If you have Toolcat questions, ask them here...

[ruffdog]

Use a slide hammer type seal puller like this one. Drill a small hole in the seal and screw in a metal screw. Use the SH attachment that hooks under the screw head (second from right) and carefully pull the seal.

Slide Hammer and Puller Set, 14 Piece

 

[cemech65]

Thank you ruffdog, i'll let you know how it turns out.

 

[laurencen]

in the past I have used a self drill screw to thread into the seal, usually 2 opposite or 3 evenly spaced and used a pry bar to ease it out, seems on older machines the seals were way better, these new ones are tin and wear faster

 

[aelsnow]

How do I clear the service reminder on my 2021 Toolcat (with a keyless start).

I cannot find instructions how to do it in the service manual.

Are these instructions correct for my machine?

Clearing service reminder??

My 2013 5600 is beeping at me again for the service reminder. How do I shut this off? Can't see it in the manual. BLES

www.tractorbynet.com

 

[ruffdog]

My service manual for my 2017 G series 5610 (section 60-190 Maintenance clock) agrees with the post above with minor changes:

Key OFF (press OFF for keyless), Press the HOURS button to turn the panel ON, Press and hold both HOURS and AUX HYDRAULICS till panel displays reset.

 

[aelsnow]

Thanks. I’ll try to use your page reference to find it my manual as well.

 

[Mister3]

Have a 2007 with 2 codes:
50-73
50-75

Anyone have a code list?

 

[consigliori]

Just replaced the controller on a 5600 Toolcat and now the glow plug and aux hydraulics lights are flashing, the temp gauge is pinned to max...

It starts ok, but won't go into gear or anything else. Lift tilt and traction functions disabled even with arm rest down.

What's going on? Is there a reset procedure for a new controller?

Any help appreciated!!

 

[ruffdog]

Just replaced the controller on a 5600 Toolcat and now the glow plug and aux hydraulics lights are flashing, the temp gauge is pinned to max...

It starts ok, but won't go into gear or anything else. Lift tilt and traction functions disabled even with arm rest down.

What's going on? Is there a reset procedure for a new controller?

Any help appreciated!!

What was the reason for the new controller? Does it have keyless start? Did you double check the connections for loose,broken,bent pins?

 

[consigliori]

Have a 2007 with 2 codes:
50-73
50-75

Anyone have a code list?

50-73 = Throttle Sensor Ch A Out Of Range High
50-75 = Throttle Sensor Ch B Out Of Range High

 

[consigliori]

What was the reason for the new controller? Does it have keyless start? Did you double check the connections for loose,broken,bent pins?

The Enter Code button stopped working on the old controller. Yes, keyless start
Yes, double checked connections as well

 

[consigliori]

33-23 = Controller not programmed

Well now, that makes a **** ton of sense...

Think maybe the dealer I ordered it from would've mentioned that was needed, huh

FFS

 

[ruffdog]

33-23 = Controller not programmed

Well now, that makes a **** ton of sense...

Think maybe the dealer I ordered it from would've mentioned that was needed, huh

FFS

Let us know what happens!

 

[ruffdog]

33-23 = Controller not programmed

Well now, that makes a **** ton of sense...

Think maybe the dealer I ordered it from would've mentioned that was needed, huh

FFS

Also, it makes sense that the controller needs to be programmed to the serial number (master code) so you then can program operator codes (keyless start).

 

[consigliori]

Let us know what happens!

Will do-
Bobcat tech should be here sometime tomorrow

 

[Hersheyfarm]

I have an 2012 rtv1100 and a 2020 svl75(cab).
what expectations should i have by getting rid of these 2 and getting a new tool cat. The svl75 is mainly used to grade my mx track. It’s just another front loader for the farm. The tv is mainly used by my wife in spring for garden and by me after storms for fence repair. Neither get used a lot. The toolcat looks interesting. I would go with the dump bed over the 3 point, all though a grader box would be good for the track. Wife likes the dump. How good can the tool cat dig dirt with a tooth bucket? I also have a heavy kubota root grapple, would toolcat be able to handle that?

 

[Xfaxman]

I have an 2012 rtv1100 and a 2020 svl75(cab).
what expectations should i have by getting rid of these 2 and getting a new tool cat.

I expect that you would really like it and it would do what you need it to do.

The toolcat looks interesting. I would go with the dump bed over the 3 point, all though a grader box would be good for the track.

Put a SSQA plate on the back of the grader box:

How good can the tool cat dig dirt with a tooth bucket?

Very good. This is a 6 foot wide 1 cubic yard bucket:

I also have a heavy kubota root grapple, would toolcat be able to handle that?

Yes, this 6 foot wide Monster Grapple weighs 1,168 pounds:

The loader will lift over 3,000 pounds.

Have you seen this thread? Toolcat 5610 F and 5610 G Series Pictures

Good luck and keep us posted.

 

[ruffdog]

I also had a RTV 900 that I traded in on the toolcat. The comparing the two, the TC is a SUPER heavy duty version of the RTV that also has a construction grade loader arm to do work. It is a niche piece of equipment that can do a lot of different tasks in comfort. Drive one and watch videos....if it fits what you expect from it, it will be an asset.

 

[Mister3]

I have an 2012 rtv1100 and a 2020 svl75(cab).
what expectations should i have by getting rid of these 2 and getting a new tool cat. The svl75 is mainly used to grade my mx track. It’s just another front loader for the farm. The tv is mainly used by my wife in spring for garden and by me after storms for fence repair. Neither get used a lot. The toolcat looks interesting. I would go with the dump bed over the 3 point, all though a grader box would be good for the track. Wife likes the dump. How good can the tool cat dig dirt with a tooth bucket? I also have a heavy kubota root grapple, would toolcat be able to handle that?

I have a 3 point lift attachment for the rear which fits into the receiver hitch, great to drag a scraper or whatever behind which doesn't require PTO

 

[kuypers]

Thank you ruffdog, i'll let you know how it turns out.

I'm having the same issue but in the rear on a 2005 Series What was the final results