I am replacing the head gasket on my Universal 640 DTC. This is a romanian built tractor same thing as a Long brand and the engine is a 60-70 Hp four cylinder Fiat diesel with two heads. It is my understanding that this is the same engine used in a White 1370. I have been told to grease the head bolts before I put them in and tork them. What type of grease should I use. Anybody else work on these engines and have any advice/tips?
Head gasket replacement
- Thread starter BJOHA
- Start date
- Views: 6988
6thgpSF
Gold Member
I can't help you on your engine but I did replace the HG on my Yanmar once and the manual said to coat studs,head bolts and nuts with clean engine oil. hope that helps a little...russ
RoyJackson
Rest in Peace
- Joined
- Nov 17, 2001
- Messages
- 23,144
- Location
- Bethel, Vermont
- Tractor
- John Deere 4052R Cab,, Deere 855D UTV, Z920A Zero Turn Mower and assorted implements
Use an anti-seize compound.
You'll want to retorque those heads after a short period of time (figure 10-15 hours of use).
You'll want to retorque those heads after a short period of time (figure 10-15 hours of use).
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
if wet studs.. I'd use a ptfe sealer.. like gasoila.. if blind studs.. i'd be carefull of putting much of anything on them due to hyd lock. I've seen corners of blocks busted out because of that.
in the end.. it's usually safe to follow the service manual..
soundguy
in the end.. it's usually safe to follow the service manual..
soundguy
David-Davies
Silver Member
Hello BJOHA. I was told by a machine shop to use thread sealent, on the threads, and under the head of the bolts. This seals the bolts from leaking, and you must lubercate the under side of the bolt head to get a proper torque.
David-Davies
David-Davies
how will I know if they are blind studs or wet studs? Mine has large bolts that goe down through the head, not studs that stick out of the block. Does that help?
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
blind or thru.. should be easy to tell. 'wet' bolts go into the water jacket.. blind ones stop at metal.. you don't use a sealer on blind holes.. etc..
soundguy
soundguy
Just use a little oil not enough that it runs off and all will be well the most important thing is to follow the correct sequence when torquing them up most engines are a few stages to get to the correct torque may be a couple of torque fig's might be a torque then so many degrees
there is a good chance there will be more than one size of bolt so there will be more that one fig
so a workshop manual and little oil
You will prob require new bolts as well as most head bolts are stretch bolts
(Think i should have confused things enough now my work here is done:confused2
there is a good chance there will be more than one size of bolt so there will be more that one fig
so a workshop manual and little oil
You will prob require new bolts as well as most head bolts are stretch bolts
(Think i should have confused things enough now my work here is done:confused2
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
replace any waisted bolts too..
soundguy
soundguy
