What did you buy this week?

[Alan W.]

Glad you found replacements.
Ive had luck with stubborn gland nuts by heating the outside of the tube and hitting it around its circumference with a good sized brass hammer. Usually spraying a penetrant in between heating and hammering.

 

[Fuddyduddy1952]

I got this today. Vevor top link. Mine the pipe got damaged and I got tired of fooling with it. I'll keep mine for a spare. I removed that safety catch on it and didn't use hoses or banjo hardware because my hoses connected to it fine. $142 from Walmart online.

 

[sd455dan]

Glad you found replacements.
Ive had luck with stubborn gland nuts by heating the outside of the tube and hitting it around its circumference with a good sized brass hammer. Usually spraying a penetrant in between heating and hammering.

Yes Glad Koyker still makes and sells OEM parts

Yep, I did the peening, and heating, and PB Blaster more than once, cheater tube on the large crescent and also pipe wrench. The only thing that I really had luck with to start them turning was an air hammer to get that first 1/4" of turn. Started by marking an alignment line so I could tell when things were finally starting to turn.

The Gland nuts Koyker uses for some reason are Aluminum... and they are definitely not as tough as steel units.

The other three were not easy but doable without major damage and turning into a 1/2 day nightmare.

Here is a picture of the Gland nut after removal from the cylinder, No damage to the rod, I knew things were likely to get rough so I wrapped the an old bicycle tire inner tube around the rod and taped it as well.

 

[Alan W.]

Yes Glad Koyker still makes and sells OEM parts

Yep, I did the peening, and heating, and PB Blaster more than once, cheater tube on the large crescent and also pipe wrench. The only thing that I really had luck with to start them turning was an air hammer to get that first 1/4" of turn. Started by marking an alignment line so I could tell when things were finally starting to turn.

The Gland nuts Koyker uses for some reason are Aluminum... and they are definitely not as tough as steel units.

The other three were not easy but doable without major damage and turning into a 1/2 day nightmare.

Here is a picture of the Gland nut after removal from the cylinder, No damage to the rod, I knew things were likely to get rough so I wrapped the an old bicycle tire inner tube around the rod and taped it as well.

Yes aluminum sucks. Hopefully you applied some never seize for the next time or next person.

 

[sd455dan]

Yes aluminum sucks. Hopefully you applied some never seize for the next time or next person.

Darn straight. Plenty of anti-seize applied.
I alignment marked the other tractors FEL cylinders years ago on reassembly and went light on the gland nut torque Nothing has ever moved.

 

[Tinhack]

Did you replace that gland nut?

 

[GreyhawkUSA30340]

This week, I bought a Ratchet Rake!

 

[JethroB]

Id look into whether GA sold them without restrictions.
Whats a little smuggling between friends.

Yep Georgia is a no questions asked state regarding grass carp. (Sterilized) I ordered 20 a couple years ago through the local hardware store. 12” fish $10 each. The fish truck comes through a couple times a year for pickup in the store parking lot.

 

[sd455dan]

Did you replace that gland nut?

Waiting to receive Gland nut and seal kits from AG parts Direct.

I did chuck the Gland nut up in the Lathe and cleaned it up quite a bit just in case, but will be installing the new parts when they arrive.

 

[MossRoad]

Full slab of ribs and two sides of baked beans.

 

[kenmbz]

Mini fridge for my sons Dorm room.

 

[TMGT]

Grapple that'll work on both my tractors and parts to repair my drone.

 

[ArlyA]

Grapple that'll work on both my tractors and parts to repair my drone.

A log or brush grapple? if so, please post pics and review.

 

[grsthegreat]

5 racks of ribs to smoke for BBQ tuesday.

 

[MossRoad]

Mini fridge for my son's Dorm room.

We have 3! Youngest was just in town with her husband picking up lots of her furniture we've been storing while they were in Oklahoma. They left a mini fridge because they already have two. ...

they multiply on their own!

 

[WM75Guy]

On Saturday I bought a Land Pride QH16 quick hitch and a Land Pride GS1560 grading scraper for my NH WM25. Today I bought 4 yards of recycled asphalt to start topdressing our driveway. Weight wise that is all my Big Tex 14TD dump trailer can haul in one trip. I could tell it was behind me.

 

[dj1701]

Since the girlfriend left I have purchased an electric can opener, block of knives, silverware set, egg steamer, floor steamer, and a Stihl cordless weed trimmer. I'm sure the list will get bigger as I discover nothing, where there used to be something.

 

[part-time-Farmer-NC]

Since the girlfriend left I have purchased an electric can opener, block of knives, silverware set, egg steamer, floor steamer, and a Stihl cordless weed trimmer. I'm sure the list will get bigger as I discover nothing, where there used to be something.

ouch...

 

[part-time-Farmer-NC]

Just got this assembled yesterday. Aerator/seeder. Those spurs are razor sharp. I am hoping to not have to disc/till up my food plots this year (or from here on out). Lets see how it works out.

Its almost time to seed clover winter peas, radishes oats etc in the plots.

Waiting for the next rain then I'm gonna seed stuff up....

 

[Happy in NC]

I bought 4 yards of recycled asphalt

Where exactly can you get this from? Not even sure how to find in the yellow pages. Is it direct from an asphalt plant or state yard or Road projects?