What is this?

   / What is this? #1  

gstrom99

Veteran Member
Joined
Nov 4, 2015
Messages
1,733
Location
Greene, Iowa
Tractor
Deere 855, Deere 530R zero turn, Allis Chalmers D17 III, Polaris Ranger, Deere 3032E (SIL's), Yamaha Timberwolf 250, Husky saws, H & H 10k and Carry-On trailers
This saw chain was hanging from a nail in my pole barn, when I bought this place. It's not real long, probably for a 20 - 24" bar, but the chisel teeth are massive and they are spaced at 3". Rusty and I see no numbers on the thing.

What could this be for/from?
 

Attachments

  • IMG_20220110_170134.jpg
    IMG_20220110_170134.jpg
    1.4 MB · Views: 253
   / What is this? #2  
The picture is blurry but I'd say...a chain saw. ;) Perhaps from the 50s.
 
   / What is this?
  • Thread Starter
#3  
I could take a close-up, but it probably wouldn't help... 😬
 
   / What is this? #4  
I am betting it is 3/4 pitch. Was used on handheld chainsaws in the 50-60's but is still used on commercial harvesters. Measure the distance between 3 rivets and see if it measures 1.5 inches and half of that would give you 3/4 pitch.
 
   / What is this?
  • Thread Starter
#5  
I am betting it is 3/4 pitch. Was used on handheld chainsaws in the 50-60's but is still used on commercial harvesters. Measure the distance between 3 rivets and see if it measures 1.5 inches and half of that would give you 3/4 pitch.
Yep. That's what it measures. I was going to scrap it, but looks pretty impressive hanging from the nail. :D
 
   / What is this? #6  
@gstrom99 Yep those large drivers and huge teeth on 3/4 pitch are quite large. Never ran any that size but have ran a couple old chainsaws that had 1/2 pitch on them. Back before they had automatic oilers and you had to push a manual oiler every few seconds when cutting.
 
   / What is this? #7  
@gstrom99 Yep those large drivers and huge teeth on 3/4 pitch are quite large. Never ran any that size but have ran a couple old chainsaws that had 1/2 pitch on them. Back before they had automatic oilers and you had to push a manual oiler every few seconds when cutting.

May have been on those big harvesters. Sounds too big to be on any regular chainsaw even back in the early days. Those saws were beasts, all gear drive and hell on torque but slow. One could really lean on them and throw impressive chips. My big shock when I retired from the AF (21 years) was buying my first new saw. No gear drive. Took a bit of getting used to not haveing the lean on it and the need to keep the chain SHARP!
 

Tractor & Equipment Auctions

2011 WESTERN STAR 4900 SB (A50854)
2011 WESTERN STAR...
2019 TOYOTA 8FGCU25 PROPANE FORKLIFT (A51222)
2019 TOYOTA...
2006 INTERNATIONAL PAYSTAR 5500I KILL TRUCK (A50854)
2006 INTERNATIONAL...
2012 KENWORTH T400 TANDEM AXLE 24FT REEFER BOX (A51222)
2012 KENWORTH T400...
2012 PETERBILT 388 (A50854)
2012 PETERBILT 388...
2019 HINO 155 16FT BOX TRUCK (A50505)
2019 HINO 155 16FT...
 
Top