BX25 Harbor Freight Quick Hitch
- Thread starter Artisan
- Start date
-
- Tags
- kubota bx25
I have looked all over for a set of shorter pins for mine and I can't find any shorter that 4 1/4 like you got. I think they will be some hard drilling. I have a spare set of 4 1/4 x7/8 pins I may use until I can find something else.
Here is a 4"
RED HANDLE HITCH PIN 7/8 X 4
Here is a 3.5" but a swivel mechanism, not a pin...
McMaster-Carr
Here is a plain Clevis pin, no handle, 7/8" Diameter w/ 2-5/8" Usable $5.04 EA
Mcmaster.com #98306A593
I wonder if the Land Pride QH-15 QH Comes w/ nice lower pins?
I guess I need to dig up a parts list, anyone have a parts list for
a Land Pride QH-15 QH?
RED HANDLE HITCH PIN 7/8 X 4
Here is a 3.5" but a swivel mechanism, not a pin...
McMaster-Carr
Here is a plain Clevis pin, no handle, 7/8" Diameter w/ 2-5/8" Usable $5.04 EA
Mcmaster.com #98306A593
I wonder if the Land Pride QH-15 QH Comes w/ nice lower pins?
I guess I need to dig up a parts list, anyone have a parts list for
a Land Pride QH-15 QH?
NHmitch
Platinum Member
Hi Artisan,
That looks great. Have you tried using these? Category 2 to 1 Lift Arm Bushing - 0268454 | Tractor Supply Company I have to use them with my fast hitch, and they slide right over my existing pins. They work great. Anyways, nice job with the welding!
That looks great. Have you tried using these? Category 2 to 1 Lift Arm Bushing - 0268454 | Tractor Supply Company I have to use them with my fast hitch, and they slide right over my existing pins. They work great. Anyways, nice job with the welding!
Mitch I guess I wasn't clear. The KK Blade where I made those metal
bushings? Well those "Extend" the lower implement draw pins by about
2" each, w/o them the QH bottom hooks do not reach the Implement.
So they extend and bring up to size. I am not done w/ them and
I have not elaborated on them on purpose. I should get the
.5" x 1.5" roll pins I want for them today I would think. After
I do there will be a better explaination, but to answer your question
yes I have seen those and I am not thrilled about them, I have
seen them in all flavors/sizes I should say.
I ran into an interesting QH Top QC that has promise HERE.
Here is a pic of it;
That would stop the top from wanting to jump "almost" out.
I am not done thinking about that yet.
I also found a 7/8" x 3.5" plain pin but below it on the same
page there are some stop collars...HERE. (I am not sold on
that issue yet either. )
bushings? Well those "Extend" the lower implement draw pins by about
2" each, w/o them the QH bottom hooks do not reach the Implement.
So they extend and bring up to size. I am not done w/ them and
I have not elaborated on them on purpose. I should get the
.5" x 1.5" roll pins I want for them today I would think. After
I do there will be a better explaination, but to answer your question
yes I have seen those and I am not thrilled about them, I have
seen them in all flavors/sizes I should say.
I ran into an interesting QH Top QC that has promise HERE.
Here is a pic of it;
That would stop the top from wanting to jump "almost" out.
I am not done thinking about that yet.
I also found a 7/8" x 3.5" plain pin but below it on the same
page there are some stop collars...HERE. (I am not sold on
that issue yet either. )
Zebrafive
Super Member
I'll bet the John Deere QH has some nice lower pins. Not sure how you would find it on JDparts.com
Zebrafive
Super Member
Mitch I guess I wasn't clear. The KK Blade where I made those metal
bushings? Well those "Extend" the lower implement draw pins by about
2" each, w/o them the QH bottom hooks do not reach the Implement.
So they extend and bring up to size. I am not done w/ them and
I have not elaborated on them on purpose. I should get the
.5" x 1.5" roll pins I want for them today I would think. After
I do there will be a better explaination, but to answer your question
yes I have seen those and I am not thrilled about them, I have
seen them in all flavors/sizes I should say.
I ran into an interesting QH Top QC that has promise HERE.
Here is a pic of it;
That would stop the top from wanting to jump "almost" out.
I am not done thinking about that yet.
I also found a 7/8" x 3.5" plain pin but below it on the same
page there are some stop collars...HERE. (I am not sold on
that issue yet either. )
The pictured part is for a top link, implement end. It requires a ball on the implement top pin. Were you thinking of mounting it to the top of your QH and hinging it to drop down and hook up the top implement pin? Seems that would turn your QH into a SH (slow hitch)
Zebrafive
Super Member
Let us know if the pin can be drilled.
gtrippleb
Gold Member
Here's the picture of a JD QH
Item 6 in the picture is what I think you're talking about.
Part #: PM9206
Description: Lower Link Pin
View attachment JD_Category1QuickHitch_PartNumbers.pdf
You can get the part numbers here https://jdparts.deere.com/partsmkt/document/english/pmac/5998_fb_Hitches_Quick.htm
and do a search on https://jdparts.deere.com
1savoy
Gold Member
- Joined
- Oct 27, 2003
- Messages
- 382
- Location
- Oklahoma
- Tractor
- B26, ZD323-60 and JD JX75 currently. Previous: L3800 HST w/ BH77, JD301-A , JD450C Dozer, JD 330, JD F525, Ford 4000, Farmall H
Looking nice Artisan. I used the pins that are second from the top right in the link when I built my grapple. They were easy to cut to length and drill. I do not think these pins are hardened. My guess is they prefer them to bend instead of snap off, but that is just my not knowing guess. Keep up the great work.
Agri Supply - Search
Agri Supply - Search