarily for snow removal. We don't get much snow where I live in KY. Usually never over 4". I can only remember us getting more than 6" twice in my 35 years. Any recomendations on sizes or brands? Thanks

bx2200 3pt won\'t stay up Suddenly the 3PT hitch on my BX2200 won't stay up if I put any weight on it. Any ideas? Is there some sort of check valve in the hydraulic system that could go bad? Charlie

2001 Kubota BX2200 w/cab & 54\" deck with 340 went for $4800.00 on EBAY. This is a claifornia tractor. Isn't that awfully cheap?

Today, I needed something to push some dirt and decided, since I had the steel, to build a small dozer blade for my Bota. I had a job where I needed to move some tilled soil "uphill" to level out a guy's yard. I didn't think he'd appreciate me back dragging onto his sod, so I fabbed this to...

After five weeks at the shop having the Hydraulic Control Valve Assembly replaced My BX came home with what I like others thought to be a sticking Speed control pedal( Travel Foot Pedal) After trying the spring adjustment for the slow to return to neutral, It did not help at all. I then tried...