Search results

Tractor is a 2020 CK3510HSE (hydrostatic, SE, open cab) Seems to be a lot of reference for the F6800-16411 fuel filter, including my own manual. My tractor has a clear bowl and water sensor on the bottom. Looks like EH35-0011A based on what I was able to get from a cellphone pic (side with...

Thread bump. Ck3510SE open station, 255hrs. Ran it last weekend for a bit to move some logs and no issues. Calling for snow (finally) so I went to swap the grapple for the plow. Started and warmed up, shut it down to connect hydraulics and when I started up CEL was on. I think the code was...

Pretty sure those are the same lights I used on my ROPs. Or my truck, or my camper. I have lots of nilights, for the money a very good light.

Field install cab is dealer only? Mirror kit is dealer only?

That's cool, but the OP wants to add a snowblower....

Kind of makes you wonder.... I also noted that the manual recommends re-adjusting the slip clutch if the grinder has been unused, as the "tube" may be damaged and it will not be covered under warranty. Seems like maybe too light of a PTO? Looking at what was left, seems like I had plenty of...

Bumping the thread for the same problem. Cut my tube off @ the u-joint, then tried a weld bead inside the tube to shrink it. That was a waste of time and caused some issues. Then had to slit the tube and hammer it out. How in the heck am I supposed to get the new one in? 39", I can cut it...

Where did you find them so cheap? Best I could do was around $50, but shipping was almost the same. Used stump grinder, the overlap on the tubes was "enough" until I used it on a slope and almost slid them apart. Pushed everything together and then this happened about 5 minutes later Best I...

Well this: Definitely leaks! Polished the paint off and re-assembled with 4 new 116 size Buna-n 90A o-ring.

Thanks. I cracked mine loose to break the paint and then snugged it as right as I dare, no change. Parked the tractor and ordered a pack of o-rings before the flood started. There's a few other threads about this, yours was just the first I found.

@BrkMstr This was the o-ring in red, correct? At 239 hours, I was screening topsoil today (back and forth between 2 spots) and noticed some oil. After some cleanup ended up with the seat off and my leak is a drop every 3 seconds from here, I believe this is the opposite end from what you fixed:

What's the proper antifreeze? Mine appeared green, the manual is kind of vague and with the numerous formulations these days I'd like to avoid making sludge. Overflow is almost empty.....

I need to download this on my computer, phone scrolls horrible. I'm not sure it contains the SE diagrams. The SE(not cab) seems to be the redhead step child in the lineup....

I was looking at it yesterday and the plug on the backside of the cig lighter looked a little suspect. Was able to get a long flat blade driver in there and push it back together without having to disassemble anything Power! Certainly explains why I could not find a fuse issue. The cig light...

Lights are on a custom harness, that isn't the issue. Just had them plugged into my truck and everything works fine. The cig outlet is dead for some reason.

I used a multimeter and I am pretty sure swapped fuses. Everything else works as far as I know. Digging in this afternoon.

Bumping this, it's almost fall and I'll need my lights soon.

Last fall I quickly added a 3 LED light bar (mounted to the ROPS with magnets) and wired up to a switched cord plugged into the cigarette outlet. Worked fine, was quick and non invasive while I was working on other projects. Past 2 times plowing I noticed the lights would dim about 3/4 way...

Converting a 7.5' plow to SSQA and stuck on best way to float it. Original thought was ridgid mount and use the float on the loader. Or should I make float with a chain or telescope too link?

Nope, we've tried those, they don't fit.

Yes, it is supposed to have them per the sales literature, pictures and standard equipment list. I'd be curious to see what everyone has for seats on their ckXX10SE open stations. Seems I may have a unique seat

Any have a on for the Left and Right armrests on the ck3510SE open station? Sales brochure and specs say they are standard. Tractor didn't come with them. Dealert has sent me the RH for what appears to be the base CK model, holes don't line up. Dealer now sent a LH and RH kit, same deal...

I feel like I am missing something obvious here so please tell me where I've gone wrong.... I'm in the process of installing a diverter valve and building a grapple. Kioti CK3510SE Diverter Valve, Flow is from curl/dump into valve, then A/B go onto the curl/Dump. C/D are tired to the grapple...

Working on a diverter for A Kioti CK3510SE. Initially though the loader fittings were JIS, and bought the required ($$) adapters, which function like the left image: Took a few fittings off yesterday and found that it is actually BSPP. Essentially the same threads as JIS, but the male...

Anyone know what fittings come factory going to the kl4030 loader? Specifically, I need to re-plump the curl circuit as it goes into the disconnect at the loader mount. EDIT: Hoses are 3/8, I initially guessed JIC 6 and mis-measured the major diameter of the thread at 0.600" which doesn't...

Finished detailing it out and have it setup for the laser cutting sometime in the next few weeks: 60", opens to 40" and weights ~260lbs

Since I finally pulled the trigger last month and got the tractor, figured it was time to plan some implements. Here is what I have so far, need to review my steel quotes and price this out properly (as well as finish the detailing!). -60" -~250lbs (missing cylinder, pins and some gussets)...

Any online sources for the Kioti Brand 3rd function kit online? Huge price difference from local dealers, my dealer is currently closed (covid 19) and can't really order parts for the foreseeable future.

Thank you. My paperwork is also through DLL, no serial yet. Dealer claims that is the only dropdown in the finance software. Not sure what to think. As soon as I have the serial I am going to call Kioti directly.

I've been working on getting quotes for a CK3510SE (see my price check thread) and have settled on the best deal with a dealer with a longer history selling Kioti. Dealer does all the paperwork late yesterday and send's it over....listing CK3510HB! What's the deal? Very little information on...

Tried a lot of tractors before stumbling into a Kioti Dealer and lo and behold it seems to check all the right boxes (lift cap, ergonomics, features and $). Pretty much settled on the CK3510SE as it really not much more then the base model. What a good price? I have 2 dealer quotes that seem to...

Looking at the MF 1735M compared to a few other options. What is the hydraulic flow to the implement? Spec lists 12.1gpm, but this seems high. Competition is around 8gpm implement, 4gpm power steering, 12gpm total. Is MF published data misleading or incorrect?