J F
Elite Member
:laughing: I can only imagine. 
BX25D. Mod #1 and continued.
- Thread starter 4shorts
- Start date
- Views: 364417
-
- Tags
- kubota bx25d
OP
4shorts
Elite Member
J F
Elite Member
You're losing already, just thinking about getting the little beauty dirty. :laughing: (no pic in your link )
mjncad
Super Member
Using the muffler clamp makes it look OEM instead of an afterbirth that Kubota had with the hose clamp mount.
OP
4shorts
Elite Member
The clamp is certainly stronger. The hose clamp is just ridicules. It looks cheap and is just plain wrong to use especially for a safety item. I'm very surprised Kubota did that. The muffler clamp took five minutes to fab up BUT I will admit I had a solid piece of aluminum square stock chucked in under the boring head of the milling machine to build a custom clamp and said to myself " it don't make sense to spend two hours or more building a clamp when a simple exhaust clamp will more than do it". I figure my idea is just a cost effective as Kubota's but better
rbarker
Platinum Member
The clamp is certainly stronger. The hose clamp is just ridicules. It looks cheap and is just plain wrong to use especially for a safety item. I'm very surprised Kubota did that. The muffler clamp took five minutes to fab up BUT I will admit I had a solid piece of aluminum square stock chucked in under the boring head of the milling machine to build a custom clamp and said to myself " it don't make sense to spend two hours or more building a clamp when a simple exhaust clamp will more than do it". I figure my idea is just a cost effective as Kubota's but better
Yes Paul, but think of all the possibilities like maybe self-leveling and self-centering so it would always be visible from the rear no matter what the position of the back hoe!
. Myself I chose to just remove it completely since the tractor never goes on the road.Sent from my iPad using TractorByNet
varmint
Elite Member
- Joined
- Mar 17, 2003
- Messages
- 2,577
- Location
- Northern Maryland
- Tractor
- Kubota B8200, then a Kubota L3130 HST, now a Kubota L3400 HST
Paul, you missed a chance with that SMV mount: you coulda made something like a ball jointed quick adjustable device, maybe even with titanium (oh yah, that's pretty hard to machine, isn't it?) but I suppose what you did will work fine! Looking forward to the video.
RaydaKub
Veteran Member
Yes Paul, but think of all the possibilities like maybe self-leveling and self-centering so it would always be visible from the rear no matter what the position of the back hoe!
Imagine the possibilities! An electronic tilt meter coupled with an electronic compass that controls a hydraulic system to keep aimed straight behind you no matter the angle or direction of the hoe. A manual override adjustment system so that you could specifically point it in a given direction in case straight behind you isn't really where the traffic is going to come from. Man, I see at least a couple weeks more mod'ing coming up here.
Sent from my iPad using TractorByNet
radioman
Super Member
He's not gonna get that thing dirty after all this.
YUP! he is not .. how sad. A great toy -err tool not being used.
Groan!!!! cat scan .......
Well the light test went well. Had a few seagulls fly into the shop. Guess they were blinded by the light
The clamp is certainly stronger. The hose clamp is just ridicules. It looks cheap and is just plain wrong to use especially for a safety item. I'm very surprised Kubota did that. The muffler clamp took five minutes to fab up BUT I will admit I had a solid piece of aluminum square stock chucked in under the boring head of the milling machine to build a custom clamp and said to myself " it don't make sense to spend two hours or more building a clamp when a simple exhaust clamp will more than do it". I figure my idea is just a cost effective as Kubota's but better
Yeah -- mine snapped off from being caught when digging out a stump. The muffler clamp is genius! I was thinking I shoulda done the same. So - are you going to paint it so it wont rust?
OP
4shorts
Elite Member
Yes Paul, but think of all the possibilities like maybe self-leveling and self-centering so it would always be visible from the rear no matter what the position of the back hoe!
Sent from my iPad using TractorByNet
Imagine the possibilities! An electronic tilt meter coupled with an electronic compass that controls a hydraulic system to keep aimed straight behind you no matter the angle or direction of the hoe. A manual override adjustment system so that you could specifically point it in a given direction in case straight behind you isn't really where the traffic is going to come from. Man, I see at least a couple weeks more mod'ing coming up here.
Sent from my iPad using TractorByNet
I'm disappointed in you fellows. All these great ideas and you never once mentioned an led light to go with them :confused3: :laughing:
Its sprayed with Galvanized spray paint. Doing it that way made it match the rest of the bracket.
:thumbsup: Glad you liked the idea.
Well I never left the shop until 11 PM last night. Editing the video and started the upload. Its 12:10 here now so the video has been uploading for over 11 hours and its up to 84% so it takes time but its a HD vid so what can I say.
Got out to the shop early this morning. Removed the hoe and installed the 3pt hitch and then the Chipper. Had to cut 3" off the PTO shaft and the outer case then I tried it. Holy cow this thing works FABTASTIC!
Just in case you haven't guessed I have to do a mod on the chipper. Hey it's not my fault :confused3:
It really don't drop low enough on the 3pt hitch so I'll fabricate an extension for it :thumbsup:
Here's a few awful looking photos I snapped with the iPhone.
J F
Elite Member
J F
Elite Member
Good god man, you're definitely going to the top of my "hate list". :laughing: Great pics. :thumbsup:
OP
4shorts
Elite Member
Gee that don't sound good. Sure happy I don't scare easy lol
The video is up. Hope the link works because I'm mobile.
2013 Custom Kubota BX25D - YouTube
Cap-n-Cray
Silver Member
Nice Video...
You are missing the arrow on the your bucket for alining the QA. Might want to check with your dealer.
You are missing the arrow on the your bucket for alining the QA. Might want to check with your dealer.
OP
4shorts
Elite Member
Scooby074
Super Member
Not a bad price at all
Cap-n-Cray
Silver Member
I do not have a photo yet because my QA did not come with the sticker when I bought it. The instruction manual show where to install the arrow and how to use it. My dealer has ordered one for me but it has not come in yet. The part number is 7J619-3655-1. There is a whole page on "Attaching the indicator Label."
Future mod... A place to hold the QA pins when not in use.
Future mod... A place to hold the QA pins when not in use.
ultrarunner
Epic Contributor
- Joined
- Apr 6, 2004
- Messages
- 28,913
- Tractor
- Cat D3, Deere 110 TLB, Kubota BX23 and L3800 and RTV900 with restored 1948 Deere M, 1949 Farmall Cub, 1953 Ford Jubliee and 1957 Ford 740 Row Crop, Craftsman Mower, Deere 350C Dozer 50 assorted vehicles from 1905 to 2006
Could using a muffler style clamp make it easier to damage the hydraulic cylinder of one was not careful?
OP
4shorts
Elite Member
Thats a thought :laughing:I do not have a photo yet because my QA did not come with the sticker when I bought it. The instruction manual show where to install the arrow and how to use it. My dealer has ordered one for me but it has not come in yet. The part number is 7J619-3655-1. There is a whole page on "Attaching the indicator Label."
Future mod... A place to hold the QA pins when not in use.
Thanks for this. Ive removed and installed the QC bucket a few times now and thought it was easy enough. I'll check on the decal tomorrow. Thanks for this. Much appreciated :thumbsup:
Na. That clamp would never put enough pressure on that cylinder to damage it.
