snowblower

Purchased in 2012. Not sure of year of manufacture or hours.. Fully functional. My F2400 comitted suicide shortly after turning over 11000 hours. RIP.

I recently discovered the existence of the Bercomac SSQA snowblower . I am not sure about the durability of it. Let me know if you have seen these. I'd like to hear what others have experienced. At the moment, it appears to me as an expensive gamble. It may be one of those you either love it or...

I am considering the CX2510 with a front mount snowblower. The dealer spec'd the SB54 snowblower. I have not been able to find videos of the install process for this combination. The videos that I did find for Kioti front mount snowblowers showed a large sub frame that gets attached to the...

Hey everyone I have the snowblower listed above and I need to replace the shear plate. Does anyone have any experience with this job? Any videos available out there. Thanks

I am considering a JD 2032 and need a front mount snowblower. I did a quick measurement on the width of the rear tires (R4 I think) and thought that the width was in the 58" range. But I've seen some videos of 54" blowers on the 2032 and the rear tires seem to fit in the path that the blower...

I have an S130 Bobcat. I want to get a snowblower for it but not sure I have the right connections. I know you need to determine if it’s low flow or high flow. And the snowblowers I’ve looked at have and electrical connection and my Bobcat does not. See attached photo. Do I have 3 hydraulic...

I have 72" Bercomac, model #700969-1-33v with the 33hp B&S mounted on a tractor. B&S engine is running, second stage is spinning augers are not. The shaft from the second stage to the gearbox that drives the augers is spinning. I can spin the augers freely. Both move together. All three shear...

Greetings, I have a DX24E and I'm hunting for a snowblower for it. From what I gather the supported one is BSX150 and that the new holland equivalent is a 50cs. Neither of those I can find. However, I am able to get a 51cs. Is there any foreseeable issues with this blower and my tractor? Thank...

Wondered if anyone would share thoughts on running a pto snowblower on my 2040. Who has done it? Is the old girl geared slow enough? How many augers, width etc... Any input appreciated. Maple season almost upon us and I thought I would pick one up to clear paths in the fields to my lines...

Does anyone know of a MF dealer who has a hydraulic chute rotator for my 2360 snowblower? My dealer tells me that MF switched sub-manufacturers and now sells an updated blower that's completely different. I've tried contacting the Canadian manufacturer of this blower but no response (they do not...

Have the quick-hitch and blower, along with the manual for the blower. Have found some diagrams (thank you Messick's and Coleman Equipment) that show the arrangement of the TG2739A quick hitch and can guess as to how it has to go under the tractor. There do not seem to be any manuals or diagrams...

HI. All. I attempted to mount my Front Snowblower today (Kubota B2782B) on my B3000. This particular model uses, what is called, a "Sled" undercarriage mount. It uses a long drive shaft connected to the Mid-PTO and a much shorter one from the sled to the Blower itself. It has a rectangular...

HI All. I haven't had to use my Front Mounted Snowblower (B2782B on a B3000) for a couple of years. But they are calling for 4-11" of snow tonight/tomorrow and plan to mount the snowthrower to use. I can't find my manual right now and wanted to know what the working RPM should be when using...

I got a new tractor this year, TYM 4820, and finally got my old Ber-Vac front mount blower hooked up to it. Blowing snow with a heated cab is a game changer.

Looking at a 59 Snowblower off of a 955 Deere but wondering if it will fit my 870

One of the auger shear bolts on my BX2816 snowblower broke. That side of auger spins freely, but it looks like the bolt off broke cleanly inside of the inner axel, if that's possible and I can't push it out to replace it. Any suggestions? Thanks.

I couldn't bring myself to pay $550 for the hydraulic deflector from the dealer last year when I purchased the blower. After one winter clearing the driveway at our place, that seems to always be windy, I had had enough of that. Bought a 2 inch bore 6 inch stroke hydraulic cylinder from tractor...

Hi, After a few seasons with our geared tractor I think I'd really like HST fully variable speed. To be able to inch into the bigger drifts, whizz along quicker when it's shallower. At the moment I'm stuck with a fixed 0.89mph. Also to be able back into the drift with blower raised, then shuttle...

Here’s my mod for my BX2750D for use on a new property with gravel driveway. 3/4” rebar was welded onto circular plates and heated with a torch to form a circle. 1” square tubing slides in receivers made of 1 1/2 angle iron welded together. Three 1/4” holes 1/2” apart allow setting them 3/4”...

It’s getting to be that time of year again… I bought a 72 inch Woodmaxx snowblower last year to use behind a NH Boomer 35. We only got a couple feet of snow so it only got used a couple times. I’m in northern Wisconsin so we typically get a lot more. My drive is old asphalt, and the parking...

What front mounted snowblower would work for a new RK24 subcompact tractor? Would also need tractor mounts for this snowblower.

The wear ring is all beat up on my snowblower chute...I'm not even sure what it is officially called and I haven't been able to find it online yet...it looked like 1/4 inch thick poly c-channel? I am hoping someone can point me in the right direction..lol..at least snowblowing season is over now...

I just pick up a Gravely snowblower that go's on the front of there tractors. The S/N is 05117661 this is a 4" wide snowblower. I would like to put this on the front of my 4-wheel drive mini tractor. I will be putting on the blower it's on 20hp motor to run it. My question is how fast do the...

I just wanted to say my Yanmar SB60R snowblower, attached to my Yanmar 425 performed like a champ this winter. I live in Montana and we had a light winter compaired to most years but when it snowed. it was in feet and usually multiple. The blizzard of January 17, 2024 I plowed 4 1/2 miles, 3...

Hello All, I am hoping I can get some feedback and guidance here as I just purchased a 2023 Kubota GR2120 with 54" deck and front snowblower. I still have to wait about two weeks until I receive everything but am wondering: How high off the ground in Inches does the front snowblower raise on...

Sorry if this is a dumb question but I can't for the life of me find a real yes/no answer. I'm looking at a used 2019 L4060 with a mid-mount PTO. I asked the owner if the mid-mount PTO meant that it could run a front-mounted snowblower and he said yes, yet all I can find for L4060 snowblowers...

Hello All, Looking for a Fan/Impeller for an Allied YC6010 Snowblower. The original fan is a 3-blade, but they have since replaced it with a 4-blade fan. The part number for the new 4-Blade Fan is 907118, but I can't find one anywhere! I have called every Farm King Dealer within 500 miles...

Hi folks, my husband and I bought 25 acres in a snowbelt in Nova Scotia, Canada. Our driveway is gravel, a bit of a switchback up the mountain, 1000ft long and climbs about 100-120ft in elevation. I'll be doing all the snow removal, because I work from home and my husband leaves the house at 4...

I recently purchased a B7200HST. I need a snow blower attachment. I have read the that correct model is the B2551. Can anyone confirm that and if so, where do I get one! :) Are there other models that would fit? Do you guys prefer the front mounted over the 3 point rear mounted? This is my...

I had a few questions about the hydraulic chute rotator for the 2360 snowblower. I can’t seem to find a part # for the kit anywheres. I currently have the electric rotator but I am sick of the speed and how it freezes up every time I am out. Does anyone know if it is a simple bolt on kit? Or is...

my McKee econoplow snow blower needs some love. the chain tensioning is done via a flat belt pully and a bolt in a slot for adjustment, very simple and very worn out. should I find another flat belt pulley or replace with an idler sprocket? any advantage or disadvantage to either one? its a...

Good afternoon all, I have 2006 toolcat and a 2014 SB200 snowblower. I am able to get the main augaur to turn, but am unable to get the chute to move left or right, not adjust the pitch. Any quick recommendations? Thanks in advance!

Call me crazy but it seems like my B2782B blower on a B2650 tractor only wants to lift up when the tractor is at low rpm. It will go down at high rpm, but not lift up. Is this normal behavior? Fluid is full, all other parts of the tractor are working fine. Checked connections too. My normal...

Hola - title says it all.

Hi, My JD setup is making a racket... some due to loose sprocket/chain - replaced the sprocket and chain/tightened... Some of the noise might still be that I was not paying attention to aligning yokes.... got that from another thread.... but I've also found the PTO shaft is rubbing on the tie...