farm pro 2425

On the right side there are 4 levers PTO eng/dis 3PT raise/lower PTO speed And another long through engage/disengage right beside the 3PT R/L. What is that one for? Mine seems to move back and forth with no resistance or engagement. Also I cannot engage/disengage my PTO with clutch in. I have...

Recently I had issues with my hydraulic pump so I pulled it and got a rebuild kit,(some seals and orings ),but when I put them in the seals are thicker than ones that were in it when you tighten the two bolts adasnt from each other you can't turn the shaft with a wrench, any idea's?

Wish I knew more about these tractors but I dont know much about them! We got this 2425 for super cheap as the hydraulics didnt work. Once I got it home I noticed he had the hydraulic lines backwards, switched them and it started working great. Anyway, started it up awhile ago and hydraulic...

Greetings, does anybody know what the psi setting should be for the injectors in a Farmpro 2425 with a Y385 Engine? Thanks for your help.

Hello ! Does anyone know off hand or have a diagram showing if the supply to the loader valve comes direct from the pump and the return from valve goes to the diverter valve or do I have that backwards ? Thank you

I have a 2007 Farm Pro 2425 4wd with the Y385 diesel engine. My issue is that I do not have any fuel going to the number 2 cylinder. I cleaned the fuel tank sediment bowl, replaced the fuel filter. The issue is where the hard lines go to the fuel injection pump. I went to bleed the hard...

Seems to be a rash of steering problems on here lately. I know the steering cylinder is shot because it leaked and, when I toook it apart, the ram is bent and the nylon seals are shot. Like a lot of other folks with steering issues, the steering wheel would turn and turn so I am assuming the...

Hello I have been doing some searching and reading on the topic. Can anyone point me in the direction of the valve they used and how they plumbed it? I was ready to buy the ranch hand kit but unfortunately they do not have a valve source at this time. On keno tractor they offer a valve upgrade...

Good morning, I have developed a pretty fast leak that Initially appeared to be coming from The steering box at the bottom of the steering shaft. However Now the steering shaft is leaking from the top as well, just below the steering wheel where the rubber boot is. I was hoping maybe it was just...

I just purchased a Farm Pro 2524 and have the opportunity to buy a Spirit SL-15 loader for a good price. It includes the right mounts (no bolts) and joystick controller. I cant find anything online for spirit loaders in Waupaca Wi and the phone number I have for them goes unanswered and...

Hi, new to the forum, and dying to get some experts to weigh in on my problem. I picked up a non running Farm Pro 2425 a few weeks ago. I don't really have any experience with tractors or older diesel (mechanical injection) systems but I thought I would give this a try. The fractor is a 2004...

Good morning ! I purchased a 2006 farmpro 2425 from a friend with the farmpro or jinma loader and backhoe. Its my first tractor and I am getting the hang of using it. On the bottom of the backhoe valves there are tiny weep holes. One of the backhoe motions and one of the outrigger stabilizer...

I have a 2425 and need to remove the FEL to get to the clutch inspection hole. My Clutch is constantly engaged and I need to know how to remove the FEL can someone assist me? I put the center bar down and have been rocking the tractor back and forth to no avail. What should I be doing to get...

Hello everyone I am new to this forum and have a question about a 2425 clutch which stays engaged. The clutch petal has no resistance, it was working fine them slowly it became non responsive. I was wondering if anyone had experienced anything like this before, I want to know if you think the...

Once again I come before you hat in hand with an abundance of ignorance and little else. I have a Farmpro 2425 tractor which has been great. Recently I have been having problems with it. I had an overheating problem so I replaced the theromostat, this seemed to fix the issue. Then I has an...

So I bought this little tractor with no attachments thinking they wouldnt be expensive. I really just need a loader for moving stuff around the property... anyone know where I can get the front loader attachemt? Also, are there universal attachments or are they all brand specific? Thnx in advanced

First time post and I am not super mechanical but I get buy. I own a FarmPro Tractor model 2425 and my backhoe hydraulic seems to be disengaged. I would like to move the tractor into our garage but I am unable to lift the stabilizers or Backhoe boom. Any suggestion how to bypass the hydraulic...

Can someone tell me why I have to turn my steering wheel about 10 times to get it to make a full right or left turn while driving straight? I know it works off the hydraulics, so could it be a weak pump? meanwhile the FEL works as it should???

Tractor is about 10 years old. Right rear wheel has locked up. Left will turn. Never had this problem before. Any ideas why

Hi, First of all im sure I am not the first to post about this but I cant seem to find the info. I have trans fluid leaking into my break hub. I have stripped it down but im not sure where to go from here. All i have now is the shaft sticking out that the disk brakes run on. I took the snap ring...

Hi all Farm Pro 2425 Engine Y385T Have a Napa oil Filter L14619 that is on, this cross references to a NAPA 1626 and it is just too big. Went back and got a napa 1381 and it is closer but still no go. In my old reference it says: New style: NAPA 1821 and old style: NAPA 1452 Any idea on...

My fuel bowl is shot on my Farm Pro 2425. I tried fixing it but it just broke. Is there a part that will replace these without having to order one? I have a couple tractor places around here but none carry Chinese tractor parts. Thought maybe someone here may know of a different brand that would...

Newbie here. Great forum by the way. I've had the steering wheel keep turning problem for a while but it steered fine, but yesterday the steering got downright hard to steer. If i turn to lock one way I can't hardly get the wheel to turn back. I searched but couldn't find that exact problem...

I'm considering a 2005 Farm Pro 2425 that is a reasonable distance from me. 4x4 model and they say it's all works and has manuals. 712 hours. Mower not included but I don't need a mower. Is $3,500 a good price? Looks like it needs a little cleaning.

Hi I am looking to sell my Farm pro 2425 it is a 2006 3 cylinder diesel 4x4 with aftermarket cab, it has approximatly 900 hours with a new clutch just curious what would be a fair price, there is a picture of it on my profile thanks Mike

I have a farm pro 2425 with FEL that I'm having some problems with blowing the hydraulic pump (2 gone in a year). It started last fall suddenly locking up while using the FEL, It would lock up and stop the engine with a loud clunk. The 3rd time sheared the hydraulic pump shaft. Ordered a new...

Hello all, I have a Farm Pro 2425 and am trying to replace the oil seals and felt washer in the standing shaft section of the front left wheel. I finally got the housing for the bearings/seals off and can see where the 2 oil seals are but they are not budging! I've taken pliers to them and tried...

I need to change oil in my Farm Pro 2425 but can't find the drain plug, It's not where the manual says it is supposed to be. Any ideas?

While doing ground work it developed some hydraulic fluid leaks. The hotter it got the more it leaked. . Two of the leaks were two missing plugs on top of rear axles. I plugged them with bolts. I assume these were to bleed air out?? My main problem is that it's leaking out the bottom of...

While using the 2425 today moving dirt I had several leaks develop. I found a hose fitting that needed tightened near under seat, bottom of steering looks like bolts need tightened and two on top of rear axles. I've got the hose leak stopped, still looking for wrench size to fit steering bolts...

While using the 2425 today moving dirt I had several leaks develop. I found a hose fitting that needed tightened near under seat, bottom of steering looks like bolts need tightened and two on top of rear axles. I've got the hose leak stopped, still looking for wrench size to fit steering...

Hello everyone, This mower was bought 4 years ago and it has always been hard to get it into "gear" to mow. In fact I just turn it off, engage the pto and the start it back up so I don't hear it grind. I don't know anything about these tractors and neither does any repair shops close to me. My...

Going to look at a Farm Pro 2425 that looks almost new in pictures. It's a 2005 model. How much is it worth?

I adjusted the clutch last fall because I couldn't get pro to engage from the neutral position. It would make a grinding noise and not engage. After adjusting clutch it now engages fine , but when speed selector is in neutral the pro shaft keeps spinning. Is this a clutch fine tune related...

I've let tractor set for close to 3 months. I started the other day and noticed the 3 or hitch not raising? It was working good before. I haven't vhecked fluid yet, but is there something else in missing? I did adjust the main clutch after having trouble getting PTO to engage if that has...

I have a 2004 farm Pro 2425 that's not wanting to crank. What's the best way to check soleniod and that it's getting the electrical supply it needs? It had acted up before but not sure if connection problem, key switch or soleniod itself? Also what it the small push button switch that the...

I have a 2004 Farm Pro 2425 but I cannot identify the correct part #'s for standard maintenance items i.e. Air, Oil and Fuel filters etc. Does anyone have those part #'s or direct me to a site that can help identify or order those filters?

Hi guys, hope there's a simple solution to my problem.Just got the tractor and the pto works, but can not engage with engine running. It just grinds the gears. I sure don't want to damage anything. Is there some kind of throw out bearing not working or is this how they are? I've tried different...

I've noticed the only gauges that are lighted is the tach/ hour meter & the horn switch. It's no biggy, but are they supposed to be lighted? Or is this how they came. The other gauges have a hole for a light, but looks to be covered.i don't see any loose sockets to put any bulbs in. I took the...

Found a Farm Pro 2425 with 211 hours. It's in vgc starts easy, runs smoothand comes with a 5' bush hog. Only problems is hood latch , leak in top radiator hose and bush hog drive shaft needs a yoke bearing. In looking for an idea on value?

Hello to all the members. This looks to be a great forum. Just bought my first diesel & first 4wd Chinese tractor. I'm still trying to figure out all the levers and doing some minor service & repairs.

All- Any idea why when I had my steering cylinder rebuilt on my farm pro that I no longer have steering? Could there be an air bubble in the line that does not allow me to steer? I took the steering diverted off the tractor took it apart and it does not appear to be plugged up. Thanks for any...

As the title says I cant get my lift arms on the 3 pt hitch to rise very far. Ive got a tiller on the back and I can just barely get it off the ground. I'm not sure how high these things go but it seems I should have a bit more lift than this! The lever next to the seat is leaking fluid around...

I recently bought a used farm pro 2425 with FEL and a Backhoe(same as the Jinma 254?)(this is my first tractor)with 400hrs on it in December. I got it to the house and ran it a couple times the first week. Then the weather set in. I have it parked a couple miles from my house and it seems its...

So I just split my tractor today to address the leaking gasket between the sump and flywheel housing. It went pretty well, minus a few minor hurdles. Ive got it stripped down to the gasket, there was basically nothing left of it! A few of the larger bolts holding the flywheel housing to the...

More fun with my 300hr Farmpro 2425 (jinma 254). I was bathed in hydraulic fluid spewing from the junction. I seem to be replacing these often (different ones though, not the same). Is there a longer lasting solution? I fear these will fail again.

Please delete figure it out

I parked my farm pro 2425 in the barn with no problems. My goats got out and were climbing all over it. Now the clutch pedal is very loose. You can move it very easily with your hand and it grinds when trying to put it in gear. I'm not a mechanic but thinking its something minor since it worked...

I'm a newbie to this Chinese tractor thing.. Can any body lead me to a good manual/operator manual for a `06 Farm pro 2425 Y385 4wd. I need to know everything about this tinker toy. The unit came with a "Homiers" operators & maintenance, parts list and engine parts list w/engine operation...

Hi, i have a buddy that is looking to buy a compact utility tractor for running a brush hog on some property he bought to hunt on. He found a Farm pro 2425 4x4 used in great condition. The weight of this machine is 2700lbs. If the 9.5x24's were loaded could he pull a 2 bottom plow? I've...

Trying to help a neighbor fix his ride! He's convinced the motor is locked up and is on the fence to go buy a zero turn and turn the tractor out to pasture. I thought I would lend a hand, but unfortunately it appears this won't be simple and I am now in learn mode. So, it is a FarmPro 2425...

I fill the hydraulic fluid, start the tractor and the fluid fills the crankcase somehow to the point that it runs out of the engines vent tube. Any Ideas?

Where do I find a dip stick or site glass for checking hydraulic fluid?

Hey guys I dont seem to be charging anymore on my farm pro 2425. I thought it might be the battery but not sure now. I took a meter and with the tractor running I put the leads on the battery terminals and only shows a little over 10 volts. I also touched the biggest wire coming off the back of...

So I'm going through my heating issues noted here http://www.tractorbynet.com/forums/chinese-tractors/266032-farmpro-2425-jinma-254-hard.html and I found some rubber components that need replacement. One is the connecting boot on the drive shaft cover and the other is the steering connecting rod...

Hey guys, Thanks for all the past advice and help with my Farmpro 2425, but you know the journey never ends. See this thread about my purchase and adventure: http://www.tractorbynet.com/forums/chinese-tractors/221022-look-what-i-got-1700-a.html Michigan is starting to get pretty cold and I...

I have a Farm Pro that had about 30 hrs. before I parked it about 5 yrs ago......so I decided to put it back to work, so I bought a new battery hooked it up and it fired right up, worked it for about 10 minutes and it shut down so I figured it was some bad fuel so I drained the tank and refilled...

Just picked up my first tractor a Farm Pro 2425. I want to thank everyone for some great information on this forum:thumbsup: Look forward to particiapting Here's my feeble attempt at removing palmetto from the central Florida sand 5 minutes after taking it off the trailer. I have a new...

Looking for an exhaust/muffler for a FarmPro 2425. Any one know a reasonable priced place to purchse?

My 2425 is acting a bit strange; it starts great, but only runs abut 20 mins and then acts like it's run out of fuel and stops running; that's not the case the tank it 3/4 full; any ideas?

hey guys, ive got a farmpro 2425 and its a 2005. i have been told its same as the jinma 200 series, but correct me if im wrong. ive been having starting problems and thought the engine had finally seized, but such is not the case. everything tested fine, and i was able to drop the clutch and...

Hello, I have a friend who owns a Homier Farm Pro 2425 tractor and is needing a couple lift arms for it because he bent them (the arms with the balls on the ends). Where is the best / cheapest place online to buy parts for this tracrtor? Also, I know that it's a Jinma diesel tractor. What...

I bought a used 2003 Farm Pro 2425 with no manuals that has been sitting idle for about a year. I replaced the battery and starter, drained the fuel and added new fuel, cleaned enough varnish/gunk out of the bowl and copper screen to choke a horse, replaced the fuel filter, pulled the primer...

Hi I am looking for a loader for my Farm Pro 2425, this tractor has a aftermarket cab I live in Prince Edward Island canada if you could provide me an quote with shipping included that would be appreciated thanks

i kinda know you all have said numerous times on here that the altenatoes are cheap and go out quick i think mine must be bad but tell me this is there an easy way to check it? why is there no big wire from the alt to battery? what alt would i need to get to replace mine? thanks in advance for...

Hello all,I bought a 2002 Farm Pro 2425 with 71 hrs. it will idle but that is all. Will not throttle up.Thanks for any help.

Does anyone know where I can get a front end loader for a Farm Pro 2425? I live on the east coast of Canada and the cheapest I can find one locally is 5199

Hey all new to this forum and to tractors as well. My wife and I bought our dream home in the country two years ago and ive got 53 acres to play around with and approx 2 1/2 acres around the house that is an ongoing work in progress. Needless to same I learned pretty quick that a tractor...

Anybody know where I can find a dealer in Oklahoma that carries injectors for this model? Thanks for help. Ken

I've got a reatively new tractor (72 Hrs.). Changed oil and put on new water hoses. Brushed hogged for a couple of hrs, noticed engine starting to overheat. Parked tractor so I could work on it next day and hit almost 3 weeks of bad weather. Tried to start today with no luck. Checked fuel lines...

Howdy! This is my first post here.... I have one of these Farm Pro 2425 tractors for several years now. Every now and then, I will snag the muffler's long exhaust pipe on a low hanging tree branch. As a result, the muffler sheers off an inch or two above where it is bolted on to the pipe...

New to this whole thing but this looks like the place for help. I have a Farm Pro 2425 which I understand is a Jinma 254 knockoff. The tractor has just 27 hours on it, guy bought it and it was too small for his construction business. It does a great job for what I need but the three point drops...

I have a Farm Pro 2425 and when i lift the 3 point with my brush hog hooked up I have a hydraulic leak. On the right side under the seat(the right side as your sitting on tractor) there is a hose which i believe they call a banjo fitting on the end.It has a bolt going through it and hydraulic...

I bought this Farm Pro from a friend i work with and it has 110 hours on it and he has never changed any fluids in it.He knows nothing about it and i am trying to learn.It came with two extra filters so i want to change the fluids but i have a few questions.I have read allot on this sight so i...

I seen a thread on here the other day about when turning the steering the steering wheel keeps turning even though the tires are as far as they can go.Now my farm pro 2425 is doing that and cant find the thread again.Does anyone here know what is the problem that causes that.It steers fine but...

Hello all,I am kinda new at having a Chinese tractor so i am sorry if this is a stupid question.I just purchased a farm pro 2425 from an individual that also knew nothing about it.I have been reading the manual because i am going to change the fluids in it since there is 110 hours on it and...

My bulbs on my brake lights are blown.the number on the bulb is QT12-21/5A which only comes back to a few chinese links.Anyone here know what bulb number i can use for these or am i going to have to order these?

Hello,This is my first post here.I just bought a 2003 farm pro 2425 from a guy i work with.He very seldom used it and don't know a thing about it.I have a weired problem with it in the electrical dept. I was checking the lights and blinkers and stuff on it and couldn't get the rear work light to...

I was wondering what this would be worth? It has 180 hours on it,detachable backhoe,comes with auger,box blade, scrape blade and an older bushhog. He wants $7000 for it. any thoughts?

Hello all: I have a couple of issues. First what is the easiest way to get a FEL (FarmPro) off the Farm Pro 2425 tractor? Second rear engine oil seal. Do I have to break the tractor in two to get at it? Is it behind the flywheel? Or can I get at it through the oil pan? Many, many thanks in...

Found another dealer whom claim the clutch linkage needs adjustment, the throwout bearing is screaming at the top of the engagement. Anyone familiar with how this done? I have no printed manual, not even sure any is available.

Got a new 2425, 25 hp, 4wd, 55 actual hours of run time; clutch throwout bearing is screaming at the last couple of inches before the final drive is engauged. Did the search of related subjects and found it seems to be a common occurance with this model to have clutch problems, dealer swears...

Well I think I did it. Trashed the clutch on my 2425. I was brushing a food plot for deer and tried to push over a small tree. There was no noise indicating a major failure. I put the tractor in reverse and it just wouldn't move. Tried all the obvious. Checked the Hi/Lo levers 4WD levers...

I have a Farm Pro 2425. I was using it on Saturday and fluid started spraying out from under the steering wheel. I believe it's hydraulic fluid. Has any one had this happen, or know how to fix it. The hoses are all tight.:D

can someone tell me in English how to set the float position on the 3 pt hitch. I also want to change out the hydo fluid but can,t seem to locate a drain plug. This is the last newbe question for the day----the handle jabbing my right calf is the PTO engage-desengage [I think] If I want 540 I...

When shifting the gears should you come to a complete stop and select your gear or can you shift on the go. a friend of mine just got his tractor today and was trying to shift it like a truck . is this wrong or right.

A friend of mine just bought one , he got it without a backhoe but got a koyker FEL. He plans on adding a backhoe when he gets over the tractor purchase. What is the best backhoe for this tractor . is there any with a subframe .

Hey Folks! Happy Holidays! I bought a six foot scraper blade (farm pro brand) for the 2425. Problem: They didn't give me the two upright braces that go to the top point to the 3 pt hitch to the frame with the other two 3 pt attachments.The place I bought it from went belly up. I didn't...

I have a problem. I got my 2425 stuck clearing trails. I put in in 4WD creeper no go. I locked the differential and got out O.K. Now when the left front tire is straight, the right front tire is turning to the right. I know you are not supposed to try to turn with the differential...

Got a problem with my 3 Pt. the arms are stuck in the "up" position. No amount of "persuasion" can get them to budge. Any ideas?

I am looking to buy my first tractor so please bare with me if ask any dumb questions. My needs are to maintain about 9 acres around my house. I am looking at units with a FEL, box blade, and brush cutter. A local dealer (central florida) is offering both of these models for sale. He stated that...

was mowing today with my 2425 with 18 hours on it when all of a sudden the engine acted if dieing and then would go again . this continued for about 3 minutes, all guagess were good and had good fuel. sounded like a fuel problem to me so i shut if off and low and behold the sediment bowl under...

It seems im losing my power steering on my 2425. At times it gets really hard to steer and it even locks up sometimes. If i turn the steering wheel back and forth it seems to free up the steering until the next turn. Has anyone had a similiar problem. Would this be bad rack and pinion? or the...

I recently purchased a pto wood chipper and it states to run at 540 pto speed only. Does anyone know what the true 540 is ? Idle, half throttle, or full throtte? My lever is in 540.It seems that it doesnt perform well at idle speed (chips just barely shoot out). Half throttle peforms well but...

I wish it had a wider stance. When I first got the tractor, I rolled it using the FEL. Mostly because of inexperience. No damage done to it or me. Soon after I turned the wheels around to make them wider. It seemed to help a little. Now, 100 hours later I find myself wishing I had fatter...

i just recently noticed that going up any incline it seems the clutch is slipping (smells). does anyone know what step i should take next before it gets too bad. if i need to replace the clutch how do i get to it? hopefully its just an adjustment. the machine has 130hrs on it. any info would be...

Hello. As mentioned, expecting my new 2425 to be delivered tomorrow! I have picked up alot of great info from the threads here. Got the Farm Pro to manage 5 acres. It is all on a hill side, wooded. We are in the process of building a horse barn. Will be using the tractor to clear bush...

does anyone know anything about m-mtractor in montpelier, ind. ? they have 2004 fp 2425 4x4 for 5999.00. does tha tseem reasonable? are there any hidden costs?

Can anyone tell me where the steering by pass valve is located on a FarmPro 2425? Mine tractor suddenly developed a quirk that requires me to <font color="blue"> </font> keep turning the wheel to maintain the tractor on a straight path. This tendency is much more pronounced if I am mowing on a...

Does anyone have Fram filter numbers for a Farm Pro 2425. The oil filter that came with the tractor is longer than the original so you have to drop the power steering lines to get it on. Thanks,Billy

Where do you let the fluid out at? I know where the fill is, but havent seen the drain. Also, where is the screen you are supposed to clean out? Any pictures would be awesome. This is the last thing I have to change for the break in. I now have 30 hours! It has been worth what I spent so far!

I made a post a week ago about my oil pressure being low. I do think the stock pressure guage was all wrong, and I replaced it with a sunpro guage and copper pressure line. When you first crank it up, the pressure is almost 50psi. As it warms up, the pressure at idle goes down, but the rev'ed...

Post deleted by Travis_R

Hey ya'll! My name is Travis. I am 19 yrs. old and Love tractors. My friend has a Farm PRO 2425 tractor. I put 7 hrs. on it today with a 6ft. box blade. I need answers to the following questions ASAP before the tractor gets tore up because of lack of maintenance, adjustments, or non-awareness...

Hi, still new to all this, how do I know if there is enough oil in the injector pump? There is no dipstick on the vent/fill cap. I know it takes 30W. Thanks!