LK3054 accelerator lever question

hogwash · Jun 26, 2022

I purchased my first tractor past weekend and after spending a week using it. I noticed the accelerator lever that you push forward/backwards seems to not make contact until until almost half way forward. My opinion is the lever was pushed too hard and bent the rod back.

What ends up happening is the accelerator arm is only able to push the RPMs to around 1800.

I know the silver stop bolt/nut seems like it's being hit but it's not and i even moved it up to make sure.

Would you pull the lever off, heat it up and bend it up so it hits the C plate earlier?

Thanks in advance,

John

K5lwq · Jun 26, 2022

What about when you use the foot pedal? Does it go to a higher RPM?

hogwash · Jun 27, 2022

K5lwq said:
What about when you use the foot pedal? Does it go to a higher RPM?

Yes. Since it's connected to same C plate (metal rod on left side), it will effortlessly pull the plate counter clockwise and can reach max RPM (verified looking at throttle connection on engine)

K5lwq · Jun 27, 2022

I will have to look later today but I think there a way to adjust the link to the petal. You will need to adjust both that linkage and the linkage to the injector pump. I do not believe anything bent.

K5lwq · Jun 27, 2022

Okay I have your solution. See pictures below.

First you need to loosen the nuts on the linkage I circled in red. Back out on the nut on the left to about where the one in the picture is located. Then adjust the nuts on the right tight against the lever. This will cause the foot petal to come higher off of the floor indicated by the arrow.

Do not worry about the petal getting higher because the actual engine speed is controlled by this stop circled in red on the injection pump.

That will allow The hand throttle to open the tractor up all the way. Just adjust the length of that rod till the hand throttle pushes the injection rack against the stop.

Hopefully that is clear enough for you to fix.

hogwash · Jun 27, 2022

K5lwq said:
Okay I have your solution. See pictures below.

First you need to loosen the nuts on the linkage I circled in red. Back out on the nut on the left to about where the one in the picture is located. Then adjust the nuts on the right tight against the lever. This will cause the foot petal to come higher off of the floor indicated by the arrow.

Do not worry about the petal getting higher because the actual engine speed is controlled by this stop circled in red on the injection pump.

That will allow The hand throttle to open the tractor up all the way. Just adjust the length of that rod till the hand throttle pushes the injection rack against the stop.

Hopefully that is clear enough for you to fix.

Thanks for the good pics and explanation. I tried your recommendations and when I do, it does move the C plate closer to the throttle lever, just like you said. but what it does is keep the foot pedal too far away from the foot pedal return spring. (see the arrow pointing to raised gap). so the pedal return spring doesn't function like it should

Seeing how everything lines up, it seems like the pedal is supposed to sit flush in that return spring channel. when I do that, I am back to the original problem.

hogwash · Jun 27, 2022

I'm thinking I might just use some vice grips to hold a temporary piece of metal in place to see how it reacts with a the metal rod moved a bit. I wanted that to be my last option.

K5lwq · Jun 28, 2022

I would not worry about the spring. It will sit in there when you push the throttle lever forward a bit. I would not try to bend it at all.

hogwash · Jun 28, 2022

K5lwq said:
I would not worry about the spring. It will sit in there when you push the throttle lever forward a bit. I would not try to bend it at all.

Does your hand throttle hit max rpm when in the full forward position? Can to take a picture of the C plate when you push the hand throttle forward to the max? I want to see where your hand throttle is hitting the C plate. Thanks.