Search results

Sorry, can't help you with your problem. I did want to mention that if you have any interest in the full electrical schematics for the RX6020/6620/7320/7620 series, then PM me. They are 2 paper sheets 18"x36". I posted previously asking if anyone owned one and got no response. Toukow

Sorry for my confusion.....

From time to time, my tractor has been having issues of reaching rated PTO RPM, which I’ll post about separately. While looking into this, I found errors in the Kioti CK2610/3510/4010 owner’s manual. My owner’s manual is dated JUL 2018, so perhaps this has been corrected in later versions. My...

I’ve never seen anyone post on making the connection you reference to the instrument panel brake light symbol. Someone did post where they had installed a limit switch for the parking brake lever, which seems like the correct way to go. I was going to go down the limit switch path, but then...

Anybody own one of these tractors on the forum? Thanks, Toukow

Probably not related, buy I had tachometer totally weird out on mine with around 120 hours. I did not look at any other dashboard indications during this event. It was running and I looked at tach as I was running a brush hog, and it was pegged off the numbers on the high side of 4000 RPM. I...

I wrote a question about this too for my CK2610. I had read elsewhere that your approach is correct- don't screw in threaded dipsticks, press in the ones with O-ring type seals. So I filled to the mark without screwing it in. I was glad I followed another poster's advice which was to check the...

Did the manual come with a separate envelope that contained complete wiring schematics? I am simply trying to verify what came with your purchase. Thanks!

This is a known problem. A couple of solutions are proposed in this thread. Restrictor by Michigan Iron, and a flow valve by Stan B. on page 4. I'll probably use the latter. Toukow https://www.tractorbynet.com/forums/threads/kioti-ck3510-loader-issue.414976/page-4

Yeah, if I had them, I wouldn't be asking about them. Guess I'm one of the few who buy paper factory service manuals......

...... a separate envelope containing large, folded, complete wiring schematics similar to photo? Thanks, Toukow

I have the same tractor with 105 hours, so just ran an experiment (friggin’ engineers, don’t ya know!) timing the oil light using a stop watch. I have: no block heater Rotella 15W40 T4 conventional oil 55 F ambient and stable in shop last start 6 days ago time for oil light to go out after...

adfd Thanks for the education. I had always had taken the passing comments that the 3510 and 2610 were the same tractor, except engine size. I guess there are other differences as well. If my list of 'to do's' gets too low, I'll consider trying to fabricate something for mine. Thanks, Toukow

unclesalty-Can you post a picture of the mounting location of the step you have on the right side of your CK2610? I’m confused on this. My dealer said (as of yesterday) there is no right-hand step available, and claimed to have discussed with the Kioti Rep. Here’s a picture of my right-side...

As far as I know, the 3510HST is the same as my 2610HST in this regard. As sea2summit points out, the owners manual on page 7-21 lists 5, tractor only grease points to be done at 50 hour intervals. I'm inferring that the PTO lever you reference is actually the three point lifting lever...

Hello Mangler: I'm a bit lost by your statement, and can only infer a KL4030C is significantly different than a KL4030QA. Your pins have 36mm nuts securing them?

Thanks, Stan, for the solution to this issue. Am I looking at this wrong? I’m not a fanboy of any product- it works or it doesn’t, and my tractor has been great in general. I can understand when manufacturers have issues applying new technologies like emissions, for instance. But if I’m not...

I agree with Roadworthy's and other's comments. Given the hassle of remote dealers, dealer backlogs, etc. you can at least check them yourself to have peace of mind, and plot the correct course of action. Buy a set of the 'Go-No Go feeler gauges' (or simply use a set of regular ones in the same...

Didn't mean to submit the above post, but oh, well.....I would do a quick check and put a finger on the glow plug relay and see if it clicks when turning the key on and temperature below 68 degrees indicating a light LED issue. Oh, I did find the temperature sender and it's located just...

Is your dealer local to fix it? Looking at the schematic, I do not see how the glow plug relay would affect the light indication on the dash, but maybe it's internal to the Preheater Controller seeing current flow to the glow plug relay coil. I would look above the glow plug relay (it's the...

If I'm using the factory manual correctly, it states your engine is a 3F-TM4-U/3F-TH4-U (manual trans/HST trans) and on page 3-9 says 'Maximum/Minimum Speed 2750/850 RPM. For the 3A-165 CK2610 it states it a bit differently as 2600/1150 (+/- 50) RPM. Hopefully it is something simple. Toukow

Yes, there are a number of complaints about the Kioti documentation. I was quoted $160 for the service manual, so I assume it's a money maker. I reviewed the data, removed manufacturer's marks, and added references as to how it was obtained. Hope this works, given the new forum format. For...

zoso2385: I see what I did now. I used the loader owner's manual wherever it called out bolt size or I actually measured the bolt diameter where not specified. There is a bolt torque table in the "loader owner's manual' on pages 13-2 and 13-3, which does NOT include a '9' designation. I cannot...

My fuel filter on a 2019 CK2610 does not match the owner's manual (OM) or the factory service manual (FSM) photos. Both of these show an electrical sensor with associated wires being attached to the bottom of the filter for water detection. I can find no electrical connections on the fuel filter...

I notice that the CK2610HST Kioti manual calls out replacement of the air filter yearly (definitely over-kill for me, given WA), but nothing about the hydraulic and HST filters based on years. It calls for the replacement of these filters at 50 and 200 service hours. I will take a number of...

I was a complete maroon and failed to check my loader bolts in a timely manner on the new tractor. I worked it pretty hard and finally checked them, and some were loose. I felt I dodged a large bullet in that the threaded holes were not damaged, and I was able to torque them properly. I hate...

Per the title, I am hoping you guys can educate me on a few things as far as hydraulics on my new CK2610 HST tractor (30 hours). I wanted to make sure the backhoe was operating a full pressure, hence the gauge installation. I have several questions: 1. I am glad I read in the thread 'Three...

I'm going to do the one year oil change on my relatively new CK2610HST with 22 hours. The owner's manual states on page 7-15, step 9 to 'Run the start motor for approx. 10 seconds to distribute oil to each part of the engine'. In Kioti's great documentation style, I infer they meant 'Run the...

Perhaps a trivial question, but I'll ask just the same. In the past I had read that generally screw type dipsticks are not screwed in when measuring unless specified differently by the manufacturer. As usual I may be missing it, but when I look through the manual I only see the section on how to...

Not sure the approach here is really unorthodox, because I don't really know what the orthodox approach is for this situation. One of the reasons I went with Kioti is Kubota told me I had to sell my 3- point mounted backhoe, and buy theirs for $7k or so. I probably have little use for a backhoe...

I'm hoping you guys can straighten me out. Can you tell me how I'm misapplying the documents at the links? I have attached excerpts from the Miller data (all white documents) at the links, as well as additional Victor tip data (documents with green) . My goal is simply to have the maximum range...

Thanks All for the comments. The frame is back-side welded to the factory frame. The upper cross piece is not welded, but only has about 1/16" gap to the factory cross tube, so is supported when impacted. It would be stronger if welded on the front side too, but I'm really designing for...

Well, here's my shot at it. I thought I should get it done before I had too many hours on the new tractor (currently 7 hours) . Learned the hard way about making sure the 'L' pins are oriented correctly before installing the roll pin. That Chevy engine orange paint by Rustoleum as recommended by...

I'm adding LED's on the ROPS and was trying to figure out where to tap a switched leg for the light relay. Anyway, I only have 7 hours on the beast, and do not have a factory service manual yet. I found some schematics on the forum showing the electrical for the CK35 which I inferred would be...

I'm going to install a mesh grill guard while the tractor is still new, per advice/reminders on the forum. There are some nice designs shown on the forum, many maintaining the ability to fold down the grill guard. I'm not seeing any true advantage of folding, and am thinking of just replacing...

Thanks mtsman2 for the comments! So I gave it a go for the measurement to the edge of the tires, NOT the rims, not the centerline of the rims per the manual dimension noted below. I'm an electrical guy so will defer to the more experienced tractor guys, but I'm not seeing why you cannot...

Since I'm on a roll asking the most basic questions of operational controls on my new tractor, I figured why stop now? I must be using the wrong terms when searching forum, because I do not see this mentioned. As I understand it, the lever in the photo disengages the joystick and stops the FEL...

I'm new to both Kioti's and HST transmissions with a massive 1.5 hours experience, and see no reference in the manual to this component (at least not in the clutch pedal section). Given the fantastic, detailed nature of Kioti documentation (just for fun, check the owner's manual index for such...

Well, I have read somewhere on the forum that if there are no pictures, it never happened, so here is my new tractor. I had bored you previously with a price and option comparison between the CK2610HST and the L2501HST, so this was the end result. Seen one, seen them all to a degree, so I...

Hello All: Can you please educate me on the uses of a tow bar of this size? How are you using it? I'm getting ready to order from Ken's Bolt-on, so thought I'd ask in case I should add something based on your comments. I can only see a 1 1/4" shank tow ball or a very large shackle (my 3/4"...

This post will probably come across as vague and foolish, but I hope you will bear with me. I have a history of buying stuff, not dealing with it immediately, and when the time comes it won't work or is defective and already out of warranty. Granted, sounds like a personal problem, which it is...

Hello Everyone: I've seldom searched for something where I've found so little information about it. I can find a company based in the UK that sells buckets for heavy machinery, and see some postings for this brand for sale (different models, most links don't work anyway). Anyone know anything...

I went and saw my new tractor yesterday, now waiting for the options to be installed. Being new to specifying tractor tires and the associated impacts, I was surprised at how much higher the first step was now that I'd asked for R1's. So I started reconsidering my decision, and the dealer said...

I will most likely pull the trigger this week on one of these two. Searching pricing on the forum makes me envious of other areas of the country. I do not think the Pacific Northwest has great deals on tractors, or I just suck on negotiating deals, which is a real possibility. It's also...

Hello: I'm getting ready to buy a new tractor in the next week or so, and visited two Kubota dealers yesterday, asking option pricing on the L2501HST. I've only owned one tractor in my life, and that's a 1979 Ford 1700, so my hydraulics knowledge is based on that model and that era. It uses a...

Forgive the stupid question, but I'm looking at buying a new CK2610HST in the next week and I've never purchased a new tractor before. Someone here noted to make sure to check any ongoing incentive programs from Kioti, saying dealers do not always tell you about them. So I checked, and found...

Yeah, I'm resurrecting this very old thread. Anyone found anything for a replacement steering wheel? I had seen them on Ebay previously so mistakenly figured I'd buy one when needed. No such luck at this time. Mine has fractured the metal reinforcement, so I figure the remaining ones will be...

stuckmotor: this was not a repetitive action, but I guess it was fast. I was dropping a FULLY loaded bucked about 1 foot when the first one blew. mrmikey-Not sure what looks strange. The first photo below shows the original connection of 3/8" hoses at the transmission housing. I simply moved...

Thought I would toss this out in hopes one of you can see what I am overlooking. I installed a 10 micron hydraulic filter on my tractor and it proceeded to blow the filters within doing 6 lifts with the front end loader. The schematic attached for the Prince SV valve is exactly the system that I...

Now I see how that conclusion could be drawn from the first photo. Here's another view of the seal better showing its cross-sectional shape.

I had recently looked at a new Kubota and liked the additional step offered on newer tractors. My knees aren't what they used to be, so I added the step below to my 1700. I put it at 13" vs 20"of the height of the main foot deck. Obviously it changes the ground clearance, but not an issue for my...

I was going to replace the springs on the shift levers, so was looking at the parts diagram below from Messicks. I noticed the part #47 shown as a seal. I've had hydraulic fluid issues with this tractor so figured what the heck, I'd do those at the same time. So I was surprised that when I took...

I worked on this about five years ago, have a leak, and can't remember the details unfortunately. I have a basic question for anyone familiar with the adjusting components. ITT shop manual says that the box should be filled with 134 transmission fluid, and filled up to the opening plug. Fine. My...

I wonder if this would have any effect, or if I'm just chasing my tail on the matter.....seems like something to remove moisture during heating/cooling cycles would help. I may give it a go if I can find one.

I posted in the New Holland section on looking to sell my Ford 1700 and buy a L2501 Kubota. Given I'm in WA, I figured I'd explore taking advantage of exchange rate and contacted a dealer in Vancouver, BC. I was surprised when he said hew would not sell me a new tractor, only a used one. I asked...

I thought of selling my Ford 1700 for no other reason than accessibility. With size 14 boots and a gut to match, it is not the easiest thing to get in and out of. It has plenty of horsepower for what I need and I've got a few 5 FT wide implements which she handles without issue. I've got her in...

Thanks for suggesting I go step by step on this. I need to study this more, because when I look at the attached layout of my system, and if the power beyond is simply passing high pressure fluid through the loader valve, it would seem the fluid is going directly back to the tranny, which isn't...

Thanks JC for responding. Your posts have been very helpful to me in the past. I just tested the pressure with a 0-5000 PSI gauge at the location you showed and it reads zero. You had stated in the other thread 'You might not read pressure there if lift spool valve diverts all the flow back the...

I'm a novice. I was trying to hook up a three point backhoe to which I've extended the lines 10 feet to help get it into position. I'm standing there and hear the sound of the tractor change. I look around and find one of the extension hoses has fallen off. Things seem jerky on the backhoe so...

Thanks to everyone for the comments. What I ended up doing was buying the Ford OEM kit and had it mailed to my house, as I wanted it back together. But I couldn't return the old kit, as I'd driven in the outer seal, so no way to take that out that seal without leaving marks. FYI: Ebay kit from...

So I decide to repair my leaking front end loader tilt bucket cylinder on a Ford 770 FEL. There is a photo of the seal I'm discussing at the forum link below: http://www.tractorbynet.com/forums/hydraulics/322312-ford-770-loader-cylinder-rebuild-2.html#post3906279 My mistake is ordering a kit...

I'm about to embark on rebuilding the tilt cylinder on a Ford 770 loader that is on my Ford 1700 tractor. At the link below the gentleman encountered issues, which hopefully I will be able to avoid. I'm lucky in that the original poster scanned the page which I assume will be similar for the...