Search results

I’ve been searching for a 3/4”-10 acme nut for the stop on my drill press. The od is 0.745 and threads per inch are 10 as close as I can measure. Help appreciated Photo attached.

Picked up an old used motor to upgrade my Delta Unisaw from 1.5 to 3hp 208 3 phase. The bearings sounded a bit noisy so I pulled it apart to give it a little pm. I was surprised to see how much saw dust was in there being a sealed externally fan cooled motor. I blew it out & removed the...

Our dishwasher stopped running and displayed a low voltage code two days before Christmas 🙁 I opened the electrical box which was included with the dishwasher and this is what I found. The incoming wire is 12 gauge and the screws were found to be tight. I removed the buss & stripped the wires...

I was shopping for a 240V 3 phase breaker and came across a 4 pole 240V breaker. Never heard of such a thing! What would the application for this be?

I was going through my night stand recently & I found a notebook I used to document my recovery from a liver transplant in 1989. It was a card from Massachusetts General Hospital dated 1988 with the cost of rooms in various buildings for private, semi private and critical care for various units...

I have a 2006 Mercedes E320 diesel and I need to replace the glow plugs is there a preferred lubricant anyone uses??

I have two 100cc Partner P100 saws that are that I bought & used 30+ years ago. It’s been in storage because it’s overkill for most work. Fueled it up & it runs flawlessly. It still has the original McCulloch branded chain on it. I’m 69 & can barely pull it over. I gave them to my son who’s man...

My first used saw required a 20-1 fuel mix. I also have an OLD David Bradley that recommended 16-1. I bought my first new saw in the late 70’s a Partner P100 100+-cc’s with a 24” bar It required a 32-1 mix. I then bought a new Jonsered 630 super in 1987 which required a 40-1 mix. I also have...

I’ve been told that a 15~20% moisture content is preferred for firewood otherwise it burns too fast. I’ve burned wood as my primary heat source for 40 years & never had issues with wood that’s too dry, wet yes but NEVER to dry! I found no information that indicates firewood can be too dry. But...

Last year I replaced my concrete garage floor at my house. It was highly polished then sealed it with GHOSTSHIELD SILOXA-TEK 8500 which is a water & salt repellent. Water beads up on sealer and is easily pushed out with a squeegee but is very slippery. I’ve googled solutions and do not want to...

Snow blowing backwards with my compact tractor is challenging me and the F series kubota with heated cab would be perfect but the price for new a new one is out of the question. I found a 2006 Jacobsen turfcat 628d 4wd with heated cab, snowblower & mower for $4500. Supposedly has only 1900...

I’m looking for advice on cleaning & preparing old concrete for GHOSTSHIELD 4500 concrete densifier. Garage is used for auto repair so oils & other fluids have been spilled on floor. I would also like to seal it with GHOSTSHIELD 8500 sealer at some point to protect from road salts. Floor is...

I just removed the old concrete floor and apron in the house garage and I’m putting in a new floor approx 6” thick. I would like to coat/treat the new concrete to protect it from road salts & freezing & thawing. What would you suggest? I’ve looked on line at many products but would like some...

My house has 5 bedrooms & a full bath upstairs. Getting heat upstairs is a problem because the ductwork is by today’s standards too small, uninsulated and runs up an outside cold wall. I’m thinking a mini split may be my best solution. I have a full basement 1/2 is heated and the other 1/2...

I posted this in the Ford forum with no response, hopefully I have better luck here. I think I may have inadvertently damaged the PTO clutch on my Ford 1720 SSS. It was working fine all winter. The left floor board (clutch side) was loose & rusty so I removed it to repair. I built a temporary...

I think I may have inadvertently damaged the PTO clutch on my Ford 1720 SSS. It was working fine all winter. The left floor board (clutch side) was loose & rusty so I removed it to repair. I built a temporary floor board so I could still use the tractor. I was using it one day and not thinking...

I’m working on a 2120 HSS and the transmission dipstick has machine marks in it from contact with a shaft/gear. The dipstick is not bent do I’m asking if this is an occasional issue or a sign of impending disaster. Transmission operates fine. Thanks 90cummins

2 weeks ago I filled a 12 by 72 heavy wall steel pipe with concrete which will be used as a lawn roller. It is open on 1 end and filled with 8 bags of redimix. I used approximately 7 gallons of water in the mix. When will it be safe to put outside in single digit temperatures and not worry...

I made up a set of chains for the 13.6-16 turfs on my tractor using (used) cross links from semi truck tires. They will not stay on the tire because they are too short (15 inches) I need to add at least 4 inches to them so they go over the tread and further down the sidewall. New chains are...

I just rebuilt my old 16hp cast iron briggs with a 0.010 over piston, rod & valve job. And it runs fantastic. I performed a compression test after break-in and recorded 125psi hot and cold. Does anyone know the actual spec or range for this engine. Thanks 90cummins

My new 2019 ZD1211 with 50 hours on it is consistently loosing small amounts of coolant. It has done this since day one and I have documented it to ensure I'm not imagining it. Between mowing's I add 1 or 2 ounces to keep the level at the low level in the coolant reservoir. Oil level shows no...

I did the 50 hour service today so it would be ready to go next spring. Fortunately the mower was on my lift with the new filter ready to install. As soon as I turned it off 2~3 turns it was a flood of oil. I quickly spun the old filter off & the new on on. I still lost approximately 1/2...

I am upgrading my log splitter which I built 40 years ago. I used s tecumseh 10 hp HH100 and a Viking 22 gpm pump. It has operated flawlessly other than being slightly under powered when pushing max pressure of 2500psi which would slowly stall the engine. I rescued a 16 HP 320000 series Cast...

This is the first time my 1720 has not operated properly. I have 3060 hours on it and my 3pt hitch would not raise with a load unless I briefly curled the bucket. The transmission oil is regularly changed so I doubt the oil is the issue. The ambient temperature was in the 30 degree range...

I have a cast iron Briggs&Stratton 16 hp model 325431-0135-03 I am rebuilding it with a new OEM +0.010 piston and rod for my log splitter. I completely disassembled the engine to the bare block and removed the breaker points push rod and installed a magnetron ignition. The Briggs manual does...

Just wondering if they are interchangeable. 90cummins

Adding work lights to my ZD 1211. There is a circuit in the fuse box (With no fuse installed) for auxiliary lights but I can not find the pigtail. Does anyone know where it may be tucked away? Thanks 90cummins

Took delivery of a new 2020 ZD1211 with a 60 side discharge. At first I was looking for used but having never operated a zero turn let alone a Kubota zero turn I decided to look at new machines with 60 months zero interest. With Kubota's optional loan insurance that covers any and everything...

I am looking for an engineering opinion on an OEM replacement connecting rod for a 16hp cast iron Briggs & Stratton model 325431-0135 which is approximately 50 years old. I want to restore it while old stock OEM parts are available. The original rod is usable crankshaft is perfect but I want...

My recently acquired 16hp Briggs&Stratton model 325431-0135 needs a rebuild due to piston scoring from a mouse nest. This engine will be a replacement for my current HH100 tecumseh on my log splitter which runs great however parts are becoming scarce. I have a 0.010 over Briggs piston ordered...

I have an old 16hp B&S cast iron engine model 325431-0135 that I would like to use on my log splitter. I have looked for pump adapters that directly mount on PTO face with no luck. Is there an adaptor that will mount a 22 gpm pump to this beast? I would really like to keep this old iron in...

I have a wards garden tractor with a 16hp Briggs that needs some love. The engine sump is part of the tractor frame. I removed the engine from the sump and noticed there was no gasket. Is the gasket preferred or just sealant? I ordered all new gaskets & seals looking for an informed opinion...

I have a 1/4hp high efficiency motor on my hot air wood furnace and I would like to install a soft start module from Schneider electric to limit the inrush current when it is on my battery backup or my small Honda EU2000i. The motor cycles on& off frequently when the furnace temp is turned...

I知 doing a service on my friends 2120 HSS which has a couple operational issues. Occasionally while operating the transmission will go into neutral then re-engage. Transmission is full and oil and filter have been changed. It has done this for a couple years and does not act like an electrical...

These were out in the woods behind my home which we purchased 30 years ago. They were not used for my home nor the neighbor's. Any one know what they were used for? Thanks 90cummins

I live in the country and my closest neighbor is 200 feet across the main road with another also to the side of me. I have no visible neighbors behind me within 1000+ feet. Would I be able to go outside in my own back yard or would I be confined inside my home? Never thought I壇 be thinking if...

I have a 40 year old Thermo-Built wood furnace with a forced air heating enclosure connected to a SS insulated chimney. It easily heats my 5 bedroom house and the flue temperature is generally less than 200 degrees. I give it a HOT SUPPER at least once a week to keep the chimney clean. I'm no...

My 1720 started having intermittent issues with grinding months ago when starting in cold weather. I removed the starter & found no obvious problems but did notice some oil in the solenoid so I cleaned it to eliminate the possibility of that causing slow engagement, I did noticed 3 spots on the...

My cutting edge is worn out on my 1720 60 bucket and needs to be replaced before I damage it. Looking for a weld on with holes so I can attach a Wicked root rake. Looking for suggestions. Thanks 90cummins

I’ve been working on a friends newly acquired sears tractor with the big ole cast iron briggs. It was constantly stalling after operating on hot days, on cooler days it ran fine. I suspected a bad condenser and replaced it but the problem was still there, so I ordered a new Magneto which is...

I double stack my blades on my 60" Scag for a better cut and recently lost the end of one mulching Gator blade when it went over one smooth rock not a hard hit just a light touch. I place the regular blade on the bottom to protect the gator blade from impact with rocks. The broken piece bent a...

Does anyone have a good recipe for a home made drilling/cutting oil mix. Looking to use something I may have on hand. 90cummins

If you knew North Korea launched a nuke and had 45 minutes to prepare for an EMP attack what would you do?? If I was home I would isolate my home from the grid as much as possible by moving all breakers including the main breaker to the off position. I would unplug everything from the outlets...

A good friend has a 16hp Wards Garden tractor that was complete until 2 months ago when he needed a front wheel assembly for another tractor. The engine runs good and as far as he recalls it drives fine. I've always wanted a big ole 16hp Cast Iron Briggs engine. He has been wanting to give it to...

After 29 years my 1988 1720 SSS needs repair! The power steering cylinder has started to leak so I just ordered the parts from Messicks. It has close to 2900 hours on it and this is the first time it has ever needed repair. It has performed above & beyond it's designed capacity (thanks to the...

I have an off grid battery backup system with two battery banks one is 370ah and the other is 225ah.. I have acquired another set of batteries 3 years old that were left discharged (J185H-AC 225ah) and I'm working on reviving them to add capacity My current battery banks have an amp/hr rating...

Years ago diesel fuel had an indefinite storage life now I知 hearing otherwise because the sulfur content has been reduced. What are the facts about today痴 on-road diesel, off-road diesel and heating oil storage life? I burn so little heating oil now due to other heat sources that I知 starting to...

I built a DC generator to power my 4kw home inverter when the power is out. I bought and rebuilt a 10hp Yanmar L100 diesel that I bought off Craigslist and use it to power a 28v 450 amp Niehoff N1603-2 DC generator to support my 24v off grid inverter. I have the engine turning at 2750 which...

I built a DC generator to power my 4kw home inverter when the power is out. I bought and rebuilt a 10hp Yanmar L100 diesel that I bought off Craigslist and use it to power a 28v 450 amp Niehoff N1603-2 DC generator to support my 24v off grid inverter. I have the engine turning at 2750 which is...

I have 2 Military surplus MEP-952b 28v DC APU's 1 of which is being used to support my battery backup system. These units use a German made Farymann 43f diesel engine rated at 15hp to drive a 280A DC generator. I'm looking for anyone with knowledge that can help me modify the governor for...

On May of 2011 I started a thread in the Yanmar forums titled (Forum for Yanmar air-cooled diesels & clones) that got lost after the website reorganization. Since then I have had several projects that I would like to share. Would it be possible to create a separate Forum for (Air-cooled Diesels)...

Led shop lights. I've been replacing the CFL's in my home with LED's since summer and it's now time to upgrade my shop lights. My shop is 40x60 with 12x12 doors and is poorly lighted. The main lighting consists of (6) 8ft (2x60w) T12 fixtures approximately 10 off the floor. Around my lift I have...

I've a question about water bloc filters. I made a filter assembly for my friend with a 10 micron spin-on filter and a water bloc filter because he recently filled his tractor with water contaminated fuel this summer. Recently it has been around zero for a few days and he couldn't pump fuel from...

Because of poor fuel storage I had to help a friend get his 2120 Ford tractor running because of water in his fuel. To prevent future problems I built him a filter system with a 10 micron particulate filter and a Goldenrod water block to prevent future troubles. That prompted me to upgrade my...

I have 2 Military surplus MEP-952b 28v DC APU's 1 of which is being used to support my battery backup system. These units use a German made Farymann 43f diesel engine rated at 15hp to drive a 280A DC generator. I'm looking for anyone with knowledge that can help me modify the governor for steady...

My ignition coil failed in my Sears Suburban HH120 Tecumseh and they want $200 for a used one on E-bay! Is there a retro-fit kit or after market coil for these?? 90cummins

I知 planning on building a powerhouse for my generators and I would like your input on design details that must be built into it to best serve its intended purpose. First I will describe what I have and my plans. The purpose of my powerhouse is to provide secure shelter for my generators from the...

I'm looking at a 2004 iZ5223 with a Kawasaki FH680V and an asking price of $2000 or BO. I currently have a Scag STHM and it is killing my back. It has 1111 hours on it and looks to be in good condition. I would like some input as far as cut quality and reliability. Thanks 90cummins

We have heated with oil for 60 years and never had problems with it. I have been using it in my tractor for 20 years and never an issue. I've heard that the new low sulfur diesel doe not keep as well as the old formula. I keep (2) 275 gallon tanks topped up and have and additional 3 sealed 55...

My neighbor has a 2120 4wd and was moving logs with his front mounted pallet forks when the right front wheel fell off. Not sure what failed first, bearing pieces were found on the ground. I'm impressed that there wasn't more extensive damage as there was a huge load on it at the time. Parts...

I did a service on a Ford 1910 that had moisture in the transmission oil and have 15 gallons of creamy white colored oil. The oil has been setting for several months with no separation. I have a CleanBurn 2800 waste oil heater and would like to know if its possible to get the oil & water to...

Earlier I started a thread titled (SolarCity installing a 6.37kw system on my house!!!) This new thread is to discuss a Battery back-up System to complement my new Solarcity system. At this point in time any battery back-up system I may install is not compatible with my Solarcity system...

I found this rototiller at the local scrap yard in very good condition but missing the magneto. Looks to have been under cover it's entire life, the gas tank is clean with no rust & the engine turns over easily. Anyone have any info on this or it's value? I feel I may need to save it from the...

I just finished installing a (New) Yanmar L70 (7hp) on my portable 5kw generator which originally was equipped with a Yanmar L90 (9hp) diesel. My question pertains to the fixed losses required to turn the generator at rated speed and energize the field. Other than the increased power required to...

Air cooled engines are designed to operate & survive in temperatures exceeding 100 deg F. My question pertains to extended generator operation in sub-zero temperatures. Air cooled engines would never get close to operating temperature, particularly air cooled diesels like Yanmar that are...

I have an electric heater space heater with (3) 2.5kw heating elements rated at 7.5kw at 208v that I use for load testing generators. It also has a 208v fan motor that uses 0.6amp. I would like to calculate the actual load (watts) due to the increased voltage. Various generators operate between...

I recently signed a contract with SolarCity for installation of a 6.37kw system; work should start in January with the system operational by March. After many questions and additional research I realized that when the grid goes down the solar is inoperative also. I have several generators but...

I've found the above mentioned Yanmar that has an expanded oil sump and oil filter. My research could only find that it had military and/or marine generator applications. Anyone have information on this unit?? Thanks 90cummins

I'm looking at a very nice stationary Yanmar TS105C water cooled single cylinder diesel which produces 9HP at 2200 rpm. I cannot find any information other than it is possibly 70's vintage. I called Yanmar and they have no info on it. It is made in Japan and not a Yanmar clone. Does anyone...

I'm looking at a very nice stationary Yanmar TS105C water cooled single cylinder diesel which produces 9HP at 2200 rpm. I cannot find any information other than it is possibly 70's vintage. I called Yanmar and they have no info on it. It is made in Japan and not a Yanmar clone. Does anyone have...

The reason I ask is because I have a 60 Kuhn rototiller that binds the PTO shaft due to excessive angles when fully raised or lowered depending on how I have it adjusted. My original driveline with slip clutch broke so I installed a regular shaft with no clutch (to finish my tilling) which runs...

I broke the ball end on my top link which I think is from a John Deere based on my e-bay search. I need the LH threaded link end. The thread OD measures 1.095 with 8 tpi and the body alone is approx. 13 inches long. I bought a top link from tractor supply but the assembly it is too long and the...

I found a small fixed speed 3 cylinder Yanmar Thermo-king diesel that has no throttle lever for speed adjustment. I would like to change it to variable speed by replacing the injection pump. Not much information available from engine tags. Does anyone know what is required? Perhaps just a new...

I have a 1988 Ford 1720SSS with FEL that I purchased in 1995 and currently have close to 2300 hours on it. In that time all I have done is maintenance, it has never broken or failed me. I mow, bush hog, snow blow, till, landscape and log with it. The only issue I have had was not enough power in...

I have 120/208 3 phase power in my garage for my 10hp 3 phase compressor and a 3 phase drill press. All other equipment is single phase 120/208. I have a 25KW single phase 120/240 PTO generator and a couple small portables that I would like to use as backup during an outage. I can do without...

Several years ago a neighbor asked if I could check his 1910 Ford that was over heating. He drove it over with the temp guage in the red and steaming. The water pump bearings were so bad the fan tips moved perhaps 1.5" So off comes the water pump to be rebuilt. I installed the rebuilt pump &...

I bought several P100's quite a few years ago & used it to cut cord wood and then cleared a lot with it, I also sold 2 to family members. Well I ended up getting 2 of them back and made 1 good saw for my son who is now smart & strong enough to handle a large saw. We took it out a couple weeks...

How early is too early to start putting wood in for winter? I've been burning wood for years, I have a forced hot air wood furnace in the cellar which is where I also keep my wood. I can store 7~8 cord but need only 4~5 or so. In the past I have put wood in in the fall. Getting older with...

Does anyone have problems with unwanted symbols being inserted after they write a post and spell check it? Below is a recent example of what happens when I post a spell checked post. This requires me to correct spelling again after I post it. I also have problems using the back arrow button...

Fired up my 1720 Turbo to snow blow today! When it's 3 degrees outside and your body parts are freezing that extra power is really nice when you want to get the job done quickly. When pushing it the boost hit 8~10 psi with no smoke and it has that beautiful turbo growl & whine! It now has the...

I just did a major service on a 2120 HSS 12x12, what is the proper way to up shift or down shift on the go? Use the clutch or just change gears? Is the HSS for slow speed F&R loader operation only? It's not my tractor but I would like to know for future reference. Thanks

I submitted a review for my 1720 on 2 occasions with acknowledgments that it was received but still no review posted. Tim

In preparation for Y2K I purchased a Generac XL4000 portable and a Generac PTO 25 generator rated 25kw continuous and 50kw surge for use on my 1720 Ford with 23 PTO hp. To date I have used both with no problems. Due to the recent flooding disasters I have once again been reading posts on...

A couple questions? I have a 1720 SSS with FEL, agg & turf tires which has been a great tractor with about 2100 hrs. It is the perfect size and power (now that it has a turbo) and I have no intentions of trading. The only addition I would really like is a fully enclosed cab. I have heard that...

I recently did a service on a 1910 Ford, engine O&F, front axle and transmission which was milky. I had some Tractor supply oil on hand from a previous service but not enough so I went to NAPA & picked up 10 gallons of their Good (not premium) tractor hydraulic oil at $53.00 per 5 gallons. First...

In 1996 I purchased a Snapper Pro Hydro 52 walk behind with a 16hp Briggs Vanguard which currently has approx 520 hours on it. For years I thought about adding an oil pressure guage but it was always a low priority. Well 3 weeks ago I installed a 100psi gauge. Full throttle cold it runs 70 psi...

I have the above machine listed above and need to replace the spindle bearings, I misplaced my notes with the bearing #. I need the actual bearing # not the snapper p/n I don't want to tear it down untill I have the parts on hand. Thanks Tim

I have a 1720 SSS and RM 59-3 mower which uses a Kevlar belt that is 150" long. The belt runs a torturous path over a bull wheel 2 idlers and three blade spindles with numerous twists/flips. I have replaced the belt at least 5 times in the past 12 years and it is not used commercially. Is this...

I have 2 genuine air cooled Yanmar diesels and a Chinese quiet generator set with an L100 clone. The Yanmar air cooled diesels are excellent engines very well designed, durable and easy to work on. My Chinese quiet diesel generator rated at 6500 watts has however proven otherwise, this generator...

I've been working on my 1720 SSS lately and just finished installing a Garrett 1752 turbo off a Saab, huge difference but a bit on the big side. I僧 looking for a smaller turbo or possibly install a second (twins)!! Any way I was looking at the repair manual because I want to install a 10 micron...

Hi I have a 1720 SSS and have been looking for information on increasing the HP by 5 to 10 and thought I mite try here as I'm sure there will be quite a few opinions pro & con. I have a 60" snow blower and at times could use a-bit more power when busting thru the drifts so I won't need to use...