Basement Project

[JSUnlimited]

Very nice work. So just how much beer has it taken to get to this point?

 

[beenthere]

RobS
Great project.
Just had some drywall work finished (painter did it) and he used something that didn't require dusty sanding (he said there would be no dust, and it was a wet sanding method). I didn't see him do it, but it looks great and there was no dust. Thought you might like to know, if not already.

I also noticed your window wells, looks like the corrugated window well units. If so, what did you cover them with? Or going without covers - i.e. problem with animals, kids, etc getting in to them, as well as snow and rain. My son has these, and we fashioned some plastic corrugated covers, that really are only temporary (for three years now /forums/images/graemlins/wink.gif ). Wondering if there are any commercial products for covers.

 

[Highbeam]

I use the plain old paper tape but have seen the adhesive mesh type that doesn't require any skill at getting both sides of the tape mudded yet not so much mud that the joint sticks out. I'd like to try it to see how it goes. My biggest trouble is hiding those joints.

 

[rswyan]

</font><font color="blue" class="small">( and he used something that didn't require dusty sanding (he said there would be no dust, and it was a wet sanding method). I didn't see him do it, but it looks great and there was no dust. Thought you might like to know, if not already. )</font>

I normally use just a flat rectangular sponge .... and a bucket of warm water to rinse it in. /forums/images/graemlins/grin.gif

 

[RobS]

mega_me, it's only taken one round of beers so far. I've done all the work myself other than having four buds over to get the sheetrock into the basement. Those big windows were worth it!

beenthere, the windowells came with and there are grates over them that must have been part of the package. They are made of steel strip and rod stock. Pretty simple with tabs around the edges to sit on the corrugated windowell.

Another future project is to remove the steel and make a more decorative windowell with landscape block. Also, I'll taper it more to let more light in.

I've heard of sanding with a sponge but not had success with it. I don't do much sanding between coats, only the finish coat. Unless of course, I goof up. I've also heard of another method that mixes latex paint, plaster of paris and drywall mud (?) to make a one step joint. I can't remember the name, but it sounded pretty tricky for an amatuer like me /forums/images/graemlins/smile.gif

 

[beenthere]

Thanks
About the mud, my son also tried taping and mudding his drywall (he did great putting that up) using the mud in buckets from the box store. He ran into a lot of trouble because it was too thick and didn't realize it. The joints were not turning out well, and the job too overwhelming, so he found a drywaller with some time between jobs. What he mixed up was real thin mud, and the job looked easy.

Good luck with the project. It will be great to have it done, but also fun doing it.
(Now, back to my project of going into the attic 'crawl' space and running a new wire into a light fixture that is about 4' from the outside wall under a 5:12 pitch roof. Not looking forward to doing it, but no alternatives come to mind in this 10° temp. and fiberglass insulation. Yuucckk! ) /forums/images/graemlins/wink.gif

 

[Farmwithjunk]

Sometimes the tools professionals use to make their work look better or go faster are just the ticket for amatures or part-timers. Recently, I did some drywall work in my home. I rented a toll made by Porter-Cable. It is a dust-less power drywall sander. It employs a wet-vac attached to a sander that will sand faster and smoother than any hand sander I've ever used. I'm told most good rental marts have them nowdays.

I also have an account with Ames Tools. They rent "drywall Bazooza's" They will apply mud and tape at an incredable pace. The only drawback is clean-up time. Unless you have a lot of mudding to do, they take longer to fill and then clean out than the job takes with conventional tools.

But that dustless power sander is all that AND a bag of chips!

 

[MossRoad]

Looks like fun, Rob! I'd love to help but the wife frowns on me working on other people's projects when I have so many to finish, myself. /forums/images/graemlins/tongue.gif

Get a good, wide knife for the final pass on the joints. And make many thin coats VS a couple/three thick ones. I had a sander with a dust pickup on it that worked great until my brother-in-law burned it up. /forums/images/graemlins/mad.gif Those work very well, especially if you get lots of hose and place the shop/vac outside. Then, virtually no dust gets recirculated in the house by the vac.

 

[_RaT_]

Looks like a great place. I want one!

 

[hazmat]

It's coming along Rob /forums/images/graemlins/cool.gif. Wish I was at the drywall phase on my attic project. So far, just planning & a heating/AC quote /forums/images/graemlins/crazy.gif... After 4 months I really understand the phrase - "slowing/settling down to start a family"