Shibaura SD2043 Hyd problem HELP

   / Shibaura SD2043 Hyd problem HELP #1  

HeyDannie

New member
Joined
Aug 26, 2004
Messages
7
I was brush hogging the other day and noticed fluid spewing out from under the hood. The hydraulic pump had a crack from the mounting base to end base. I replaced the pump with a new pump different design but same mounting and it worked for about an hour and has started leaking at the seam. I have a Koyker lift in the system also. Question can anyone tell me why this is doing this and what to do about it .Please Its getting expensive
 
   / Shibaura SD2043 Hyd problem HELP #2  
Is it leaking at the gasket ?
Try some permatex gasket maker or sealer on it and let it sit overnight before using it. Also did you clean your hydraulic filter screen in the pump & replace the external filter?
Ernie
 
   / Shibaura SD2043 Hyd problem HELP
  • Thread Starter
#3  
Thanks and yes I cleaned the filter and it had fine pieces of metal on the magnets on the filter. The pumps seems to work part time now. It worked great before the first pump cracked. Don't know anything about hydraulics but do you have to bleed them are could their be a part time blockage?
 
   / Shibaura SD2043 Hyd problem HELP #4  
Does it have an outside spin on-off filter ?
 
   / Shibaura SD2043 Hyd problem HELP #5  
Check Hydraulic Fluid Level. Did you add fluid? Make sure you did not mix 2 different types of hydraulic fluid. Sounds as it is foaming and would cause the fluid to aireate and when it does... the hydraulics will not work. I bet if you drain the fluid and put in the correct fluid this will correct your problem.

Jim
 
   / Shibaura SD2043 Hyd problem HELP #6  
The 2043 does not have a spin on filter; filter is in a canister on top of the pump. There is a bolt on top of the filter you remove to prime the pump. Fill it to the top. Make sure your tranny is full of fluid also. Sounds like low fluid to me.

Buck
 
   / Shibaura SD2043 Hyd problem HELP
  • Thread Starter
#7  
No just the one filter before it enters the pump.. Thanks
 
   / Shibaura SD2043 Hyd problem HELP
  • Thread Starter
#8  
Clean fluid from Atwoods no mix, and when I check it its clear no foam.
 
   / Shibaura SD2043 Hyd problem HELP
  • Thread Starter
#9  
The pump is new the one I replaced had cracked. I did prime the pump before starting and had the fluid level at the proper level. Thanks Buck...Dannie
 
   / Shibaura SD2043 Hyd problem HELP #10  
Dannie, call me and lets get to the bottom of this.

509-521-1507 evenings are best

Buck
 

Tractor & Equipment Auctions

2017 Ram 5500 Valve Placer Bucket Truck with Versalift STP36NE - 41FT Working Height, Low Miles (A51039)
2017 Ram 5500...
2011 GR TRAILER GOOSENECK (A50854)
2011 GR TRAILER...
2015 Kenworth T400 T/A Vactor 2100 Combination Sewer Jetter Vacuum Truck (A50323)
2015 Kenworth T400...
2016 Ford F550 4x4 Bucket Truck with Altec AT41 - 46FT Rotating Bucket and Jib Winch (A51039)
2016 Ford F550 4x4...
2012 FREIGHTLINER CASCADIA (A50854)
2012 FREIGHTLINER...
2018 VOLVO VNL SLEEPER (A51222)
2018 VOLVO VNL...
 
Top