Search results

The fuel is drawn up from bottom of tank through a pickup tube coming out the top of the tank. That tube maybe damaged. First take the hose of the inlet side of the primer bulb, put thumb over end of the bulb and squeeze it checking or good bulb function. If bulb tests OK, then follow the...

Cannot say why you are not seeing a fault code but when the valve light is flashing means the main controller is detecting a fault. The number of flashings between a slight pause. A steady flash (1 blink then pause) indicates open circuit in the power output wire. Keep in mind there are 2...

When warning light comes on there should be code. DO NOT turn key off or push stop button before pushing the "hold for code" light button. There is only one brake line output from valve then tees off to front and rear brake. One axle cannot lock up hydraulically without both locking up.

Here is a clearer pic of the Bobcat, grill and screen sure look the same to me. If the Kioti screen is not exactly the same it should be close enough to make it fit.

Oliver Super 44 offset Nore: front grill is different but that could due to production year.

The reverse end of your pedal is bent downward where red circle indicates. Picture shows it being almost horizontal, it should have an upward arc. No idea how or why it bent but it is.

The fuel solenoid has 2 power circuits feeding it. One is a momentary high amperage input to pull the solenoid ON then shuts off, the second is a lower amp input that holds the magnet in place. Hearing 2 clicks when you turn the key on indicates to me that the fuel solenoid is not working in...

The attached is parts illustration for that 9TL loader. Note: item #12 bushing requires qty 8, means these are used on the front 4 bolts of each bracket. Looks like they used a bushing spacer rather than offset the plate. If these bushings are not in the kit probably best to order from Bobcat...

Here is the schematic for it. Let us know what you find.

This may be just the style of steering system used. In their previous models CK & DK series Kioti used 2 different systems. The CK 20-35 had "Load Reaction Steering". The when steering wheel was not being turned, the oil in steering cylinders was blocked at the steering orbital motor. This...

The bucket that came with the loader is 68" and grapple is 60". When using it for loose brush it will grab enough with branches hanging over the sides to make it interesting weeing where your going heading to the burn pile. Mine is a modified skidloader bucket with single grapple fork. If I...

My mistake. That one is different than some other models. That bolt holding pin in form the bottom comes out then pin comes out the bottom. Here is the R&R steps from service manual.

There is steel plunger under the magnetic solenoid. Plunger has a steel block on it that drops down into notches in the brake discs when power to solenoid is turned off. Below is part illustration for reference. It is possible brakes were not releasing properly and rather than fix the...

No disassembly of valve required. Just remove the plug cap currently in valve and install. If he has the hoses connected to correct coupler on the boom, the this plug goes in the top side of the valve as it sets in the machine. It is shown in the installation instructions for the clamp...

Jabonee is correct that there is not a port relief in that auxiliary valve section, but there a simple port relief installation for this. Below is quick photo snip taken from the Installation Instructions for a Bobcat Thumb. For this serial number order Port Relief part number 6680065 and...

The bushing tube the parts guy gave you comes with the alternator, you also need bushing part number 6817556. Here is picture of it mounted.

here is picture of the switch in the Standard suspension seat. Still mounts to bottom of the seat. Only seats I can think of that have seat switches and arm rests are some of the Zero Turn mowers. Might try a dealer for commercial lawnmowers.

I have dual function up front, QDs for the grapple and fixed plumbing to hydraulic QA levers. Mounted a manual diverter valve at the corner of lift arm. QDs for the Here is a pic

Remote (hydraulic) operated from the seat can be done, just a matter of how you set up the locking levers and cylinder or cylinders. I went the manufacture route and bought the SSQA, and all of Bobcat's current QAs are designed with ability to add the hydraulic function. The lock levers have...

Ken has been posting this on both Kioti and Bobcat forums. Below is the Bobcat schematic. I wanted him to check for proper inputs, but according his response on Bobcat forum the wire colors are not matching. It takes 12v power input from the 20a fuse (red/white wire) and secondary signal...

Use a 3 point stabilizer/stay strap set up on the 3 point draw bar currently using. It consists of an upper and lower half (2 bars per side) that fasten to the top link bracket of the tractor and over the lower pin on 3 point, then are bolted together. This will hold the 3pt arms in position...

Dropped Axle, It took me a few hours after first reading your problem to recall this. but thanks to Scott and Texasjohn's replies this dawned on me. When Bobcat first took on the Daedong (Kioti) line they encountered problem on the CT120 (CK20) with no start (engine would crank but fuel...

I had same thing happen to my HF chop saw. Not having any luck finding a switch to fit or modify slightly, I put in a push button starter switch purchased at auto parts store. Drilled hole in front of the handle to mount the switch and now I grip handle with fingers and squeeze with palm of...

Take the plug out where I drew the red arrow. If the valve has it's own relief it would be under that plug. Relief stuck open would give the symptom described if the valve is not plumbed in Open Center series. With only 2 hoses going to tractor, it may not be is series with the 3pt system.

Occasionally I have had need for a narrow bucket to reach in between trees and to load rock or mulch in the wheelbarrow to haul where tractor will not fit. I don't mind wheeling and dumping a wheelbarrow but HATE shoveling it full. Since I seldom use my pond scoop for anything other than rear...

Appreciate the comments here guys. just want to make it clear to anyone reading this, any and all deficiencies in these welds is solely due to the operator (me). The machine is so much easier to use than my old AC tombstone it's unbelievable. Mark, I went back and ground off my attempt at...

I recommend this welder to anyone that is looking for a simple to use machine that even an "hack" like me can do a half-way decent job with. Here is another project I did today. Main reason I bought the welder after my Lincoln AC 'bit the dust". Adding a QA plate to my 3pt. pond scoop so...

OK, there have been some pretty serious discussion in this forum lately so are you guys ready for some chuckles? It finally warmed up enough this weekend to lay in the shop a little bit. Not having much scrap left over from earlier projects, I didn't have much to practice on so I jumped...

I have 42" and tried 48" before buying, but found the 48" were too difficult maneuvering where I normally use them. This past weekend I was in the woods cutting up downed limbs and trees with forks on front to lift limbs off the ground and carry-all on the back to load wood on. Then I wished...

My new welder was waiting for me when I got home last night. The poor thing had to ride from California to Chicago then down to Tennessee, so after opening it up to make sure it was OK. Nice, well packed to avoid damage. Unpacked it, used the 120v adapter and plugged it in. Yep, it runs...

:thumbsup: Exactly the reason or 1 of the 3. When Bobcat first came up with the idea they were going to put flexible flag on in place of the handle then decided to leave the handle in place and drill a hole in it for the cylinder pin. 1. The handle indicates when open or closed. 2. In event of...

Fred, This might help some. As you are aware, Bobcat used the V2003T (56 HP) in some models but in same frame without Turbo they used the V2203 (46 HP). So I can't be positive of the specs on V2003 aspirated engine. Comparing specs of V2003T vs V2203 almost everything matches (injection...

There is a power and ground wire wired in already. Look at right rear corner just below the tool box shelf, there are 2 wires with round "bullet" style plug connectors for rear work lights. Wire is hot, no switch, so you need to add a switch with the lights.

It's on back side/rear of the valve. Easy access.

Here is picture of the under side of the seat plate. Looks like there is another set of holes to mount the slide rails back farther. If this is only hold up in your decision, mention it to the Salesman. He will very likely have the seat moved back so you can try it.

Is this the first time having the Box Blade hooked up? Bounce might be that MLS valve sensitivity needs adjusting for weight of attachment. It is not difficult to adjust, hardest part is getting the seat off. Here is the procedure. Make sure tractor is in neutral with brakes locked and...

I don't recall who mentioned this on TBN a few months ago about making a 3 point mount on set of QA pallet forks to use on either end of the tractor, but it got me thinking. When I buy rolled hay I have to unload the trailer at the road and haul it back to the barn (about 1/4 mile) with the...

Mounting them in a bracket not only looks neater, it gives you something to push against while trying to hold the female lock ring open while connecting or disconnecting. I ran my hoses down the left side simply because there was more room to run hoses from my rear remote and better place to...

Here is the part illustration from that page link. Prices are not listed and you cannot order direct from Bobcat. This will give you part numbers needed if dealer can't figure out what you need.

Looking at Kubota's online parts illustraion for the L48 HST, I see there are 2 pairs of poppets/reliefs. The first picture is of the "Valve Assy High" which should be the high pressure relief with directional check. Item #030 (qty 2). The next pic shows what Kubota calls "Vlave Assy. Low"...

No hydraulic brake with no or sluggish drive indicates low or no charge pressure. Possible charge pump failure, charge relief stuck, flushing valve stuck open, or hydrostatic pump worn so by-passing internally. Here are couple pages about testing charge pressure and flusing valve. If charge...

David, Here is a layout of something similar I am thinking about. I put posts in rear wall at 4' spacing for 2 reasons - 1. to better support the inner kick wall. 2. To sue as rafter support without a header system. Build front height tall enough to get the tractor under & loader to reach...

Here is a drawing of what the nylon block/pedal lock linkage looks like. There shoudl be 1 on each side of the inside frame. The lift (left) pedal hase a bar going across the the chaincase frame, just behind the steering panel, to the control valve. This bar pivots at the center of the...

How about something like this? Extend the back of the U up higher (blue line) to give something to push on the pin when driving into it. That way if one side hits first it just pushes the bucket square with the other. Taper the side plates at the front to allow better roll into the pin...

Getting just the joystick lever out is not a big problem if you can get the bottom of the boot loose. Lift it up loosen the jam nut and unscrew lever from the pivot base. This is and extra joystick I have. Plans I have for it, a straight lever might work better so if anyone wants to trade...

When I got my used forks last year I was planning on building my own frame, but due to material availabity in my area and doubting my own welding skills I just purchased a frame. Wnat I planned was something like this picture. Using 2"X3"X 1/4" wall tubing for top & bottom frame then weld...

Here is where the wires are on the "white" version. Imagine it should be the same on Kioti.

Anyone else noticed the psot count is not counting up. I check a few members that post frequently back to 11/09 and they have same post count then as today. Including my own. Just wondering if it is in the system our in my PC.

Here is an idea for you inventive guys that need cold weather start up but max tow cooling. Add a 3 way electric solenoid to line coming out of radiator going to the cooler. In normal heat/working condition it will go through radiator then through Aux cooler. For cold start up, flip a switch...

Front & rear both have a slight toe adjsutment. Attached is the procedure and spec. this is for all 5610 to date and 5600 with 4 wheel independent suspension. Not for A,B, or C series with straight axle.

Here is a little gadet that saves some time and effort pulling T posts. Took me about 15 minutes this afternoon making it from some scrap angle iron laying around. In the photos I was pulling off the Quick Hitch on 3 pt. Just back up close to post, drop the triangle over the post, lower 3...

I came across this set of forks today. New frame (fresh off the lot) and used 42" forks. Are they worth $600. They are SSQA mounted.

I have 120V 125 amp wire welder, mig capable. It says to hook up torch to negative with flux core wire and to positive for solid wire. What is the defference? Does one give hotter arc versus the other? I have always used with flux core because I am either welding outdoors or with shop door...

Herald Citizen - Man killed in bushhog accident This was in Moday's paper. Apparently the man was either fell off or was knocked off back of his tractor while bushhogging and ran over by the cutter. Officials suspect he was knocked off by a tree limb. No information regarding the tractor age...

Has anyone out there modified the boom on a Post hole digger to hook up to a 3 point quick hitch. I have all my attachments set up no to use off the QH except have to remove it for the PHD. If anyone has done it and has pics would be greatly appreciated.

First I would like to thank all who have posted ideas on garden bedders, this gave me a lot of ideas to work with. Here is what I came up with. Got a 1 row cultivator from TSC. Each spring shank has 2 hole positions, with all moved to inner spacing it fits my rear tread width very nice and...