What are rated speeds for 6000?
- Thread starter Slippy
- Start date
- Views: 3364
MtnViewRanch
Elite Member, Advertiser
- Joined
- Mar 19, 2005
- Messages
- 10,643
- Tractor
- Mahindra 7520, Mahindra 3215HST, Case 580 extendahoe, Case 310 dozer, Parsons trencher, Cat D6,
Have you looked in your owners manual? Sorry that I can't help.
sellercreek
Silver Member
- Joined
- Jul 21, 2007
- Messages
- 178
- Location
- North Central Arkansas
- Tractor
- 2006 Mahindra 6000, 1987 Ford 2910
Fourth or fifth gear will be awfully close at PTO rpm.
Hope this helps.
I think the speed for each gear at PTO rpm is posted on a decal on the inside of the left fender. Need to look at my tractor to be sure.
Hope this helps.
I think the speed for each gear at PTO rpm is posted on a decal on the inside of the left fender. Need to look at my tractor to be sure.
RedRiver
Gold Member
Low 3 or 4 should be the closest @ 2100 rpm
OP
Slippy
Veteran Member
- Joined
- Sep 23, 2002
- Messages
- 1,059
- Location
- Ohio
- Tractor
- Mahindra 6000 4wd; IH x2; NHTC40DSS; International 1086; JD 5115M
Ahh...I found it in the manual. Guess I should have looked there first.
Low range 4th gear ground speed = 4.3 mph
High range 1st gear ground speed = 6.1 mph
These speeds would be with pto at 540, which is about 2100 rpm.
Of course what I would like to have is also something right in between there.
Thanks.
Low range 4th gear ground speed = 4.3 mph
High range 1st gear ground speed = 6.1 mph
These speeds would be with pto at 540, which is about 2100 rpm.
Of course what I would like to have is also something right in between there.
Thanks.
sellercreek
Silver Member
- Joined
- Jul 21, 2007
- Messages
- 178
- Location
- North Central Arkansas
- Tractor
- 2006 Mahindra 6000, 1987 Ford 2910
I've always said the 6000 needs at 4th and a half gear!!! It would be nice to have another slot in between those two.
Glad you found it.
Glad you found it.
OP
Slippy
Veteran Member
- Joined
- Sep 23, 2002
- Messages
- 1,059
- Location
- Ohio
- Tractor
- Mahindra 6000 4wd; IH x2; NHTC40DSS; International 1086; JD 5115M
I agree. 4.3 is a little slow and 6.1 is a little fast to pull my baler. The 6000 does a real nice job pulling it though. Even on the hills it is real does fine.
sellercreek
Silver Member
- Joined
- Jul 21, 2007
- Messages
- 178
- Location
- North Central Arkansas
- Tractor
- 2006 Mahindra 6000, 1987 Ford 2910
Yes, I bale in 4th gear for the most part and that is just about perfect. My 200+ acres are steep and hilly and the 6000 takes it in stride.
Every now and then I wish I had a 6530 with the levers and controls on the side.
Every now and then I wish I had a 6530 with the levers and controls on the side.
OP
Slippy
Veteran Member
- Joined
- Sep 23, 2002
- Messages
- 1,059
- Location
- Ohio
- Tractor
- Mahindra 6000 4wd; IH x2; NHTC40DSS; International 1086; JD 5115M
The forward and reverse lever gets a little old after a while. I have now baled about 500 5x4 round bales. After 5 hours or so of baling I am pretty tired of the forward reverse lever. Thinking of adding a kicker to my baler, but concerned on the hills I might kick one off. I am covered with grass dust as well. Cab would be nice too.
In low range 4th gear the tractor, baler and I are all ready to go a little faster. I am amazed at how fast the baler will eat up the hay, even the clumps.
In low range 4th gear the tractor, baler and I are all ready to go a little faster. I am amazed at how fast the baler will eat up the hay, even the clumps.
MtnViewRanch
Elite Member, Advertiser
- Joined
- Mar 19, 2005
- Messages
- 10,643
- Tractor
- Mahindra 7520, Mahindra 3215HST, Case 580 extendahoe, Case 310 dozer, Parsons trencher, Cat D6,
Maybe you should think about looking at one of the 8560s with a cab, if they ever get out for sale. More gears and clean air, just a thought.
just a thought.