WranglerX
Super Member
You win, missed the "locking pin" comment in original post...
Counterweight build
- Thread starter Aquamoose
- Start date
- Views: 9653
OP
Aquamoose
Platinum Member
It’s all good. I too have skimmed conversations and based replies on pics I’ve seen.
71bronco
Gold Member
Instead of welding hooks on I would weld a 3 x3 angle iron on the top with slots cut in vertically every 6'' or so. Will hold chains better than hooks.
A hitch would be nice too.
Jeff
A hitch would be nice too.
Jeff
Nice project - CLEAN work and EXCELLENT welds. good job. You may have come close to answering the question - How to add ballast and use 3 point. If it was not quite as tall and had pins on the back. Maybe. Like to see it when you have it painted. And, of course total weight.
ruffdog
Super Star Member
- Joined
- Dec 31, 2011
- Messages
- 10,685
- Location
- southern wisconsin
- Tractor
- Bobcat Toolcat 5610G, Deere X744, Cub Cadet IH 982
Nice and big.....get behind it if someone is shooting at you.
kpsp50
Silver Member
Nice build 
OP
Aquamoose
Platinum Member
I admit I have OCD in the design while fabricating brackets & such to the ballast. I’ve got done figuring out what I’d like to store on it while not overly “crowding it” with unnecessary items. I did add two hooks up front. I don’t plan on skidding anything
The following will be carried:
- 20” Husky Rancher
- Choker
- 8 ft 5/16” binder chain
- Logging tongs
- Timberjack
- Small box to hold odds n’ ends
My smaller 16” Stihl, oil/gas, and bar chain oil already has a place on the tractor.
Progress pics… it’s primed so it’s NOT the final color.
Stay tuned!
The following will be carried:
- 20” Husky Rancher
- Choker
- 8 ft 5/16” binder chain
- Logging tongs
- Timberjack
- Small box to hold odds n’ ends
My smaller 16” Stihl, oil/gas, and bar chain oil already has a place on the tractor.
Progress pics… it’s primed so it’s NOT the final color.
Stay tuned!
Smokeydog
Elite Member
Great fabrication. Nothing beats specially designed and built equipment.
Built a 3pt weight 40 years to help 2wd tractors log and FEL work. Hot water heater tank filled with scrap steel, RR rail and concrete. Plate bottom. Often had to skid the ballast on the ground using to balance and sometimes lower the center of gravity. Pulling logs chained high, hand on 3pt lift to control front end lift and steering with rear brakes. Ballast dragging on the ground when needed. My point being, think about how your ballast engages the ground. Might want some ski, edge tamer type ends on your feet? Don’t want it digging in unnecessarily.
Long tool, like cant hook or ax holder?
Hooks for buckets always helpful. Buckets are my portable tool and part boxes for a variety of jobs.
Built a 3pt weight 40 years to help 2wd tractors log and FEL work. Hot water heater tank filled with scrap steel, RR rail and concrete. Plate bottom. Often had to skid the ballast on the ground using to balance and sometimes lower the center of gravity. Pulling logs chained high, hand on 3pt lift to control front end lift and steering with rear brakes. Ballast dragging on the ground when needed. My point being, think about how your ballast engages the ground. Might want some ski, edge tamer type ends on your feet? Don’t want it digging in unnecessarily.
Long tool, like cant hook or ax holder?
Hooks for buckets always helpful. Buckets are my portable tool and part boxes for a variety of jobs.
OP
Aquamoose
Platinum Member
Just about! I now want to add a certain finishing touch,… you’ll know when you see it. Now I wait for the paint to dry…