wiring

Seems I'm encountering many situations where I need to splice 12 volt accessory wiring (spreaders, sprayers, battery maintainers, etc.). In some cases, I just need to add a new SAE plug to the 2-wire cable. Does anyone have a good, clean way to do this? I have tried twisting/soldering wires...

I got a Ford 9n, and it had 2 big wires I think it was 2, 1 ran onto the generator, the other attached to the coil, they were pretty bad so I took em out. But I can't find ny new ones, they are pretty long they run from the generator and coil to around the starter solonoid i think. they run in...

Hi I'm looking a complete farmall 140 12v alternator wiring diagram.

I have power to the distributor from the coil; power to the points; but no fire to the plugs. At least, according to my HF plug wire testor which has never shown spark to anything I've been troubleshooting. 🤔 Everything is new from the fresh wires on the ignition switch out; new coil, points...

Hello and a Happy Easter to all from Wales, UK. New here so I hope I’m doing it correctly! I’m looking for a wiring loom for my Detroit MF 150 with alternator. An Indian supplier has offered one for a 135 but I don’t know at the moment if that is for a US or UK 135 and if US how similar it will...

Was wondering if anyone has this wiring schematic for this series Zero turn. I have a (No Start) issue and feel confident that one of "the many" safety switch(s) is faulty. However it is much easier to troubleshoot knowing where these wires lead. Thanks Don

Afternoon all. Just bought a 2004 TC30 in abused condition - but it started and runs. Able to finish some work I wanted to get down and am now working on getting it back to good condition. Started on the wiring and have the schematic which of course didn't match what had been done to the...

Newbie here just bought B7100 other sure what year. Problem is wiring to ignition glow plugs thought it was the battery 2017 so I replaced and I messed with the wires and it came on. I started today and it clicked it turned and dead No red light, so messed with wires and glow plug light comes...

Hi I have a low hour T474 with Cab. Ive suddenly lost power to the Sterio and gauge cluster for wipers and front/rear spot lights. But still have functioning Heat/AC also ceiling mount controller. I hit a bump, and all came back on.. Hit another bump, yup.. off the 2 went again. The mystery...

Hey everyone my Ford tractor has a thermostart feature and I don't know where to wire it, wiring it directly to the ignition switch like on Massey Ferguson tractors wouldn't work since this particular ignition switch only has three modes OFF/ignition ON/Start, normally you'd want the switch to...

So the dogs discovered that our trailer's wiring plug was a great toy. They tore the entire front third of the wiring out. Oddly enough I had moved the trailer up to a work space close to the barn so I could fix a minor problem. It's a 14'x77" utility with HD Axle and brake. Need some...

Cannot get a spark on this machine, and cannot find the fusebox. All the other electrical components seem OK, has fully charged battery which gets the starter motor working fine, have set the Off-Run-Off switch to Run but can't get any power to any of the ignition wiring. Are there any fuses in...

I have an opportunity to purchase a low hour 2014 5055e cab tractor. The issue is it has been sitting for over a year and the wiring harness has been chewed by mice and the owner was able to get a guy to get it to start but no other functions. A local Jd store came out and said it was the wiring...

Does anybody have a wiring diagram for the 620i gator. Ex-JD tech disassembled the fuse block after it wouldn't start after replacing faulty fuel pump

I just purchased a 2004 Deere 4410 loader &backhoe with 580hrs. I was tearing it down to find the flywheel sensor. A lot of wasted tear down since it was in plain sight but the sensor was total missing alltogether so didn't notice at firt. Good news is , found a big mouse nest in the gap...

Found online from a combination of previous diagrams so not sure how accurate this is but its a start: Going to use this as a base to create a diagram for my PT1460. By Coxontools:

Just bought a sickle bar attachment for my PT1460. Need to tame the brush coming in from the sides of my driveway. The attachment comes with a 12V electric switch that operates a hydraulic valve that diverts the hydraulic flow from the sickle bar cutter motor to the lifting cylinder. This way...

Hi, folks, A question about the above. There is a stray wire with no connector near the starter solenoid. Black, frayed, and possibly the reason for my no start issue. Can anyone provide a visual for where this wire should go? Schematics are vague. Thanks!

Kubota M59, unknown year, ~2600 hours. I've had it about 10 months, have close to $40K into it including major service, new brakes, and completely rebuilt loader and loader hydraulics. I just point this out to say I've been operating with an open checkbook to get this puppy sorted, but I'm...

I'm trying to find a good place to tap switched power from. I pulled off the "dash" and noticed that there are 2 connectors that are not connected. (both have orange with silver bands wires) Also I've always wondered what the 2 wires near ROPES left rear is for? (If I short them it starts the...

Where can I get a wiring diagram for this tractor

Has anyone else had issues with their Farmall A series quitting, not running? I actually had a Farmall 55A that had so many wiring issues that I finally traded it in on a Farmall 60A. I just thought i had a lemon, but not sure now. This 60A is now 5 years old ( about 600 hours) and last year it...

Hello. I wanted to reach out to see if anyone has a Readable Wiring Diagram for the 4110 New Sheet Metal tractor. A couple of years ago I purchased a digitized service manual which includes the wiring diagram in the service manual but it is not readable. Does anyone have a readable wiring...

Help MY MASSEY FERGUSON 50D INDUSTRIAL TLB CAUGHT FIRE BURNT THE WIRING HARNESS UP FRIED. I WOULD LIKE TO KNOW IF I COULD GET A COMPLETE ONE SOMEPLACE. THANKS

My tractor does not have a ignition key. It only has a start switch. My problem is how to wire voltmeter in so it will not be on all the time?

I have a YT235C burned lots Looking for wiring, harness, and a lot of other parts Open to find someone with a junk 235 bad engine engine transmission I could buy for parts, or someone with spare parts Hal Halblakely2k@yahoo.com

Hello everyone. I’m in the early planning stages of wiring a new home and want to make sure I do it right the first time. My main priorities are future-proofing energy efficiency and smart home integration. I’m considering a mix of Cat6 for networking, dedicated circuits for high-power...

So, I'm on my 3rd Branson (4220, 5220c and 5520c) and I had one little mouse burrow in behind the firewall and I cannot believe the damage it did. Strangely, it not only chewed through the jacketing on the wires, but also the copper as well. The tractor is usually stored indoors, but I stored...

Needing an engine wiring harness for YT 235 Hal Woodville Tx 75979 , 916-7479818

Need instructions on wiring ignition diagram

I recently purchased a 2006 Jinma 284 with the old rectangular instrument cluster. The tach does not work and other gauges work intermittently. I am interested in purchasing and installing a new instrument cluster and wondered if anyone had done this and if they would share the wiring...

I purchased the tractor recently and I noticed the alternator is not putting out any volts. I have a feeling it might wired up wrong. There are for terminal N, F, A, E . I am not sure if the E terminal is for a ground or something else. I appreciate any info some might have. Thanks

I have a 2001 massey ferguson 471. When I turn the key on the gauges don't always come on. When thay don't come on you don't hear the fuel pump come on. Any help

Hello, I am having issue with shut off solenoid on 325 Bobcat. Its not engaging and wiring is showing 5.5v when ex is off and 4.5v when it is on. which is really odd. I am guessing wires split somewhere? does anyone how electrical scheme for this part of it so I can try and trace it ? Also...

Does anyone have a wiring diagram for a Mahindra Emax 22l. My tach, hour gauge, and fuel gauge have stopped working.

Looking to help help a neighbor with a cold engine starting problem on a TC34DA. All he has told me so far is that it is electrical and he thinks it is something to do with the glow plugs. He has owned it since new and & the battery is good. I am hoping to find a wiring diagram before I jump...

I have an issue with power to the gauge cluster. Sometimes with the key in the Run position it will light up and work normal but most of the time now it all just flashes until i turn on the head lights then it works fine until its turned off. Ive checked grounds and fuses and removed the lower...

This question has probably been asked before, so I apologize in advance for any redundancy. I recently sold my old tractor and now have a new 2024 YT359C. I’ve installed the radio and some other accessories, and I’m considering adding a camera at the back and one at the front for loader work...

I've run into an oddball issue with the brakes on one of our trailers. Three of our trailers have electric brakes, a landscape trailer, a car hauler and a dump trailer. The same tow vehicle used on all, a 2020 RAM with factory trailer brake controller. Everything is fine with car hauler &...

I have a T474 but assuming the dash display is the same on all cab models. The dash has a parking brake light but mine is not hooked up to the parking brake switch. I see several wires missing from the plug. Does anyone have the pin out of the plug? Or know of a source for replacement pins...

Hello to all, You guys helped me source this part sometime ago. thank you. But, just got this note after placing the order. Anyone know if there's another route to go to get my trailer wiring harness? Information below on what it is, and I need the one that includes the reverse back up...

Hi, I have a Massey ferguson 135, the wires to the reR have been cut and taped up to not be used. Im trying to get the rear lights working again and have discovered the wire that that shows is live when the light switch is switched on and another wire that is constantly live. With the wire that...

I'm putting an electric winch on the front of my SVL75-2. It's a Holmes (Ramsey) winch from a tow truck. My question is whether there is an easy way to get the 12V power up front, other than just hooking into the battery terminals and running heavy gauge wire.

I'm replacing the dynamo on my B7800 after the bearing locked up and much squealing and smoke was released (belt). I have the new dynamo but have a very simple question. The two wires coming from the dynamo are the same sky-blue color and have the same bullet-type connectors as do the wires on...

Have an issue with my WR Long 4n1 bucket where the solenoid seem energized all the time. Pulling the fuse to it solved some sudden weird hydraulic control issues. Wondering and hoping it is just the switch or maybe a short hidden from view. Since it is too dark for me to work on it now and...

I will be putting an electric mulch kit on a John Deere x370. I was told by a technician that the wiring from the control motor on the deck can.get snagged on heavy leaves or stick and pull the wiring out. Anyone have comments on this? John

I have a 2021 DR Field and Brush Mower Pro Max52T. I pulled the wires off of the push/pull TPDT switch. The wire colors are red, orange and 2 whites. The switch itself has 8 pins, 2 rolls of 3 and 1 roll of 2. I need assistance on what wires go to which pins on the switch. Thanks

Unlike the GC2300 I bought previously, my GC1725 manual does not contain the wiring diagram. Is this part of "we don't want the users to work on our products program" or is it "we can make a few more bucks from documentation program". I am in the process of adding some electrical options and...

I need some input on horn wiring for 2013 Kioti DK45 se. Replaced the horn with a universal automobile horn, but it just keeps blowing the fuse when switch is pushed. I had to replaced the plastic connectors with individual female terminals on both the horn and diode wires. Diode tested...

Hey everybody, My JD X749 w/ Yanmar engine is giving me fits. The starter has been finicky for about a year being reluctant to turn over. It seemed if I finessed the key as I was tuning the key it would finally engage. Assuming it was the switch I changed it out without success, and continued...

Hi , I am wondering if anyone has run into this situation before on a 90 series. My alternator light came on my dash so I pulled it apart and found the Voltage regulator out of limits. So I replaced it and I did do all the checks on the stator, Rotor and rectifier bridge and all passed. So I was...

I'm hoping someone out there may have a book or CD of the wiring diagrams. Primarily interested in the three wires on the alternator. It has three posts. One large one is battery positive output, one small one I believe might be the tach output signal. The third post is slightly smaller than the...

I am stumped on an electrical problem with a Craftsman T900 lawn tractor. Model number 247.203791. It is made by MTD and the companion MTD number is 13AP79XT099. DOM is 2015. I have searched on line and have not come up with anything helpful. If anyone has a PDF and can share it, I would...

Some one (i suspect a pack rat) chewed up some wires behind the dashboard, and now my fuel gauge and temperature gauge no longer work. But I don't know where to find the part. I tried AGCO parts, but they don't even list my tractor! I can't be the only one with this problem. Has anyone got...

Does anyone have a copy or can send me a copy of the Key cylinder diagram on the tractor listed above, TIA, ken kenben41@hotmail.com

I am looking for a DK35(40) Electrical system wiring Diagram. My Workshop manual is apparently for an older DK35 and the wiring diagram does not contain info for the Tach/hr meter (which is mag style not cable drive.) There is also no indication of the FFT Assy (Display unit). Any Help or...

I am going to wire some auxiliary lights, and solenoid driven diverter valves. The wiring will be exposed to sun and weather. Is SJOOTW, or SOOTW a suitable wire? Or do you have better recommendations? And on wire sizing: How do you size wiring for LED lights? I sized wire for the tiny...

Where does white wire connect to alternator? Alternator has 4 wires red, blue white and yellow. Thanks

New guy here with a new MF 1835e. As with most new 'toys' I acquire, some modifications/upgrades are needed. In my case, and for now, the upgrade is adding a rear work/flood light. I have the light(s) mounted on the inside of the lower portion of the ROPS. The question is, where to get 12v...

Question, what do you guys think of aftermarket wiring harnesses for a Ford 4500. Steiner wants $500 aftermarket is 90 I’m tempted opinions anyone anyone. TIA.

I just picked up my L3560 Grand L cab unit yesterday and it has the speakers and the blank cover over the hole for the stereo. I would like to add a Pioneer head unit to it, and the question is what do I need to buy besides just the head unit? I assume that I need a wire harness kit to tie into...

Need a little assistance finding Temperature Sensor and Oil Sending unit and getting them wired back up. Several years ago parked my Kubota M4800 in a 3 wall dirt floor garage and rats chewed on the heart of the wiring harness in the dash leaving lots of bare copper exposed. At that time the...