Ford NH 1320 Overfull crankcase/low Hydraulic
- Thread starter welder1
- Start date
- Views: 9375
redneckford
Platinum Member
yes if the seal in the front of the hyd. pump goes out it will pump oil into the crankcase
JC-jetro
Elite Member
I have and it is relatively easy if no permanent damage is done to the pump. look the link below. Disregard first page till you get to the pump overhaul part.
JC,
http://www.tractorbynet.com/forums/new-holland-owning-operating/90819-my-f-1700-testing-my.html
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
I'd also like to add that you need to find out why the pump shaft seal failed.
Was it just a wear issue and went? or was the pump deadheaded perhaps by a bad hyd valve, non operational relief or relief set to high.. or perhaps even a mis-seated quick disconnect.
on a positive displacement pump, it doesn't take much obstruction to pop a shaft seal.. oil has to go somewhere.
good luck on the issue. post back what you find.
soundguy
Was it just a wear issue and went? or was the pump deadheaded perhaps by a bad hyd valve, non operational relief or relief set to high.. or perhaps even a mis-seated quick disconnect.
on a positive displacement pump, it doesn't take much obstruction to pop a shaft seal.. oil has to go somewhere.
good luck on the issue. post back what you find.
soundguy
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
have you only used it a few minutes and it filled up quick.. or was it a few hours use with gradual fill up?
did 3pt or other remote hyds work normal?
if it was a slow leak.. it might simply be a tired seal. do check the shaft as well for damage or wear where the seal rides.
soundguy
did 3pt or other remote hyds work normal?
if it was a slow leak.. it might simply be a tired seal. do check the shaft as well for damage or wear where the seal rides.
soundguy
It was a slow leak. Crankcase level looks to be a quart/quart 1/2 high. Hydraulic reservoir is barely showing on the dipstick. I last checked the fluids maybe 6 hrs run time ago and everything was OK. Lift worked normal. It will still raise my 5ft. bushhog at idle.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
slow leaker then.. not a catastrophic dead head.
soundguy
soundguy