rpm

We are trying to run a John Deere hay conditioner behind my 4710 tractor. We selected 1000 rpm on the lever, correct speed for the implement. The PTO engages , then disengages after about 10 seconds and the warning triangle lights on the instrument cluster. It works correctly when set for 540...

Hey guys, According to this video and John Deer, we should not be using high rpm's on our tractors IF it is not needed. Supposedly people saying it is better for the emissions controls or DOC filters etc. have it backwards. Watch part or all of this video, check out what Deer says and let me...

KIOTI Ck2610 - doing dirt work and lifting ibc totes of wood, what type of RPMs should I be looking at?

I purchased a rk37 used with 300 hours rpm will not go higher then 2100 it bougs down under load I clened all fuel lines and replaced with new filters does anyone else have this problem

Skimming through the manuals for my GC2400 and the 60" mower deck, nothing is stated regarding at what engine RPM is recommended when engaging the lower PTO. Once engaged, I do increase the RPM to the "green" zone when cutting grass. What are your "best practices"?

Hey everyone I got a new DK4520 8x8 shuttle today and I'm a bit curious what everyone's advice is on operating rpm's to minimize the regen process from occurring. The dealer told me to keep it above 1700rpm at all times and the higher the better while low RPMs can be attributed to clogging the...

I’m hoping someone can help. This ESC light has been flashing. I have tried turning the ESC on or off. The cruise control does work but the light doesn’t change. Then I noticed the digital display of RPMs is stuck at 1,000 RPMs. I can throttle up over 2500 RPMs no problem. Regen seems to be...

I am having an issue getting my PTO to shift into gear. In fact I broke the arm (PTO Rod) that goes between the shift lever and the actuator trying to get it to shift. After the arm broke the shift lever moves up & down freely, so it has to do with the PTO Shift Lever Shaft or something...

Hello, I am having a throttle problem with my Belarus 250AS. The hand and foot throttle controls do not change the engine RPM. The tractor will start, but it's a 'runaway'. I have to kill it by placing something over the intake and it will slowly starve the engine of air and it will then shut...

I just pick up a Gravely snowblower that go's on the front of there tractors. The S/N is 05117661 this is a 4" wide snowblower. I would like to put this on the front of my 4-wheel drive mini tractor. I will be putting on the blower it's on 20hp motor to run it. My question is how fast do the...

Hi there, Anybody replaced the RPM sender ? When first startup my 3520H sticks on really low RPM no matter what throttle is set at. After several minutes, like during warmup, the RPM starts reading normal. Hmmmm I figured it's likely a sender unit starting to go. 2014 3520H model. ~Regards

From time to time, my tractor has been having issues of reaching rated PTO RPM, which I’ll post about separately. While looking into this, I found errors in the Kioti CK2610/3510/4010 owner’s manual. My owner’s manual is dated JUL 2018, so perhaps this has been corrected in later versions. My...

I have a Boomer 35 with 500 hours on it. It suddenly dropped down to a constant 1350 RPM and did not respond to any throttle movement and then, just as i got back to the house, dropped down to the 900 RPM idle and stayed there. Later it started right up on several tries and then jumped back up...

I have a problem with my tractor mower. When the blade are lowered, revs begin to drop and the mower shuts off. The traktor has 2 blades. The engine is tecumseh, 12hp. The carburetor is cleaned and the spark plug is sparking. If anyone knows anything about the problem, please write.

I have a 2019 Kioti DK 4710 SE that has started acting up just a month or two out of warranty. This actually started about two months ago, but I haven't had time to deal with it yet. The CEL is coming on even after I disconnected the battery or ECU for a few minutes. The light stays off until I...

Hi everyone, I need help diagnosing my issues. My tractor idles for a while before dying. However, when I have my RPMs up, like at 2500 RPM, the tractor runs fine and continues working. During idle, when using the bucket, the bucket drains a large chunk of my RPM. What could possibly be the...

I've dug through the forums here and even read some scholarly articles on the subject but I still don't understand how revs affect the performance of the HST when using hydraulic implements like a loader. I can feel the difference it makes in pulling, cutting and ground engaging implements but...