Bush Hog 2515 wide angle double yoke repairable?

[TigerFanatic1]

I have a lot of movement and visible damage in the wide angle double yoke, likely from getting stuck and damaging from angle. I haven't attempted to take apart yet, because I can't find any bearings or repair kits. The wide angle double yoke looks to be part #76357.

 

[TractorTech]

The cross kits are PN: 64663 anywhere from $46 to $125 depending on where you buy. Messicks has the pricier Bushhog cross, Amazon the cheaper. Most good bearing shops should be able to match.
Could also measure cap diameter and cross length to look up replacement. Measurements are metric. Cheaper route.

 

[TigerFanatic1]

I’m probably misidentified it. Below is a picture

 

[TractorTech]

I’m probably misidentified it. Below is a picture

Oh, well a picture makes the difference. This should be the right one. At $302. vs almost $950. for Bushhog sourced one. Take some measurements to make sure.
Center yoke - Parts
Series 6 parts - SIZE 6 Series Ag PTO Parts

 

[ruffdog]

Many driveshaft CV joints have a cup grease receptacle to grease the center ball. I don't know if yours had it though. (video)

https://www.google.com/search?q=cv+joint+grease+point&sxsrf=ALiCzsYmGvrBGNARLWvAO3OMwe2N9UXNlA:1665792613286&ei=ZfpJY8uAEcymptQP7L6A6Ak&ved=0ahUKEwiLx--H-eD6AhVMk4kEHWwfAJ0Q4dUDCA4&uact=5&oq=cv+joint+grease+point&gs_lcp=Cgdnd3Mtd2l6EAMyBggAEBYQHjIFCAAQhgMyBQgAEIYDMgUIABCGAzIFCAAQhgM6CggAEEcQ1gQQsAM6BwgAELADEEM6DQgAEOQCENYEELADGAE6EgguEMcBENEDEMgDELADEEMYAjoFCAAQgAQ6BAgAEEM6CAgAEIAEEMkDOggIABAWEB4QDzoFCCEQoAFKBAhNGAFKBAhBGABKBAhGGAFQrwZY5xZggRloAXABeACAAcYBiAHhB5IBAzAuNpgBAKABAcgBEcABAdoBBggBEAEYCdoBBggCEAEYCA&sclient=gws-wiz#kpvalbx=_h_pJY_3MHpCqptQP2q2d-A0_48

 

[TigerFanatic1]

Oh, well a picture makes the difference. This should be the right one. At $302. vs almost $950. for Bushhog sourced one. Take some measurements to make sure.
Center yoke - Parts
Series 6 parts - SIZE 6 Series Ag PTO Parts

Thank you so much!

 

[TigerFanatic1]

Many driveshaft CV joints have a cup grease receptacle to grease the center ball. I don't know if yours had it though. (video)

https://www.google.com/search?q=cv+joint+grease+point&sxsrf=ALiCzsYmGvrBGNARLWvAO3OMwe2N9UXNlA:1665792613286&ei=ZfpJY8uAEcymptQP7L6A6Ak&ved=0ahUKEwiLx--H-eD6AhVMk4kEHWwfAJ0Q4dUDCA4&uact=5&oq=cv+joint+grease+point&gs_lcp=Cgdnd3Mtd2l6EAMyBggAEBYQHjIFCAAQhgMyBQgAEIYDMgUIABCGAzIFCAAQhgM6CggAEEcQ1gQQsAM6BwgAELADEEM6DQgAEOQCENYEELADGAE6EgguEMcBENEDEMgDELADEEMYAjoFCAAQgAQ6BAgAEEM6CAgAEIAEEMkDOggIABAWEB4QDzoFCCEQoAFKBAhNGAFKBAhBGABKBAhGGAFQrwZY5xZggRloAXABeACAAcYBiAHhB5IBAzAuNpgBAKABAcgBEcABAdoBBggBEAEYCdoBBggCEAEYCA&sclient=gws-wiz#kpvalbx=_h_pJY_3MHpCqptQP2q2d-A0_48

Mine does have a grease fitting and after looking at the manual, I didn't grease it nearly enough. I'm certain that is a contributing factor also.