Search results

Lifting you and family in prayer during this difficult time. God Bless .

We took 5/16” fuel line and put one end in can of fresh diesel (by passing tank) the other end we connected to inlet on lift pump. Tractor started but then acted like it run out of gas and died, this isolated the problem from fuel tank to electrical. Probably where fuel solenoid wire was cut out...

2007 Branson 2910i :Engine Kukje : A1400N3-D :3 Cylinder: SERIAL # CN8N00043 Old version tank : Left side part# NTE10100000A0: Right says see comments(this is one I need): There is new version list part #: NTE10200000C0. (RH). The old version is no longer manufactured .

After checking fuel ,I agree it is not fuel, it is electrical, the wire to fuel shut off solenoid was burnt,we cut wire out and replaced with regular wire. After reading repair manual , looks like we cut out the dionde, we kept piece it is thicker, so it would seem it is wiring to fuel shut off...

Have replaced fuel shut off solenoid twice, after removing the what showed to be a bad one,what a challenge, after my brother showed me what to remove and buying thin flat wrenches, replaced it again. I want to know is wire going to solenoid a resistor wire? and where would I buy wire that...

I will update status of tractor. Took hose off lift pump connecte we by-passed fuel tank connected a 5/16” fuel hose to fuel lift pump with other end in clean 1gal diesel can, tractor started strong , then about 3 mins. just died. We tried starting but this time tractor wouldn’t make a sound...

There is a fellow on Facebook TYB/BRANSON couldn’t get head for Kukje engine, he ordered from dealer and dealer sent money back stated that South Korea could not ship to US. He said bare head was to be over 3000, anyone shed a little light on this? I personally am of opinion I may not be...

Thank you for this, I used suggestion. I also pumped all diesel out of tank.our landfill has oil, filter, fuel recovery, I have 55gal sealed plastic barrel I use for this.

Ok brother came over Saturday, I had already looked under tractor at fuel tanks , impossible to check fuel lines without dropping support frame,unless I can find a tank I will not attempt this. Here is what we did 1. disconnected fuel line from tank to lift pump added 5/16 fuel line ( new hose)...

Maybe that’s what has happened, the engineer died.lol, sorry but I need to laugh helps me not to cuss problem, that I probably created.

I hope injectors are ok. I will look in manuals find where safety switch is located. Thank you your help is appreciated.

Took stopper out and started tractor again it ran several minutes then died suddenly. I plan to get under tractor and replace fuel lines and check connections for clogging. After that if that doesn’t work, I guess have injectors checked. Is there a possibility of using another fuel tank maybe...

I have used rubber stopper at lest 4years but it didn’t fit properly so maybe it wasn’t sealed, I started in August having problems, I changed fuel filter , and it would be ok then in September, while pulling up t-post that were on incline tractor suddenly died, I assumed it needed fuel, but...

It doesn’t vent from tank? So I replaced old rubber stopper with new one, so I tank would need replacing.

I put a rubber stopper in tank opening, it has been several years, I suspect that is probably big part of problem trash in fuel tank , is there a fuel pick pump in tank? I believe the tank needs replacing,

Yes after it sits, I have been looking for fuel tank for it, the plastic filler neck broke off several years ago, the tractor is 2007. I put in part number, but get no results, I am wondering about fuel sensor in tank could be clogged? Anyway I think dropping tank and replacing fuel lines . I...

Thank you for answering,I started tractor today(Saturday) I timed it 2minutes then died suddenly, before it ran about 1 hr. then died suddenly. I turned key on and took fuel line off going to outlet side of fuel filter and diesel came out . Will try your tip of connecting fuel source to pump...

Tractor shows all fuses good, fuel shutoff solenoid getting 12.2 v, new fuel filter, air filter, will idle and drive about 100 ft then die, I am wondering if fuel pump or injectors are bad?

Could be it dropped a bearing in shifter.

Look at Cub Cadet 7193 the two use same parts. They are both same engine ring set 0.75 os part MA-MM431633

45fmj I will reply in Satoh forum

I don't know amps but it is 12 volts

I buy 10 gals. my tractor will use most of the 10 gals.

My Branson 2910i takes 9 gallons.

Good morning from West Texas,42 degrees and drizzling rain, high 58, after last week’s weather , I’ll take this. I am starting vegetable seeds in house . Have a great week everyone.

I own Branson/Tym 2910i and before this tractor a Kioti 35horse and a BeaverIii comparable to your Cub Cadet, I bought Kioti new , the dealer is wonderful, the tractor is a little light on the back end, I sold Kioti broke even and bought the Branson I found in a field some 2 yrs. before I bought...

Good price , but from past experience the tractor was kept outside, and sit awhile, I have equal to yours mine is 2910i Branson, and it sit outside in a field at lest 2 years, if you replace head, I knew I would need to because my brother is retired diesel mechanic, he told me there would be...

I know this is old post, but in July 2016 the head cracked on my 2007 Branson 2910i , it is very same as your Century, I called several places, I am in West Texas, and found one at Anderson Tractor Sales 115 CR 305, Carthage,Tx. 75633;Phone 903-693-6628. I received:3 -spacers for fuel injectors-...

I look to AgriSupply for parts replacement for my old equipment, you might give them a try. I also have a 1960s disc harrow by John Deere with wooden bearings, I use AgriSupply to replace parts the bearings are replaced by steel bearings

I downloaded manual from Messicks The pictures are from my Bushhog TM-5 it needs total rebuild

Looks like my Bushhog TM-5 Serial # 1103003 it is obsolete. It looks like I can buy complete spindles for about 52 a piece.

Here are pictures of location of fuel shut off solenoid. It is directly under adjustment valve, you will need to remove adjustment valve before you can remove fuel shut off solenoid valve.this is same as yours,mine is 2910i. Maybe this helps

Just an idea remove fuel filter assembly then remove the do not remove part (that's the adjuster but it can be removed with wrench) you should now be able to get thin wrench on fuel shut-off solenoid, another little advice do you see connecting to throttle DO NOT REMOVE, i made that mistake...

Me 20v Dewalt no complaints

Very nice! Thanks for sharing.

I would like a skid steer, I’m of opinion it would be very helpful, it has all attachments.

Oh I have loader with The Thumb by Green’s Machine, I. have moved a lot with this set up, it will pickup a single pice of tin. I am in process of making a landscape rake, I need a piece of 2” square tubing about 6’ long,to finish assembling .loading some pictures. I used 3”x4” and pretty thick...

I am looking at putting this on trailer so that stabilizers are lowered to ground and attach trencher to trailer , and attached to tractor to stabilize trailer. All ideas welcome.

More pictures of Davis 100a trencher/backhoe

I have a Davis 100A but it is too heavy for my 2910i Branson , and for several years I read forums, etc. to come up with plans to set it on a trailer like a car hauler, the little backhoe only digs about 6’ to 8’ but it beats digging by hand when you’re 72 years old. backhoe has its own pump to...

Yes i have Branson 2910i and 5’ Branson branded on side, mine is not Titan, it is Kiodiak(sp) , I tractor has 5’ loader , so I figured I shouldn’t go beyond 5’ for attachments. I really like 5’ Bush Hog finish rotary shredder. And you stated it just right. I have a 7’ blade KingKutter, the...

It happened again and unfortunately I didn’t check fuse first, and it was fuse, but I needed to replace old brittle wire, I have a good solenoid.this is easier to remove 1/4” nut , I set up two mirrors so I could see nut ,now in progress of removing nut and wire, hope this works.

The first time I had solenoid problems, the tractor had sat while I replaced hyd.pump that operated equipment, the pump in front was good and like you tractor was in the field. The fuel solenoid price was too much. I found right size wrench ground and shaped it to make a thin wall so it would...

That is part number MA-MM409334 . www.partstree.com price $82.99 + tax and shipping. www.ereplacementparts ($81.44+tax and shipping).www.messick's.com ($69.05 + tax and shipping) If you are not opposed to using used parts check on Ebay. good luck.

My tractor did that and my brother I thinks it dropped a pin. Tractor was stolen, and brought back to my brother’s shop. He will work on tractor this winter.

I ordered the parts book and repair book when we bought the tractor. They were not cheap, I think our tractor are the same, mine has manual 4wheel drive and high gear this tractor must travel at 15 + mph' these little tractors are work horses.

I googled cub cadet 7194 then checked out the search results came upon www.tractor data.com and found everything matched my beaveriii-Satoh . I then googled for parts diagram, next I went on www.partstree.com phone 512-288-4355 (they have best parts diagrams) Compared their parts numbers with...

I found parts for mine was out of sight, i discovered Cub Cadet 7193, 1996-1997 700 series compact utility tractor Mitsubishi built parts interchange with my Mitsubishi/BeaverIII Satoh, the parts are reasonably priced.

I had to replace same pump on my 2910i and you are right it is a chore to remove and reinstall, I did this 3 times, i took a come-along and pry bar to move things so I could have enough room to do job without bending other parts. After searching I found a place called Sid's Trading Co. LLC, 2293...

Yes PTO is 6 spline 1”-3/8” on tractor but I have run into some pto from equipment being 8 spline and 21 spline. Took them to machine shop had them rounded and hole drilled for shear bolt.

I expected the head to crack on my Branson because it sit not running in a field. I have the good luck to have a brother who is diesel man He got it started and I drove it around 2 years before head cracked, brother told me to order heads, thermostat, radiator, gaskets, new belts , water pump...

I contacted a huge (was) dealer of Branson looking for parts for my 2910i Branson and was told they no longer carry Branson that most dealers have stopped carrying Branson, this was Dec. 2022, so now what? Where are parts for Branson.

This is the most helpful, thank you

I found that my Beaver III 3cyl 4 wh drive is same as 7194 Cub Cadet, parts are easier to find. Just a suggestion, and both have same K3E Engine. Look on e-repair for parts diagram. I have 2 books on mine, repair , and parts, be glad to share if they can help, they were 100 each, but you need...

Oil filters for my 1988 ford f150, 2003 Chevy S10 and tractors 1978 Beaver III and Branson 2910i only Wix oil filters.hydraulic filters especially on the Branson I use those from Branson.

That was a ride! This is river bottom land , which means clay, it was too wet to use loader, it kept sliding, I was try to dig up bear grass . the back of tractor went both tires up in air, I got off tractor, and realized I just needed to lower bucket. I did and used bucket to help me drive out...

I installed “the thumb “ from Greens machine shop, sure do like them , age and health issues helped me make the decision. But I would still like to have grapple. There is Branson BL10A loader it is euro global, I have checked and instead of trying to replace all the parts on bucket, I will...

I looked up where I bought head for my Branson 2910i , I remember calling several places before I found Anderson Tractor Sales phone 903-693-6628 address 115 CR Hwy.59 N. Carthage,Texas 75633 www.Anderson tractor.net . This was in 2016 . I also have used with success Sid’s Trading Company LLC...

Wow what fun! I would love to have your skills. I have for about 5 years now trying to come up with a way to put my Davis 100a trencher on a trailer , it is too heavy for my 2919i Branson . It has hydraulic pump that runs off tractor pto. I will go today and try to take some pictures so you can...

I would move the girls out. The cheapest best I ever found is Sevin Dust, use 10%, use it inside and out, animals will pick the sevin dust up in their paws , that is also the way they pick up fleas and ticks. The best thing I ever used to bathe animals was lice shampoo for humans. Try this , but...

I agree the 25 hp is not big enough to handle that big of rototiller. I used a 5’ on my 30 hp, does ok after I subsoil first, I have a 48” that is perfect, but several years ago the gearbox went out, a guy messed up box so can’t replace gears need whole gear box, I found one that that cost about...

I need to rebuild bucket attachment for Branson BL10A parts book says it is Kukje loader, I have parts numbers, I need to know where to purchase, I called 3Rivers Implements and the recording said they couldn’t help me. Any Ideas? Thank You

Great picture, I agree with you.

People often ask on my face book what to use when their animals or vehicles get sprayed by skunks or they hit one with vehicle, I got this from a ranch family. 1 quart hydrogen peroxide, 1/4 cup baking soda, 1 teaspoon no-tears baby shampoo (I use this do it doesn’t hurt animals eyes) , mix...

Bleach if you have it, and also meat tenderizer, I find bleach the most effective if you can use it within about 30 minutes. I also keep a gallon of bleach in my vehicle in winter, poor some on tires when having to back up or start driving.

Thanks for sharing your knowledge, I always learn something on this forums .

I have been lucky so far, I have open cab. But I carry insecticide and this year I started carrying bee hat when mowing.

Thank you for the information, I bought or downloaded the manuals. The tractor had sit a couple of years in my neighbors field, she finally sold it to me it also has front end loader,5’ shredder, and 7’ blade ( it is way to big for tractor). Had to rebuild shredder, it had blades that were...

That is a good idea, I will get my brother to check , I don’t know why I didn’t think of that, just seems everything I own has broken down at same time, my DR Trimmer, craftsman riding mower, my 1988 Ford F-150, even my spot sprayer pump. And thankfully we’ve gotten almost 3” of rain, weeds are...

I am useless when it comes to electronics. Hopefully the folks at cluster fix can help. Thanks everyone as usual y’all came through for me.

Have contacted company, to early they are closed, but will answer me with email.

Thank you I will .

The only thing that works is the pto rpms and the hour meter and the needle on the rpms is broken, it looks to me a previous owner had attempted to repair. I didn’t buy tractor from a dealer.

The cost of digital board was over $500 dollars.

Where would I buy a board? Only one I found for Branson was over $5 the fuel gauge,temperature gauge, turn signals, dash lights do not work,

Where would I buy a board? Only one I found for Branson was over $500

I wouldn’t know where to get repaired.

I was wondering if there is a cluster meter board that doesn’t cost over $500 dollars to buy, a universal one? I believe the board on mine is digital. Thanks You, any advice is welcome. Sally

Hope these pictures can explain what I did to tiller

I actually went to Tractor Supply and bought bolts labeled shear bolts, goes to show you I don’t know my bolts. Lol

I had pto to tiller modified from 8 spline pto shaft to a rounded shaft on tiller with hole drilled in tiller shaft to use #8 shear bolt, now the pto shaft to tiller is round and accepts 8 shear bolt

I have bushhog and have used both shear bolts and slip clutch, I use #8 shear bolts on all my pto equipment. I bought a rototiller from north tool several years ago, input to tractor is 6 spline 1-3/8 to tiller 8 spline with slip clutch, I hit a rock broke the pto shaft inside tractor, it al...

I agree totally, I would’ve tried to buy kubota 50 hp, 4w/d with loader , backhoe, cab , and grapple bucket, I to have 5 acres, it has been in family since 1929. I found a Branson 30 hp no 4w/d. With a loader, blade, and shredder, from private seller .so if possible go bigger you won’t be sorry.

I have decided that for me a hydraulic dump trailer would be my best buy, I am looking for 5'x8', it can haul my equipment,and all my debris, from tearing some old buildings, I paid 2500 for 40 yard dumpster one load, so I still need a couple more. I am of opinion dump trailer is worth cost.

My cat went out on my pu so I cut it opened cleaned it out welded it back together, the thieves would get a surprise,we have had quiet a few stole even on school vehicles.Oh cat not required for inspection here.

My little Texas county is seeing an increase in thief, I am so frustrated some low life stole my 1978 Beaver III ,4/wd/3 cylinder,diesel. It wasn't running at the time and front tire was unfixable , have many more projects going on, tractor ran, but it wouldn't shift, I took shifter apart ,have...

You are right about thief it is high in small town I live , I had my Beaver III stolen this last Wednesday night, it was broke down, they used a trailer and winch and took it. Here where I live in town several years ago someone backed their pickup up to my carport and stole my air compressor...

For me and my needs it is thumb on bucket, disk harrow,middle buster,3point tiller,blade,landscape rake,rise bed attachment and shredder

I have always made my tractor and equipment available to neighbors except one and this neighbor is exactly like yours, I wouldn’t even let this neighbor “hire” me or equipment, no go get your tiller. I have Branson small 30 hr and would never even think about putting a 6’ piece of equipment...

I have same kind of land red clay river bottom, I found that harrow disc then Toto till, and if you have access to water , water first. The land is like a brick without watering first. It would be very time consuming to use Tito tiller.

My brother bought 2 60v oregon battery saws 16 ", he has repair shop, works on mowers,chain saws, 4x4, . Those chain saws sold fast, this was about 2 years ago, still no complaints for buyers.

Dewalt 20v 12inch , I love it, can't pull anymore due to shoulders, I have 2 Stilh 16" nearly new, thinking I will sell them and put money on bigger chain cordless chain saw.

I noticed this last year attachments doubled. I started looking for euro global grapple bucket about 2 yrs ago , they were running around 850 for 5’ , but then this year I really need one and a euro global if you find one is between 2000 and 3000. Looks like I’m going to have to add adapter and...

There is a place in Dallas Texas that rebuilds ECU , I don’t remember the name , but I probably can find out, I have a 1988 f150 ford, one the first with ECU and it went out and my brother knew about company that rebuilds ECU, I remember we couldn’t find new one, I believe it cost me $100 and...

Do you know anyone who builds computers? If so have them look at ECU and see if they can identify problem.

How about seeing if it can be rebuilt?

I replaced my Dewalt 18 v with the new lighter 20 volt lithium wouldn’t go back. My son bought me a 1/2” Dewalt 20 volt 4ha impact wrench and I have put air impact and compressor away, I love not dragging air hose around.Now he bought me 12” Dewalt chain saw, love it perfect for me.my Brother...

Well machinery will fail, something is wrong and while it’s under warranty, I would say now is time.

I want to thank everyone on this forum that has helped me keep my Brandon 2910i going.

My Branson sat out in field about 4 yrs before I bought it, got shredder and blade with it,I knew I would probably need to replace some major parts, tractor was parked where it stopped and wouldn’t start for owner. I am fortunate my brother is a diesel man and got tractor started, I changed oil...

Happened on my 2910i had to order new radiator and fan, this in 2017, radiators cannot be repaired. Put them on myself.

I would have dealer check the cylinders, my 2910i does not do that now, I knew when I bought tractor the bucket would drop and that is not what loader should do, I had all cylinders rebuilt at machine shop, doesn’t happen anymore, the bucket will stay where I put it. It is not normal for bucket...

After I replaced gear pump and hoses, gaskets exterior. Hydraulics still wouldn’t work, went back to basics,started with hydraulic filters , including the mesh one, replaced low side sucking hose and clamps, and then tried 3 point and loader, it worked, the low side sucking hose was bad allowing...

With the help of this forum I replaced my hydraulic pump for loader .The power steering was fine. I ordered all my parts from SIDS Trading Co.,LLC 2293 Hwy 25 South, Luka, Mississippi 38852 phone 662-424-0025. My pump was burnt no good. When I replaced it, the bolts that secure high pressure...

Same here HP can kiss it. I too use Brother, my favorite was the old EXmark, filled my own cartridges and it printed great.

From what I remember JD started this several years back, you were not allowed to buy parts and repair JD equipment yourself. My opinion they are monopolizing and taking away my rights as owner. I don’t buy JD products for this reason. Also DR products I bought a trimmer at garage tried to order...

Yes finish mower , worked for me unfortunately it broke and can’t find parts, so back to using shredder, it does the job but finish mower looks cleaner cut.

Yes or a thumb

I also added Green’s Machine Thumb, the third function I bought and installed myself. I had grill guard already, I would like to have grapple , but budget isn’t there, the Greens Machine Thumb has been a great add on piece of equipment.

Get the cab. Here in West Texas, I have had 2 friends stung by bees while running their tractors to shred, it almost took their lives, cab worth extra cost.

I have used my HF Drill Press for just metal drilling for over 5 yrs. I have no complaints, and frankly thought it would only last for the one project I was doing at the time, their 14” metal chop saw didn’t last the project, have bought another HF and so far it does what it should.

Sorry pictures didn’t load first time.

My 2910i Branson back wheels in air .I was scooping mud , kept sliding and overloaded bucket. I should have used 4 wheel. I don’t use 4 wheel very much, hard River bottom land. You will find this forum very helpful. Oh, I agree with Jeff.

I bought the lowest priced 3point I could find ,I garden about 1 acre to 2 acres, Northern Tool had one Direct Drive $900 now there was a problem with direct drive ,kept tearing up pto drive, theirs is 8 spline to tractor side is 6 spline, I even broke pto shaft inside tractor, could not afford...

I never had use of tractor or loader, I dug all water lines on property using a front-tine roto tiller-river bottom land is like a brick. I would water ground run roto tiller, dig and clear trench and do it again until I went 2ft. I was much younger, now am 69 yrs old and love my front end...

Moderna also didn't even know had first shot, second shot arm sore for a couple days.

This is raised bed holler I had built, unfortunately the welding machine shop sold and the new owners will not do small things. Again found Ferguson frame this time the people give it to you if you haul it and some trash they had, I did so. I think Ipaid machine shop $150 to build.

I haven’t attached axles or wheels or even bed , I also found this trailer frame in a field , bought it, I figured $50 for frame wasn’t a bad deal, the axle was way too small but frame is a good size, I think it must have come from a travel trailer.

This is trencher Davis 100a I saw it in a field and bought it, it does function, someone tried to make it 3 point , but this trencher is much to heavy for my 2910i Branson. So I am thinking of making it pull able. It operates with PTO pump attached to PTO on tractor. I am next putting up...

The Davis is old and heavy , I have run it to see if it was operational. The bucket has a hole that think maybe can repair with piece of metal. If I can put some pictures up maybe someone can provide ideas on how to go forward with this project. Thanking in advance.

I use my blade ,loader with thumb and homemade debris bar, a backhoe for tractor with thumb for backhoe would be something I would find quite useful. I garden so I have tiller, middle buster, and 3 point raised bed I had made from an old Massey cultivater. 3 point shedder I rebuilt, but shedder...

I also went with Agrisupply 2 holes.

Seems I see cliche around here in west Texas.

In a month common 2x4(actually 92-5/8) stud went from 1.97 to 7 a stud. 4x8 x7/16 was 15 now 54. Not kidding lumber prices I’ve no seen and I am 69 years old.

I bought my one and only new tractor over the phone site unseen, never went to dealers just used phone for top three to me. The first two treated me as if I was lying trash, 3rd one treated me as someone who was good for word, I bought tractor that day, gave them cashier’s check when tractor was...

Totally agree with you Tinhack

Need to know who manufactures pump for Branson 2910i 3 cylinder diesel, I have Branson part number, but I am going to take pump to pump shop and see if they can undo my mess up . I don稚 know how to upload a pictures. Thank you

I have Branson痴 part number for injection fuel pump, that doesn稚 give me OEM manufacture. I have Branson 3 cylinder diesel 2910i. I took nut off top now Pump shop needs to know make of pump.

I know it was a learning experience to find hydraulic strainer, first you have to remove the big filter you can see and then remove the cover that is behind the big filter and inside you will pull out a cylinder made of steel mesh, wash and clean it, mine had never been cleaned it was clogged...

Well I am asking for help again, as you may remember I have a Branson 2910i tractor with loader, in August 2019 I replaced hydraulic gear pump, had eye problems they are better , now Friday the 28th I was tilling so I can plant potatoes,and loader dropped, hydraulic oil spewed on tractor and me...

I was operating my Branson 2910i with BL10A Loader with Thumb Attachment by Green's Machine Company, and hit metal pole with concrete at end, the bucket will not curl. I need to know spects. of the bucket cylinder so I can either repair or replace. Thank you,

This is picture of another diverter I bought but have never used.. I don't know brand, I think I bought it from Surplus Center, it is same spects. as the X-tra. I still don't have rebuilt control valve on tractor, because it needs pressure valve set, the machine shop's pressure test equipment...

These are Diverter I think . It is X-TRA Valve Kit MP020 by Precision Manufacturing Co. I bought it with thumb from Green's Machine Shop, online, as you see I have taken Diverter off.

Sorry behind in posting, eye doesn't seem to want to heal,so please forgive mistakes.

Thank you , Yes it has 7 hoses , 4 for loader, one on left side to power beyond(hyd. pump) 2 on right side, one almost beside the 4 for the loader is going to back of tractor located above the two separate hoses that are going to a pump under right side of tractor (other side of hyd. power...

There are 2 hydraulic hoses going from back (they are side by side) they lead to a pump , it is shown in video. I would like to know their function. I have service manual for chassis and service manual for engine,neither show these hoses. On top above theses 2 hoses by the 3 point left arms...

I sheared the PTO shaft on my Branson 2910i tractor, I have part and book, but I need to know do i need to remove top plate on transmission case to complete repair, book doesn't say. I can't get PTO clutch pack back in due to shaft shuttle fork ,I was hoping. not to need to take apart any more...

Good Morning, I was using rototiller heard a huge cracking sound,shut down operation,their was pto shaft to tiller thrown to fence and pto shaft inside tractor was shredded off inside tractor. I have another for tiller, but now I need to replace pto inside tractor pto, I have a book,but I need...

Hi , I purchased a Branson 2910i with loader,the bucket shows to be a Quick Connect, it has a lever that you pull up and it should then release 2 pins and then bucket should be able to remove, now comes the problem the lever will not move, I have sprayed solvents but no luck,the lever will not...

438403 I can use valve from joy stick for loader? My loader is self leveling so i need to use up/dn ? I am not tect on computers I had a time trying to load the diagram that came with valve. If I can up load pictures of joy stick valve do you think you can tell me where to plumb valve? Thanks...

Hi I would like input as to cost for adding a model KB2475 backhoe to my new DS3510 tractor, dealer I bought from quoted $8599,I would really like input on this quote seems a little high to me, I was thinking should be no more than $6000 Thanks Sbrown