bobcat

I have a 2015 Bobcat 418(now called E10) with a leaking expansion tube. Does anyone have any tips on how to pull that piston? I have scoured the internet and the manual and cannot find anything. The expansion tube is the piston under the machine that expands and contracts the tracks.

I just bought a used 2015 84" Bobcat soil conditioner. Big purchase for me, and it is working really well with one issue. All functions work but the right to left cylinder kind of feels like it sticks as it goes through it's travel but it does go from right to left all the way. But while the...

My Bobcat 325 Mini excavator has lost all function on the right-hand side, I have tested the relief valves, and the hydraulic pump, everything seems fine. looking for ideas to check next

I have a bought a cement mixer for my bobcat that did not come with the male electrical plug that plugs into the external electrical auxillary plug. The cement mixer has 4 wires feeding the relays that operate the hydraulic mixer drive and the dump gate. Has any body else wired one of these...

Hi everyone, I have been looking through the forum here, but there is a lot to search through. I purchased a Bobcat CT2040 with FL8 Loader last year and the BH76 backhoe attachment. I opted to install the backhoe myself to save some money, but I am not a hydraulic or diesel mechanic. Despite my...

Hi, 2001 bobcat 331 excavator , hose that operates boom swing burst, it’s the hose that operated the cylinder under the floor plates. Replaced hose, bled cylinder , now the boom will not swing left to right, everything else operates as it should . First time owner and I’m stumped. Any help would...

Hi, I’ve got a Bobcat CT230. The mid mount pto will not disengage. The lever by the output shaft won’t move. Any suggestions before I drop the pto unit? Thanks, Tim

I have an S130 Bobcat. I want to get a snowblower for it but not sure I have the right connections. I know you need to determine if it’s low flow or high flow. And the snowblowers I’ve looked at have and electrical connection and my Bobcat does not. See attached photo. Do I have 3 hydraulic...

As the title says, I have the CT335 (2010) which should be the DK35....long story short, need to split the tractor to get the oil pan removed (unless someone knows how to do that without splitting, I don't see a way), I'm at the propeller shaft and the instructions are very basic: 6.1.5...

Just curious as to what the opinions are on Bobcat.Tractors! Who has owned one and the pros and cons.? I'm interested in a smaller size....under 40 hp.

If you have a CT450 tractor and are having a tough time finding parts, I have figured out my cabbed CT450 is essentially a re-badged Kioti DK45SE tractor. It seems the folks at Kioti are much more helpful when trying to cross reference parts look up for me. I have found that Michigan Iron &...

Which tread pattern do you recommend? I'm in Illinois and mainly use my T650 around the farm. Terrain is dirt/mud/grass and I use it to clear snow. I was looking at these two options. Any thoughts on which one is best? T650 Zig Zag Tread Pattern T650 Multi Bar

I have a Bobcat CT235 with 700 hours. I have replaced the glow plugs in the last 2 to 3 years. The tractor is hard to start no matter the weather. When it is cranking and when it first starts up it smokes a lot, and i mean a lot! After it starts and the tractor starts warming up the smoking...

I have a ct440 ser number abhe11076 i have read all the posts and have not solved problem ran tractor one day would not start next day positive battery post had burned off? repaired and still no go took to bobcat dealer in hattiesburg ms for repair. they said the fuel stop solenoid...

Hey! got a 329 mini ex, machine will crank all day but will not fire up. checked relays and got good ground/voltage but missing the signal voltage to relay. have load tested power on connector J4 pin E and load tested grounds on connector J1 on pins G&D. controller is just flashing 0000 when key...

Asking for a buddy. He bought this used and had nothing but problems!. Yesterday he brought it down to work on it in my plow barn, after he took it off the trailer I guess he shut it down. The problem now is the relay blew out he replaced it with a new one and turned the engine over but it...

I’m just curious if this product is GL-4 or GL-5

This is dumb...but I've had the headlights out for a few years. I can't for the life of me figure out how to put the bulb back in! nothing in the manual and I'm not finding a diagram anywhere. Anyone have a picture? I have all the pieces...just zero memory! Thanks

My bobcat 331E is showing a code of 3-10 high battery voltage. What do I do?? Where should I start. I just replaced the alternator and I am getting 14.44 volts crossed it.

Been a long time since I posted, have plenty of does and don'ts for a Bobcat CT230 if any body has any questions. Having said that, does anyone know what the part # is for curl cylinder seal rebuild kit is by chance? Have a Bobcat 763 and a John Deere 2955 if anyone has questions, happy to help.

It was time for a fluid change on my V723. No problem right? Drained the tank, pulled and replaced the filter, refilled with new fluid. Afterwards, the boom functions and steering all work as expected, but it will not drive forward or reverse. Doesn't even attempt to move. It was driving...

I have a 763 Skidsteer and 1 side of the Bob Tach plate is out of round. I have a new bushing for it, usually that just sits in there and holds the pins that attach to the loader arms. My question is should I weld the new bushing in place to keep if from moving around? Any other ideas? I...

I have a Bobcat B250 - was doing some digging and trying to pull a tree stump out. Herd a noise and then my rear wheels lost drive. Front wheels still have drive. Anyone know what would stop my rear wheels from getting drive? Does this tractor have a chain drive? I see some skid steers...

Newbie. No service manual. Left lift cylinder started squirting oil after lifting loader bucket full height. Purchased seal kit from dealer to rebuild cylinder. Removed gland nut and rod from cylinder barrel. 1.5" socket, 1" drive 40" breaker bar with 36" steel pipe extension was able to break...

Was mowing today for a few hours, and all of a sudden it quit cutting, it seemed to be trying to turn but looking underneath I could see a spark like at the clutch area under the engine when it was switched off. It spinning but belts aren't tightening up to spin? Clutch? Bobcat Procat RS KAW...

The only solenoid I see in the repair manual is the system bypass solenoid. I unplugged it and the code did not change. If I have the right one I am thinking it must a wire shorted out. Does anyone know if this is the right solenoid and what ohm reading the coil should have? Thanks.

Leaking hydraulic pressure sensor. Replaced x2 Now leaking again after only short usage.

I'm trying to replace a leaking high pressure hyd hose on this machine's hydrostatic cooler. I can't get the fittings to break loose using standard wrenches. Anyone have any suggestions for getting hyd hose fittings to break loose? There is very limited space in which to work and wondered if...

I have a 1999 bobcat 331 with hydraulic trouble. The boom lift cylinder drifts so bad I can't use the machine. This is the only circuit affected, I'm thinking I can rule out pump trouble. I can pick it up under extremely high rpm but immediately falls to the ground. The cylinder was rebuilt a...

I have a bobcat 430 excavator SN 563012165. It has been parked under a shed for the past month. Went to move it over the weekend and the only hydraulics that work are the blade, swing boom, and auxiliary. It is showing codes 002-17 & 005-14. I pulled the filter and everything appeared clean...

Hello, I have a Bobcat 331 and while traveling the skew or the boom wants to drift to the right, It will not hold center while traveling. It will not drift left.. if you swing it left and stop it stops right, if you swing it to the right it take is a little while to stop. If sound like it a...

My 331 over the last year has had some starting then stalling problems if I start at three or four times it keeps running, it said a code for fuel shut off solenoid shorted to ground I clean some corroded wires in the engine harness I found corrosion in the ignition switch thought it was fixed...

I might be getting a Bobcat M600 electric skidsteer? Has anyone ever converted one of these to gas? If so what engine is suggested? What all is involved? Cost? Is it worth it? Anyone have the specs on the electric motor? We have 3 phase 208 voltage at our shop (just to try it out). I haven’t...

New community member here. I have a 331 looking for some advice or experience using a forestry mulcher on it. I spoke with Fecon for their 28" and they said it would not work. Torrent says their 28" will work. Does anyone have any experience with one of these brands or with a mulcher (not a...

I recently purchased this tractor and I'm looking for a soft cab for it. I just need the cab to keep the snow off of me. Hard cab is available for +/-7000 bucks and it includes AC, heater, etc. Don't need that. Anyone have info on a soft cab for this tractor?

I have a 773 Bobcat SS. The auxiliary hydraulic control lock only works in counter clockwise rotation. Is it suppose to work in both directions? I need it to lock in the opposite direction. Any help is appreciated.

Does anyone have a service manual # 6902745 for the Bobcat 325 excavator that they are willing to part with?

I finally got my skid steer! After months of searching on boomandbucket, eBay, and the auction sites, I found a decent deal on a 1987 Bobcat 642B. I even had it delivered. While I would have preferred a diesel-powered skid steer, I ended up with a gas one. It will actually be easier since all...

Can anyone recommend a source for a 12" bucket or 9" bucket for the Bobcat 7TB backhoe? It is a rebranded Rhino 75C that isn't made any longer. I believe the Bobcat number might be 7166939. I do have the specs for it but have come up empty in trying to find one or one even close. Thanks...

Just installed a thumb on my Bobcat 325. Need to lower the pressure. Where is the adjustment located? Thanks

Hello all, just a bit of background, I’m a contractor that mainly does outdoor framing(decks/fences/garages) and some residential landscaping. I currently have a mini skid that I built, and it be been mostly good for what I need but I’m wanting more lifting capacity. I’m about to pull the...

Black Friday is 8 days away And racks usually go out of stock around this time of year. So we want to give you a chance to cut the line and order your rack before the public. So we've opened up our Early Bird Black Friday sale for TBN Members! ORDER YOURS HERE SAVE 15%!

Hey guys, it has been a while since I've introduced some new Wickedness to TBN. This product has literally been in development for over four years, and we're now 100% confident that she's ready for whatever. After making and testing many prototypes which were as good as the competition, but...

Let's just say things happened, just can't have nice things and now I need a new bucket curl cylinder for a bobcat ct2025 with the fl7. I'm not sure how to measure to get an aftermarket but if I can figure it out I know it would be about 1/4 the price of bobcat, also my local dealer isn't great...

I have a 2020 5600 toolcat and the wheels are stuck out of alignment and wont go back but it does still drive. Has anyone had this problem? no error code I dont think. Edit: Got to work this morning and it gave me no issues and worked just fine. Still have no clue why it did what it did.

We almost never have any discounts/coupons/sales, but heeeere we go! www.(Temporarily blocked due to reports of company closure) Travis

So I've tried adjusting the machines sticks to deal with the problem but it made it twice as worse, so if anyone knows what the name/ parts required to fix creep are I would be much obliged 2000 Bobcat 763G s/n:512258650 Contact me at 530-708-7548 (please text)

I have a running Bobcat model 980 with over the tire tracks. I think it's an 87' model, it has the Cummins 4bt engine which starts easily and runs well. All hydraulic cylinders were recently rebuilt by Central Hydraulics in Fort Smith, AR. It moves around as it should but the controls are quite...

First time changing my oil in my CT2025 and want to make sure I get it right. Does 3 quarts of 10W30 sound on par? Also anyone know the filter part #

I have a 2008 Toolcat 5600 that wont move. When I lower the arm it brings the hydraulics alive and allows me to operate the arm but it wont go into gear, forward or reverse. I've read somewhere that people have had these same issues but I have not found a solution to my problem yet. It did...

I am looking to replace my current 50" Toro Timecutter zero turn with something a little bit more beefier. The Toro is fine but it not able to take the hammering of my yard(3 acres). I've heard good things about pretty much all commercial mowers and my neighbors have a Bobcat and a Scag and both...