Search results

Nice. Thanks for sharing.

Re-surfacing this thread... I have a GC1705 and am not clear about this statement. Are you saying brakes do not engage equally in both 2wd and 4wd?

Hi All, thanks for the replies - this helps out a ton... generally sounds like local shop hoses are as good or better than OEM and replace as needed, possibly in pairs or if in a dangerous location. I wasn't sure if they all tend to go around the same time, and it's now clear that isn't the...

Seems I need to replace a hose on my GC1705's FEL (DL100)... part SL103366. The tractor/FEL is around 10 years old, and is stored outside. Should I be looking to replace all the hoses at this age, or should they generally run longer? Is there a standard replacement interval? Is there much of...

Thanks - can you describe what you'd call wadding up? Is this just a slight build up on the tines, or big clods starting to connect the tines?

I have soil that is about 60% sand, 20% clay, 20% silt. The soil is mostly dry on top, but 3-5" down damp... If I start tilling it, how will I know if is too damp? If you say something like 'it clods up', can you give an idea of the size of the clods when I should call off the tilling? Thanks!

The thought of putting a valve on there is a good one, though it would be tiny, and would need to hold up to the heat OK. Similarly, I suppose putting some sort of nipple with a section of tubing and a valve on the end of that might be an option. However, that plug is super small... like 3/8" or...

I had a similar issue with my GC1705 gauge ceasing to work after many years. Screws were not fully snug but also not loose, per se. I removed, wire brushed screw and contact, and replaced/snugged (one-by one) and it works now. Thanks for the info.

The owners manual mentions annual coolant change, and directs you to a hose, which seems to only drain the radiator. Draining the block seems to require removal of a plug on the side of a block, but it's definitely a messy process as the coolant runs down the block, axle, frame, and everything...

What's the reasoning about keeping volume to 75%? Does it maintain some cushion at 25% air?

Thanks for weighing in. They didn't freeze the first 6 years! I went out and extracted a little fluid, and by first appearance, it seems the rear tires are ballasted with antifreeze. I use the tractor to plow snow, and there are times I have to get a running start and wish I had more weight...

I have a GC1705 that I bought used about 7 years ago. It already had loaded tires. Last winter, the tires were freezing. Today, what's the preferred approach to loaded tires? Is there a thread or site I should read? If not what fluid, ratio, and volume is needed, and how to do you get it in...

Thanks - sorry, it's much older

Must be a pretty common issue due to design. Did you also get a lot of small debris around the pivot point of the axle? 525 sounds a lot more reasonable than 283 to me. Keep me posted what you find on parts or other info.

I have a GC1705, and it appears that the front axle seals have leaks on both sides. Can someone familiar with the topic confirm I am diagnosing this correctly? Looks like I need to replace the oil seals listed as #13, as per the below diagram, and that is the only part I need to buy? Anyone...

I have a GC 1705 and can't locate my owners' manual. Can someone remind me the service intervals for oil and hydraulic fluids? I'm using the Amsoil Synthetic Tractor Hydraulic Transmission Fluid (ATH) and Amsoil Synthetic Heavy Duty 10W-30/SAE30 Diesel Oil (ACD). I'm not sure if that changes...

Hello, Have a GC1705, and after some hydraulic leakage, slightly overfilled the hydraulic reservoir so the sight glass is entirely full. I think it's overfilled by half a quart or less. Based on other posts, it seems like if it overfilled, it's more of a risk of it blowing out the top than...

Has anyone had success in adding a chute blocker and mulching blades to the 60" MMM? I saw some older threads about people not being able to locate any gator blades, but didn't see anything recent.

Time for a little leaf planning. I'm on an acre, with about 1/4 of it getting pretty heavily covered by 6-12" of leaves (3 mature maples). Most of the rest of the lot is pines/spruce and some larger honey locust. About 35 mature trees, in total. Last year was the first year here, and using the...

I have a GC 1705 with the heavy hitch. I also have a small 2-wheel utility trailer that I'd like to be able to pull behind it as a hay ride at a birthday party. I know there are risks with pulling a trailer like this -specifically that the hitch can raise up. What are the ways I can stabilize...

I'm looking to build my own ~5 gallon cart sprayer (12v) to use in both a large vegetable garden as well as for fruit trees up to 18' or 20'. Does anyone have direct experience as to if a single sprayer with different nozzles can work for both of these situations? Anyone know what a good...

I'm putting in a new garden, and there are a few deer in the area, as well as tons of rabbits. I have some 2' tall 1" square welded wire, I thought I would use on the lower section for the rabbits. I was thinking I would use some T-posts and electric wire or string to cover the upper part. How...

Thanks for all the replies. This ground turns rock hard when dry, and definitely needs some moisture-holding content added. At some point when the soil is holding moisture and has a lot of works, I hope I won't have to till regularly, but we will see. I've heard several times I need a small...

Thanks for all the great responses! I didn't realize there was a Lawn and Garden forum, so thanks for letting me know. I've gardened for a number of years, so the timing question is less about planting, and more about timing for working the soil. There are a ton of weeds growing in the grass...

I received my compact tiller last week, and am ready to get going with the garden prep -- however, need some advice on tilling and amending the first time! My soil is 60% Sand, 20% Clay, 20% Silt. It's rock hard when it's dry. Surprisingly, I haven't found many rocks in this soil, since I moved...

Here's a photo of the fitting. It is actually the lower fitting that is leaking, though they are the same. Regarding the comment about threads being worn each time you tighten them (and the second time I cranked on this pretty good), one pair of the hoses that came with one of the cylinders...

I received my King Kutter XB tiller last week, and just finished setting it up. Looking forward to using it! As I went through and checked the gear boxes for lube level, when I removed the check plug for the side gear box some light fluid, watery consistency, came out first, then the OO grease...

I received my 60" Massey Ferguson snow plow after 3 months, just in time for the end of winter! Unfortunately, it only came as parts, requiring full assembly. Is this the norm? Also, does anyone with the snow plow, snow blower, or broom have issues with it not being level when in the straight...

I purchased a Massey Ferguson 60" snow plow blade for my GC1705. Unfortunately, it came only as parts and required full assembly (a bit surprised, actually) After getting it all together and mounted on the tractor, I learned that one end of the snow plow is about 1.5" higher than the other end...

Bought and assembled a new snow plow, and have a fitting at the raise/lower hydraulic cylinder that leaks at the 3/8" fitting. I used permatex thread sealant with PTFE (as per Massey Ferguson instructions), and even after disassembling and re-assembling with fresh thread sealant, it continues to...

Are there any weights that attach to the bar extending from the front of the frame (just below the 'brush guard'). I see an Agco part 79023233 for the front weight setup, and assume this is different. In any case, which weights will fit, outside of the Massey specific weights?

I have a Massey GC1705 that I added Pat's Easy Change Hitch this week, because I have a tiller on the way and want to simplify hooking it up and detaching it. I installed the PECH's when the 3-point lift arms were about level - near the bottom of the range of motion. When I raise the hitch all...

On my tractor, I have one adjustable link that attaches to the right lower arm. I think this is called the side link, or the lift arm leveler. Do I understand correctly that this is primarily used for tilting an attachment to the left or right? With a small tractor, I'm also thinking about how...

From the looks of it, the Rankin ER 25, North Star 100 series, Northern Tool NorTrac, AgriSupply 73410, and Gearmore subsoilers are all the same design, if not made by the same manufacturer. Does anyone know if they are the same, or if any one has features or is better built than the others...

I'm looking at various subsoilers, and their length. Ideally, I'd get something that can go as deep as possible, in the event I want to pull some pipe. That said, I know the GC will have its limits. How deep can your GC run a subsoiler, in various conditions/soils (and what are you using)? I...

Is anyone using Pat's Hitch with a tiller on your GC series? I've heard that there is some play in the attachments, when mounted to Pat's, and that some implements such as tillers may not be as good on a quick hitch. Also, have heard that the extra 4" on a SCUT can be problematic, but haven't...

It's been a busy week, and I have little free time in my schedule, so it's not like I get to follow things real time. I'm just catching up now -- nice lively thread. Can a forum moderator explain why my original thread was closed? I didn't see anything that warranted that. Common to have to...

Would you expect new attachments to be received with paint damage, in some areas down to the bare metal? Perhaps I'm just being picky, but thinking I should not have to go and find matching paint, then do touch-ups on a new pine needle rake from Everything Attachments to prevent it from rusting.

Looking to buy a King Kutter TG-48 Tiller. Does anyone know of an online retailer with good prices on product and shipping? Shipping to Denver, CO.

I'm new to using a tractor with a 3 point hitch and have a few questions, as it pertains to the GC's (have a GC1705). 1. if I go across a water ditch will the hitch allow the implement (a pine needle rake, in this case) raise up as I go up the ditch? 2. Is it safe to hold the hitch raise/lower...

I have a GC1705 and went to drain my coolant today, while installing a block heater. Since I bought the tractor used this summer, and it is a few years old, I figured I would fully drain and flush the system. The drain pipe seems to really only drain the radiator, and not much of the rest of...

Finally ordering a 2340 blade for the winter season, and curious if the Rubber Cutting Edge works well for snow/ice and if it's worth it ($250)? I know a lot of these wear edges aren't rubber, per se, but poly, etc. If it matters, my drive has contours in some areas where it rises a few inches...

Getting ready to perform my first service on my GC1705, and could use some clarification on a few of the hydraulic oil change procedures: 4.4.3-14: Clean the transmission suction filter screen in solvent or kerosene. Q1: I don't have any kerosene or solvent around, and don't really want to keep...

Looking for a 2340 Front Blade for my GC1705. Are there any 4-way hydraulic front-mount alternatives to the 2340 that are cost worthy? If anyone knows of a used 2340 (or a 2360 blower) for sale or a dealer with competitive prices, please shout out. My local dealer was talking about $3000 for...

Have a GC1705 and am performing the 50 hour service... I'm switching over to the AMSOIL ATH from the factory fluid. When changing the hydraulic fluid, or when switching from the Permatran to ATH or another synthetic, does anyone attempt to drain the hydraulic fluid from the FEL hydraulics, or...

Massey has some recommendations for engine oil weight that are (naturally) temperature dependent. Living in Colorado, we could see 90's in the summer with 50's in the evening and freezing in the late spring and early fall when day temps could be in the 80's. Winters could be blast below 0 or in...

WTB Massey 2340 Blade or 2360 Snow Blower Let me know if you have one at a good price.

Hello, I am plowing an area for the first time, in high clay content soil. I haven't plowed previously, so this is a new experience for me. I have a Massey GC1705 and an Everything Attachments single bottom plow... though I'm not sure what size it is (awful **** heavy!). What depth is ideal...

I just parked my GC1705 and it is overheating... boiling coolant in the overflow tank. I also see the filter in front of the radiator is jammed up, and cleared it. What should I do? Let it sit, or start it up after clearing the screen?

I just parked my GC1705 and it is overheating... boiling water in the overflow tank. I also see the filter in front of the radiator is jammed up, and cleared it. What should I do? Let it sit, or start it up after clearing the screen?

Anyone own the MF 2335 or 2340 snow blade/plow? If you own these guys, do either of them tilt to the left or right, without the hydraulic kit? It wasn't clear if the hydraulic kit tilted side to side, or the top and bottom in and out.... I'm guessing the former. Info on the MF site is pretty...

With crazy hot weather currently, it seems like the wrong topic -- but we're only 6-10 weeks off from the early snow season. Recently purchased my GC1705, and am contemplating snow removal options. I've surfed a lot of threads, but am looking for some insight as to what is best for my...

Hello, I'm looking for a tiller for my MF GC1705. I am curious how meaningful are the advertised tilling depths? For instance, the following tilling depths are advertised: KK XB 50": 6.5" KK (non-XB) 48": 8" Land Pride RTR0550 50": 5" Seems like a pretty broad range, and that deeper would be...

Have a GC1705 and am curious what tillers people are using on their GC 17xx's, and how they are working out for you? Do you have a sub-compact version or run a standard compact version of a tiller? I am seeing a variety of various tillers with different tilling depths. For instance, the KK XB...

> Pictures, or it didn't happen! haha -- ok, here's the 'evidence'. Not the best pic, but the only one I have at this point!

Hello, I recently purchased a used MF GC 1705 with a 3 point hitch. I have the tractor and loader manuals, but not the hitch manual, and I don't think it's available from MF online. Does anyone have a copy of the manufacturer's manual you can share that explains the proper adjustment of the...

I have a MF GC1705 that I recently purchased, and am looking to buy a used tiller. I located a King Kutter XB, in good shape I am considering, and the owner removed about 1" off the original PTO shaft. Using the video by (Temporarily blocked due to reports of company closure) at: How to Measure and Cut a Tractor PTO Shaft -...

I'm planning to purchase a used Massey Ferguson GC1705 (SCUT), and would like to know my options for adding a small subframe mounted backhoe. I've spoken with Woods, who in planning but has not yet manufactured a subframe, and Wallenstein. Building my own subframe could be a third option. I...

Hi, Second post here on tractorbynet - what a great site! I'm considering buying a used 2013 GC1705 with 70 hours. It has the 60" mowing deck, DL100 FEL, and Joystick. We purchased a 1 acre property, and have a number of gardening, landscaping, and other projects. Additionally, we have about...

Hi, First post here on tractorbynet. What a great site! We're looking to purchase a sub-compact tractor. We have just an acre of land, but a number of gardening and landscaping projects and 200' drive and large parking area that need snow removal and between these needs, that would make a...