kubota b7610

Could anyone tell me where the hydraulic relief valve is located on a B7610? I expected it to be on the right side near the power beyond but I'm not seeing it. Actually I looked under it on both sides and nothing is jumping out at me. Any help is appreciated.

Hello all! I am sort of new to the forum. I read it regularly but rarely post. I bought a used Kubota B7610 HST. It's been a great little tractor and I would like to replace/fix a few minor issues it has. It needs the fuel level float switch. Is there a good place that sells aftermarket parts...

Kubota b7610 . PTO will not engage with the belly mower. Engaged yesterday then quit again . Help !!!

My B7610 was working great last week and while I was rinsing the radiator screen off, the tractor cut off. Many attempts to start it failed. Today I had a chance to look at it and I discovered that a 30 amp fuse marked “solenoid“ was blown. Thinking this was the answer, I put a new 30 amp fuse...

After seeing a small leak inside of frame I eliminated usual spots ( thermostat, cap, radiator.) must be the water pump. I can't really see a leak but it must be something to do with the pump. it is hidden behind the lower hose. So I have new Kubota hoses and water pump. Now the next nice day I...

I have a bad OPC controller I'm waiting on a new one to come in but in the mean time I need to move it, so I bypass the start by jumping the black/white and black/yellow and it turns over but no fuel does anyone know which wires to jump so it gets fuel looking for wire color. Thanks

Good Morning all. My B7610 was running great. I parked it in the yard and went back to start it the next morning and I am getting nothing. The 3 lights on the dash come on. I have did the usual play with the PTO handle, pushed on seat safety switches and push in forward and backwards gas...

Hello, I currently have a B7610 tractor. I have a line on a B2781 blower with a B2714B under carriage ( mount). I was told I need a b2733 Mount for my tractor. My question is, can the B2714B Mount be retrofitted to my tractor or do I need to purchase the Mount separately? Any and all information...

I just got my B7610 back from my son. He's normally pretty good on checking fluids etc. But today I went to use the 3 point and accidentally bumped it into "raise" position, where it sat for a minute or so. It dumped like what looked like a lot of fluid, probably a half pint at least. Yet when...

I have a 7610 and a mower deck for it. When I installed the deck with the rear controls lift the bracket hits on the reverse. Has anyone else had this happen or know of part I’m missing?

My wife was using our B7610 with our brush cutter when she found that the tractor would not move forward or backward and none of the hydraulics would work. I can easily start the engine but can't lower or raise the front loader, lift the brush cutter or get any movement either forward or...

Have a couple issues with my B7610. The float is no longer working on the loader so wondering where I start to see if I can fix or adjust that. The loader has full motion otherwise it just seems to keep pushing down instead of floating when I try the float position now. Also periodically I...

I've started looking for a MMM for my machine just as a backup for our mowing crews. We have some commercial properties that have big open areas where a tractor manuverability won't be a hindrance compared to ztrs. What models will direct fit onto my machine? Thanks

I have a 2004 Kubota B7510 with a FIXED ROPS. I want to trade it for a FOLDING ROPS. We can work out logistics in text or call. Curtis

Hi- first post. Looking at a used 07 B7610 but trying to figure out how it fits in size wise with the newer BX and B tractors. It痴 a 5 hour drive to find out its to small. Basically I need it to move/blow snow, firewood, and maintain food plots. Nothing major but we get 250 of snow in the UP...

Hello Mechanics, (not me), I want to change the hydraulic oil in my B7610. While trying to figure out where all the drain plugs are (not in the book), I see there are two filters. Are they both part of the transmission system? Should I change them both at once? What else do I need to know? I...

I've searched high and low but can't seem to find any answers. I currently own a B7610. I have a chance to pick up a front mount blower from a friend. It's a B2782a (63") with a B2792 or B2793 frame off a B3200. Will this blower fit my unit? Thanks in advance guys, John

My operator went to start the tractor last storm and nothing. Usually it means the pto lever isn't perfectly in neutral. That was fine. The starter does work when the posts are jumped. When turning the key, on occasion, you can hear a click from inside the steering column, but it doesn't make a...

Hi, So I'm hoping someone can help me out. I recently bought a used b7510 TLB and have decided I need to add an alternator for work lights. I purchased a pdf version of the service manual and unfortunately it contains everything but pages 9-M1 and 9-M2 which would be the wiring diagrams...

B7610 with 400 hrs.It usually starts pretty easy when cold.You can run it for 5 min. or more and cut it off.It will have to go through a complete cool down before it will restart.Important ---When it does start its a split second after you release the key.Hardly ever will start while...

Can anyone suggest what a fair market value is for this tractor with about 100 hours on it? Good condition, always garaged, one small dent on fender. Thanks! Mike

I have a friend who is looking for a TLB. There is a B7610 for sale with a Curtis cab and only 148 hours. Looks to be in very nice shape. Seller is asking 17,500. Three questions: Is the price too high? Is he better off with a newer BX series TLB? How does the BX series compare with the...

I searched high and low (on the forum) for the correct filters for my HST/Hyd filters. I thought I had it nailed but things did not work out. Kubota Parts shows the two filters to be: hh660-36060 and hh670-37710. NAPA crosses to 1361 and 1551. I purchased the two NAPA Gold filters but they...

I am looking to get pallet forks for my Kubota B7610 with a LA352 loader. The good people over at EA (where I am a very satisfied customer) have recommended the Construction Attachments 42" Compact Pallet Forks (the EA forks will not fit my loader). I have considered going the quick attach...

Got a 2006 B7610 with under 400 hrs.on clock.When cold it starts pretty good after 3-4 sec.on the glow plugs.After you run it awhile it will have to sit a good while before it will start.When you turn off engine you don't hear the click after a few seconds.I can't remember what the click sound...

I have a B7610, PTO is stuck in gear and won't shift into neutral. Any suggestions?

Like the title says, I've got a hitch problem. It will go up but not down. I was having an problem with the hitch not going down when I noticed the lever roll pin was coming out. I pushed it back in but it still nothing. It seems like the neutral/center is where the down position was. I pulled...

I have a b7610hst with around 1000 hrs on it. I started to back it out of the garage and it started moving then it paused for a couple of seconds then it started moving again . Now is where things got bad. It stopped moving again and started making a loud squelling noise out of the bell housing...

Trying to go forward, I'd press the HST pedal, the engine would go down from 2,000 rpm and just about die. Take the foot off the pedal, would resume engine speed. Either forward or reverse. Almost like a lack of fuel or air. Checked both, seemed ok. Figured out my son had flipped the...

Recently I had a thread about using a hay spear on the bucket of my B7610. Lots of good ideas and thoughts from folks. I tested the lift capability of my bucket by strapping a round bale to my bucket. All was just fine. It lifted it up and though a bit tippy, as expected it was fine. Yes...

I have the need to be able to store round bales of hay for my mules. In the past I have easily moved them with my 3PH and hay spear. Now though, I am getting a super deal on some fescue and with the drought that is anticipated for the rest of the summer I am gonna get a WHOLE BUNCH of bales...

I recently bought a used B7610 with about 300 hours. It's equipped with a loader and MMM. The hydrostat will occasionally "upshift", without moving the pedal, as though it was an automatic transmission selecting the next higher gear. The ground speed will increase slightly, maybe 5%. I also have...

What model mowers fit the belly of the B7610 Tractor?:rolleyes:

I sold the B7610 over the weekend. It's kind of bittersweet since I sold my house with a 3 acre lot. I'm going to miss it a lot. I've always enjoyed all the years on here sharing information and trying to help one another out. Thanks to everyone who helped me out over the years with different...

My cluch will not do anything, machine keeps going in gear when you push in cluch.....pto keeps spinning....yet I can change it from low to high no problem. Any suggestions on how to adjust

Hi all, My neighbor is selling his Kubota B7610, 4x4, HST, with 226 hours for 15K. The going rate for comparable machines in my area seems to be around 9k-9.5K with FEL. The extra expense is for all the stuff that goes with it. I has a FEL, 48" brush cutter, box scraper, chipper, rototiller...

I'm considering buying a used B7610 to replace my BX2230. The B7610 has a loader, but no mid mount deck. Can someone tell me the 60" mower model number required for this tractor? The BX and B decks all look pretty similar, and there's one on our local CL for a BX. But I'm pretty sure it...

never mind

The B7610 FEL has a lift capacity of about 700 lbs. I'm wanting to get a Piranha for it AND pallet forks. Bxpanded doesn't sell forks to fit for the B7610. I kind of like the concept of the "hanging" pallet forks. Is there another mfg that makes that that type of fork?

Son lives ~ 4 miles away and it looks like we will be sharing my B7610 frequently. He's got a little Toyota SUV w/ a 2" receiver and I expect the tow rating is 5K lbs. Will find out. He's wanting a small trailer for himself, primarily for hauling stuff from the lumber yard, camping trip...

I have the rear tires filled with salt water and I picked up a nail in one of them due to the roofing crew at my house I now have a flat & I have salt water all over my garage floor UGH ! ! ! My options now are as follows: Swap out the tube & refill the one tire, drain out the other tire &...

I have an intermittent problem with my B7610. I warm up the glow plugs upon starting and turn the key and it starts and shuts off right away. Other times it starts and stays running. When it doesn't stay running, I bang on the top of the instrument panel with my hand and it starts and runs. What...

So I finally broke down and got a front blower to give my neck a break from the PTO blower (arthritis setting in). Other member here get the credit for how to do it. I thought others might like some detail on the process. Dorman 742 297 New Window Motor | eBay (wiper motor $41.64) Heavy Duty 4...

My Kubota B7610 has been intermittently stalling for 5 years. Once every few months it would slow down to the point of almost stalling. Full tank or empty tank didn't matter. Over the last 5 years I temporarily jumper-ed out all the safety switches to no avail. I changed the fuel filter...

I use a belly mower on my B7610HST. Recently it seems to chatter or cause uneven loads on engine. Is there adjustment I need to make on a drive clutch or something for the mower deck? The model of the deck is in my signature.

Hi I did my first 300 hr service on my B7610 the other day and I had to drain the front transmission as well as the rear. There is only 1 fill I can see near the rear of the seat. I see that the two assemblies are connected with pipes so is the one fill point the only location required to add...

Looking for an opinion on pricing. I bought the 7610 new from Cavalier in VA about 10 years ago, with FEL and Woods 48" box blade. I purchased a Land Pride 72" rake a few years ago locally (Southern NH). Selling all as a package. All equipment has been stored indoors. Currently 212 Hours.

never mind bought a 5'

I believe the B2620 replaced the B7610. Are the bolt patterns for the rims the same between the two models? I'm looking for some used rims to try out some different tires.

What is the recommended operating RPM for a B7610?

I have asked this several years ago, but I am just now able to make a purchase. The responses I got back then was with prices before the steel price increase and some of the responses I received were websites listed that do not exist any longer, and even I can't find my original post. :) I...

My B7610 tractor is slow starting and runs for a few minutes and stops. I then must wait a while before starting again. I have changed the fuel filter, air filter use fresh diesel fuel. Any help would be appreciated. The Kubota dealer is about an hour away and very expensive. Richard Ashby, Ma.

My new to me B7610 with less than 500 well maintained hours is quite the machine for me. Does everything I have needed it to do really well.........Moved 4 dump loads of crushed chert ore for fill, 5 loads of crusher run and spread it, maintains with blade 1/2 mile of gravel, bush hog and...

I mistakenly posted this in the General forum. Hope you don't mind re-posting here. My kubota 7610 doesn't have very many hours on it (~200), and I'm having a problem with the 3 point lift losing pressure. It can lift the rotary mower and other implement w/o a problem, but they slowly start...

My kubota 7610 doesn't have very many hours on it (~200), and I'm having a problem with the 3 point lift losing pressure. It can lift the rotary mower and other implement w/o a problem, but they slowly start dropping. Even w/o anything attached to the 3 point within a day or 2, it will have...

I know this must be fairly simple but it's a problem to me. I have a B7610 that I acquired a few months ago with 426 hours on it. Everything works and it is really a strong machine. Anyway, I noticed the other day that the turn signals flash opposite what they should. When you turn the...

For my B7610, I have available: FEL, rear blade that the angle is adjustable, Box for adding weight to rear, and box blade. My drive is a 1/2 mile partly gravel and part asphalt hill with 20 degree slope going up the hill and back down to the other side. In past winters I had a 2 wheel drive...

Question on a new to me B7610. The three point hitch lowers rapidly. The manual states that the lowering speed can be adjusted with the knob centrally located on the operators platform by my feet. Well, it seems to be frozen and will not turn either way. The manual shows the knob with a half...

Getting some crunching sounds out of my rear axle both on the left and right side of the tractor...Sounds like it is coming from the axle....Is this a pretty uncommon sound? I notice that when the rear of the tracotor is underweight, i.e. implement lifted off ground and more weight on the...

Hi All: I am new to tractors but just pulled the trigger on a used B7610. I am going thru the shakedown to see where I stand and have two observations/questions: 1) The way I read the instruction manual, the glow plug light should come on when I turn the key one notch, regardless of ambient...

It's been a while since I've had the B4672A 3pt backhoe off my B7610. When resetting the Hydraulic Control Lever adjustable stops I can't remember if the hydraulic lever is supposed to auto return to center when using the 1/4 inch stops or not. Any help appreciated...

With my new to me B7610 the PO, previous owner, changed the hydro fluid just before I picked it up so I dont know how much he put in........The question is: When does one check the fluid at the dipstick under the seat......before starting, while running, or just after stop the engine...

My dad bought a B7610 and has a little trouble getting on and off his tractor. I can make a step for it and it's looking like I'm going to have to. I was just wondering if their is a factory step made for the Kubota B7610 that he can just order

On my new to me B7610 am having to work in some pretty slippery stuff and am trying to get the diff lock for the rear to stay engaged without having to keep my left heel pushing down. The darn thing is in a pretty hard place to even get one's heel into and then to have KEEP pushing down is next...

Front axle leaking at pivots. Common problem on here. Does anyone know how to get the pivots apart to replace the seals? Looks like the cover for the bevel gear may need to come off to access a couple snap rings.

I just recently bought this tractor at an auction after finally recieving my manuals in the mail I started to go over tractor today. Well when trying to remove front axle fill plug it was almost impossible to get off finally after putting vise grips on it it came out, but now I can not get it...

On my "new" to me B7610 when I grasp the handle on the fender and the bar across the hood in front of the steering wheel, I feel the handle and fender "move" perhaps a quarter of an inch. It has about that much "play".........Is this common?......I tried tightening the single bolt on the inside...

I have been on here for about six months lurking around what a great site, so much useful information. Well after researching for that time I decided I needed a tractor for the property. Two acres of lawn and 30+acres of woods. I went to the different dealers and looked at all the tractors I...

My wife was moving some dirt and the engine stopped. I've checked all the safety switches, no power at the clutch switch. I'm in need of a wiring diagram.

I have a Kubota B7610 with the Mid Mount Mower and am looking to buy a Woods BH70-X backhoe with the subframe mount. Does anyone know if the mower can still be used (backhoe removed) with the Woods subframe installed?

I was offered 10k for my B7610 ( in excellent condition) towards a new B2620, loader and b65 backhoe. The reason I'm upgrading is because if I want a decent backhoe, I would go with the bh70x Woods. That is close to 10k all said and done. So I figured an additional 4k and I have a new machine...

Afraid I broke something today in the hydrostat. Just put the mower deck back on and went to lower it this morning and it wouldn't come down. Checked the linkage and noticed that one of the brackets on the arms that attach to the back of the deck was stuck. These are the brackets that the arms...

I feel the need for a tiller for my 7610. I've never used anything more than a Toro walk behind so I'd appreciate some advice and council. I have 10 acres with 7 in pasture and 3 in home, yard and barn. All could use a good soil loosening. We have a high clay content that is quite hard. Any...

Disregard. Found my manual.

i am selling my 2006 kubota b7610. the tractor has 250 hours. 60in mid mount mower, and the la352 loader. i also have the following attachments landpride rta 1050 3point tiller, landpride bb 1560 box blade, woods tch4500 3point wood chipper, a 3 point straight blade, and a quick hitch adapter. i...

I've got an '07 B7610 w/ only 300 hrs on it and am wondering what I should expect for the life of the glow plugs and controller. If I need to do the job I'd like to work on it this spring or fall. Last time I fired it up it worked fine. Does anyone have any guesses? I've also have a Sato...

I recently purchased a set of 2-link ladder chains for my B7610 from Tirechains.com. I ordered the set recommended for my 12-16.5 R4 tires and a set of spring tensioners to try (I normally use bungee cords). I go through the normal steps of installing new chains and see theres some slack so I...

Does A b7619 hst TRANSMISSION have fan cooler?If so where is it,I can't find the fan nor have I ever heard it come on? Thanks, tony

This weekend I installed the 2nd best part mod on my B7610 next to my Markham toothbar. I installed an extendable 3-point link arms / telescoping stabilizers kit from TractorSmart. It's all the parts from the B2910 IPL in a easy to install kit. I read the threads below a while back and had...

I've a Kubota B7610 and a Woods BH70X (lovely combo). Mounting instructions require removing all of the 3pt components, top link, lifting arms, etc. I've been doing this, but removing the lift arms and telescopic stabilizer bars is a pain. Today I just had to raise the BH to hook up the...

I had one B6200 ((20 years, 2600 hrs) and presently a B7610 (7yrs, 390 hrs)), and I have never had any fuel issues. I always add Power Service supplement each time I get a fresh five gallon can of fuel. Today, without any load, the 7610 engine began to frequently drop from full rpm to about 900...

I have a B7610 (which is the same basic tractor as the B2410, B7510, B2400, B2100, B1700, B7500, B7410, B7400, etc), and currently use a 5' back blade (too short, need a 6' to cover my tracks with the turfs set wide) for accumulations under 6", and resort to the Woods SB60 blower for anything...

I'm thinking about buying the Kubota hydraulic front blade for my B7610. I already have the 352 Front End Loader, which I believe will provide the valving for the Front Blade. I was wondering if anyone can give me an idea of what they paid for the same unit (and how recently you bought since...

I'm thinking about buying a Kubota B7610. What were it's production years. People have cautioned me not to buy a tractor w/ a short run. Thanks.

Over in the Attachments forum there's a thread about a CHEAP stump puller. http://www.tractorbynet.com/forums/attachments/189043-stump-speech-6.html Basically jake98 took a cylinder, some HD chain, and enough hydraulic line to be able to park his tractor at a relatively safe distance, put it...

I'm retiring to Mississippi. We had been looking for a house with several acres (2 or up) and a little lawn (I thought). It seems that lately SWMBO has only been attracted to houses with several acres of LAWN. and spoken with a voice and facial expression that I married her for. That had NOT...

Hi all, I recently moved and have seriously downsized my land. I have a 2005 B7610 HST with about 70 hours on it, with a Kubota Belly Mower and Woods RB60 Rear Blade. The tractor is in great shape with only a few minor scratches on it. I have had it on Craigslist for a bit and gotten a few...

Did a search, results below. Looking for recommendations on best chains for the buck for my ride to be used in Vermont and Virginia snow and mud in both plus Mississippi. Looks like I only want rear chains for now due to 4wd issues. [H patterns seems advised: But tirechains.com doesn't...

I have a B7610 4X4 HST with the front axle leak. I have read a few posts on this, but has anyone fixed one yet? I don't have a service manual right now. Not sure how it comes apart. Also, when I first start the tractor, everything sounds normal. After about a minute, I start to hear an extra...

Hi, I'm a new member to this forum. I just purchased a 2005 B7610 Kubota tractor. Interested in any recommendations for a suitable snowblower attachment for this tractor. Thanks!

Got my first small problem with 2006 B7610 200 hours.After getting it up temp 30 min or so.Like if my phone rings and I cut the engine off it wont start say after 5 min being off.It has to sit and cool down for 30 or so min.Also I've noticed I don't hear the click sound after you turn engine...

Hello, I am fabricating a DIY backhoe. I want to run it using the existing tractor hydraulics. Knowing nothing about hydraulic systems my question is if it is possible to do? My B7610 has a LA352 loader which is run using a joystick, I do not know anything else about how the hydraulics are...

Hi Folks, Looking at an '04 B7610 with 2xx hours. Includes FEL, Bush Hog (looks like factory) and a box blade. Any suggestions on things I should look for when giving it a once over? I don't have much experience with compact tractors, any suggestions are welcome. Thanks!

Hey guys, Just picked up a backhoe for our 7610, It was a demo, so it was all assembled buy it was previously on a 3400 larger machine.... We wrestled to get the unit on the tractor and I'm not sure we have all the top link and lower frame adjusted properly... Anyone have any pictures of...

Does any body have this problem and if so how did you fix it? I can open the hood with the fuel tank cap on but can't close the hood properly without removing the cap and then replacing after the hood is secured in the locked position.

Can anyone give me the part number(s) and tell me if there is more than one fuel filter?

I've been watching Craigslist for a deck that will work with my B7610 and I understand the only model that will work is the RCK60-24B. I was able to locate one relatively close to my location but I'm not familiar with how this thing needs to mount to the belly of the tractor and/or if it will...

well i bought another Kubota last week: it has 159 hours on it, with a fel: B7610: the 50 hour service had not been done on it, so they went ahead an did that: $10k: i "think" i did ok: the dealer had sold it new, an the person that owned it supposedly bought more land an needed a bigger...

I have a 4 year old B7610 TBL with approx. 200 hours in good condition, backhoe is a Kubota 6' any ideas on what it is worth. Loader has a dent and scratches. Mike

When I needed turfs for my B7100, I was fortunate enough to find a set of unused rear turf tires/wheels that were old stock removed from a a new B7300 that was changed over to ags or R4's. I got them for less than 1/2 what it would have cost to buy the news through the Kubota dealer. As...

The engine on my b7610 will slow way down and then speed back up on it's own. Any hints on what could cause this.

I apologize in advance for being a wiring idiot! I am trying to wire up a work light on B7610. I have located the work light wires under the seat and if I understand previous threads correctly the "Red / Blue" wire is +12V and the Black with the ring end is the ground. I want to wire up a 12V...

Finally got my Kubota setup for plowing this winter. I purchased a 72" manual angle UTV plow setup and welded up a custom hookup for my bucket. I already had holes in the sides of my bucket for the teeth so I was able to use the same holes as attachment points. I also already had the hooks on...

I recently came into possession of a used Kubota 7610 with FEL with only 160 hours on it and have already put it to good use with a new Wallenstein BX42 wood chipper. Which works great by the way. Now I am looking for a 4 - 5 foot brush mower to keep a couple of small fields cleared of grass...

I am looking at a fairly new Land Pride 2660 brush mower to use on my Kubota B7610. As I understand it my Kubota has about 18 hp. at the PTO and I would like to know if that is sufficient to operate the Land Pride 2660 medium grade mower. The literature I find on the net so far says the 2660...

Has anybody had issues with the differential staying locked on their 7610's? Mine seems to be locked full time, the reason I think this is that both wheels seem to spin at the same speed constantly when turning. I thought one should spin and the other slip normally. Anybody have any ideas...

I currently have turf tires on my 7610. I am looking at getting some AGs. The manual says to use 11.2-16 on the rear. I have access to a set of 12.4-16's on rims. Will these work or are they to tall? Same size front tires 7-12 as the manual calls for. I think the 12.4-16's are on the 7800...

Some pics this weekend at the lake: Dropbox - Photos - Secure backup, sync and sharing made easy.

Looking to purchase a 3pt log splitter for my 7610. My question is do I need to get rear remote valves installed or can I run hoses from the loader valves the splitter? If it would work, would I need to use the loader stick to operate the rear remotes? 2nd question. Are rear remote valves...

Here is the hydraulic top link: I also now have the B2910 type telescoping stabilizers (which were not on yet when I took these pictures). If you don't home remotes yet, here are some pictures that might help: Hydraulic block location (FEL will be connected here): The connection toward...

Being able to tap into the experience of many of you on tbn has offered ideas and solutions that I did not realize existed. While it has certainly helped lighten my wallet, it has also saved me by helping make the right choice the first time. So a genuine thanks! I have ordered the 2910...

Wondering what to expect. This'll be with FEL or ballast on front. tried a search but ....

I have a 50" 3pt snow blower that I bought with my B7100HST, which is rated for 12HP at the PTO. I now have a B7610, which is rated for 18HP at the PTO (24HP at the engine). My question is, is it worth upgrading to a 60" snow blower if I find a good deal on one, or would I be best off with...

Hey guys, every once in a while the B7610 wont start. It wont turn over. I can start it by turning the key on and then shorting the terminals on the starter. Other times it starts fine. Is there some electrical component between the key and the starter that would be doing this? I would...

I've only had my B7610 for a short time, but today, I noticed that I think the hour meter (which is in the tach) is based on RPM (which makes sense for maintenance), instead of clock time. I came from a B7100, which had no tach, so the hour meter was a basic hobbs-styled that just measured...

Howdy all, This is my first post but I've been lurking for several weeks learning as much as possible. I've tried to answer this question by searching the forums, but haven't come up with anything, so here goes. I recently bought a 2005 Kubota B7610 and would like to add a box blade but am...

Anyone have a copy they would sell? I could use an owners manual also. I know about the online locations to buy from, but thought I would post here and try to buy used at a discount first. Great Site, Thanks!

Anyone know a part number for this. I searched Tractorsmart.com for "tach cable" but came up empty handed. Mine broke 3" or so up from where it mounts on the engine. Near the clip that holds it. ACtually, I think the clip is what caused it to break. Anyhow, anybody bot any info? I could go see...

I just tried to mount the RS1303 on my B7610, and think I might need longer arms. My hydraulic top link doesn't go short enough to get it at the right angle, and it barely gets off the ground to move it. Plus, I can't get my slip clutch on and use the PTO shaft that came with it, as there...

I've seen here that the B3200 FEL quick attach can be used on the B2920/B2620 (and B2320?). I'm assuming that the B2920 and B2620 are using the LA354 FEL. I have the LA352 FEL on my B7610, and was going to pay to have a QA of the same design made for it, but was wondering if the B3200 QA...

I just got a B7610 that has R4's. The rears are 12-16.5 (approx 33" outside dia.), and the fronts are 23x8.00x10 (aren't tire sizes confusing). I might be able to buy a set of 33x12x15 turf tires on wheels (same outside dia. as my R4's), but was wondering what size turfs come from the factor...

I just purchased a B7610. The rear wheels and hubs are on "inside-out." By this, I mean the lugs are facing inward. What is the reason for doing this? It doesn't appear to give it a wider tread, as the tires are only about an inch from the fendors? Thanks, Jay

I just purchased a B7610 w/ 127 hours on it. It is probable that the 50 hour service was never done. I'm definitely going to change the engine oil. Does the transmission oil get changed at 50, or 200 (like the normal change interval). Also, I need an owner's manual for the B7610...

I am adding rear remotes to my newly-purchased B7610. I am going to tee into the tank return connection for the FEL. It connects with a JIC-M8 fitting that threads into the side of the transmission. If this is an NPT fitting, it is likely either a 3/8, or 1/2, but I can't really see the...

What's that deal with the recall of the seat used on the B7610, and can I still get a free or subsidized replacement? I just got an '05 B7610 with 127 hours on it (did the replacement need to be done before a certain time/hour?). Thanks, Jay

I just brought home my new (to me) B7610 w/ LA352FEL, Folding ROPS & R4s. It included a Kubota ballast box, a Woods PHD (not pictured), and a 5' rake . It is an '05, and has 127 hours on it. The only wear that shows is some scratches on the hood, and typical paint wear/rust on the bucket. I...

If all goes well, I'm going to be purchasing a B7610 tomorrow. I was looking at the specs from Kubota's web site, trying to determine the difference between the B7610 and the B2400, but I don't see any besides the quarter-inching 3PH vs. position control. Are there any other differences...

SAB Links anyone? I know BroTek makes em' for the BX's

I cleared a piece of ground here in New England for a half acre garden last spring. Seems like I'm picking more rocks out of the ground this year than last year. I'm running a KK II, and it does a great job, but I'd like to get the rocks out. Has anyone put a rock bucket on a Kubota? I've...

It seems my tractor (a 3 year old B7610) is showing signs that of developing a leak on the left front axle at axle flange interface. I did a search and see that this is the typical location for a leak on the front axle of these tractors. The "leak" is more of an oily film developing on the...

Any idea if a replacement battery is available from anyplace other than the dealer?? If yes where and a part #?? Thanks. . . .Skid

Sunday I tipped over my b7610. It wound up on it's left side. I wound up in the ER. major large bruise on right leg and severely bruised pride. I lost some hydraulic fluid so I called the dealer today to find out how much the new stuff costs. I then mentioned that I tipped it on it's side. The...

Hi I have a B7610. I love this machine but the 3 point can be a bit ridiculous. I have read some mention of a quarter inching valve, but my troubles seem to go beyond that. Sometimes when raising it seems to get stuck and wants to keep raising. I really have to pull at the lever to bring it...

Lost the bolt for the rear PTO cover. Does anyone know the size?

I've seen several references to such, including getting them off another kubota, but now I can't find the threads and the search on this forum is so broke. tia

Is it normal to have a little lash when going from fwd to reverse on this hst? It is small but sort of like with a worn u joint. It has just has the 300 hr (at 232 hrs) serivice and a complete look through by dealer as the extended warranty is about to expire. It seems more pronounced than on my...

Both HST, both with FEL. Both about the same hours. Any dif in adding a subframe BH? I'd add either a BRAND of tractor BH or a Woods BH (thumbs up). tia

What is the capacity of the stock charging system on my 05' B7610? I see that is has a 20amp circuit for work light provisions and 30amp for the solenoid. Is this a dynamo type system or is this a standard alternator?? Thanks for the help. I could not find any info in the owners manual.

Well after looking at a couple really nice B6100's the wife said why buy something that is 26 years old..... SO today I bought a 2005 B7610 with LA352 FEL, BX 2750 front mount blower w/ quick attach I believe, and Curtis cab with electric heaters. The machine has 135 hours on it. I think that...

Hello well my journey tractor hunting is contiuing... I looked at a nice low hour B6100 with Sims cab and front mount blower the other day but the wife was like yes it is nice but it is 26 years old why don't you look for something newer!!!! I was shocked!!! Anyways I found a used 2005 B7610...

Dealer has priced them both to me for the exact same price. B7610 is rated at 24 engine HP and 18 PTO HP whereas the B2320 is rated at 23 engine HP and 17 PTO HP. My understanding is that the B2320 is the new series that replaces the older B7XXX series. The B2320 feels a little more open when...

First of all, a big thank you to all the long time members of this site, who I have been mooching advice off of for a while. Your advice and lessons learned have been very valuable. I just aquired a Kubota L600 backhoe, and would like to use it on my B7610. The backhoe was given to me very...

i am looking at a b7610 and am wondering if the frame, etc. will take my b2400 stuff, like the blower/plow subframe, etc. thanks! eric

I am seriously considering selling my tractor and buy a newer/bigger with a cab. Here is what I have: 2007 (1.5yrs left on warranty) B7610 HST 298 hours 352 FEL 60"mmm 51"front snow blower *currently it has the WR Long electric solenoid valve/loader toggle switch with a ATI bolt on bucket...

Hello, Finally bought a Kubota B7610 with a FEL, front mount snowblower, MMM, and ballast box. Had a 1976 Case 580 B loader/backhoe, but Im done with the heavy work and wanted a nice smaller tractor that could still do big work when needed. Could anyone give me the low down on this...

My friends father was admiring my 6' rear blade,a Woods RB72.I like it and it works well for me on my B3030HSDC.Anyhow,he has a B7610 and we're wondering if the same blade would work on his tractor.I'm sure it would mount up,but it sure is nice to be able to turn it around while attached.We live...

Hi everyone. I've been looking at cabs for my B7610 for a while now and was wondering if Kubota makes one for this tractor. I know that there are several companies (Curtis/Sims) that make aftermarket cabs but I read somewhere that Kubota makes one. Can anyone point me in the right direction...

Wondering if there are rear wheel weights for the b7610? I dont want to fill the tires with fluid. Thought maybe someone would know. Also wondered about a different seat. I dont like the stock seat. I would also like armrests. We always had armrests on the old cub growing up and miss them.

I have a B7610 that's just short of three years old and has about 225 hours on it. Over the past few months I've "sensed" that the tractor does not have as much power as it used to have. For instance, to come up my rather steep driveway with a bucket full of material used to require that I set...

I noted a small leak near the upper 3pt arms.(the hydraulic arms) Just a little fluid running down the housing. It turns out it is from a hair line crack that goes from one bolt hole to the other bolt hole on the other side. This is that huge heavy cover that includes the 3 pt lifting ram. I am...

Hello Folks. Recently Purchased a Kubota B7610, also has an LA352 loader. This week I bought a 2733 Quick Hitch(not the 2733A). I would like to pick up a compatible rotary sweeper to use on the quick hitch. I was wondering if anyone has any experience with which model # is compatible with my...

My Kubota B7610 is leaking oil at the mid-PTO, and I want to replace the seal. Does anyone know where I can get directions? I have the service manual, but it doesn't cover this.

Ok- second wash since new. Sure looks shiny. But now it won't start. Didn't think I got it too wet. Any ides. Glow plug? Starter solenoid? First key position where glow indicator usually turns on, it doesn't. Second (start) position - clicks and nothing. Clicks again when I let key go bask...

I need to vent a little. My 7610 is barely a year old. Apparently, I waited too long to mow my field due to traveling. The field weeds and grasses were 3-4' tall. I noticed a leak under the front driveshaft after mowing. The dealer diagnosed it as the front drive shaft seal. The problem...

I'm considering moving up to a larger B series tractor (B3030). I currently own a 2007 B7610. The 7610 has 50 hours (just had the 50 hr service), LA352 loader w/ toothbar and has been kept in a sheltered carport and is in excellent condition. It also has the upgraded seat, hook welded to bucket...

I have a 2005 B7610 TLB with 156 hours. Any ideas on what it is worth? Thanks Mike

My father in law purchased a new B7610 hydro last year and can no longer use it. The tractor has 59 hours, quick detach 5' loader, quick detach belly mount carriage with a 5' 4-way snow plow. Because of his health it just isn't safe for him anymore, very sad time for all of us to deal with. I...

I went by a Kubota dealer's today on the way to a gathering I was attending, and saw a clean used B7610 with 147 hours. It has the LA352 loade with hooks, block heater, and loaded R-4 tires. It's clean, but used. Any ideas on what that might be worth? The dealer was closed, and it's not up on...

I just picked up the factory replacement seat for my B7610. The dealership charged me $40 for the seat. I was wondering what other owners were charged.... Anyone care to comment???? For those of you not familiar with the story; Owners who "commented negatively" about the factory seat (of...

I have a Kubota B7610 HST thats a little over a year old with about 200 hours on it. Two questions I would appreciate your help with: 1) I have recently begun hearing some sort of squealing noise that seems to be coming from the transmission. It is not an extermenly loud squeal but it is...

I am planning to install Kubota frame stiffeners on my B7610. These are the stiffeners required before attaching a Kubota 3 pt backhoe. The stiffeners bolt to the rear axle housings. This requires removing three bolts on each axle housing where they attach to the differential case and...

I'm back at it. Can't shake the thought. Put it behind me for a few months... it snuck up on me again. What is it? The B7610 of course! Before I delve into the payments, though, I have a few lingering questions. First, can I install a subframe (4-point, Kubota of course) to fit a friend's...

I have a hydraulic hose on my b7610 backhoe that has sprung a leak is it a big deal to replace. I worry about bleeding the new hose and removing air. Can someone give me step by step instructions Thanks Mike

Anyone know if they are still shipping B7610? I may be interested in one of these if the price is right for a old model. I don't really want to wait for the new model.

I am doing my first service.The stealer did the 50.The manual as you know isn't too clear on the Hyd.trans and Hyd.part of the service.I know from doing a search there are four drain plugs.Are they easy to find and tell they are a drain plug?Where is the strainer located at? Thanks in advance...

I was at my local Kubota dealer the other day and I was looking at the B7610 they had in their showroom (every now and then I think I should have gone a little bit bigger when I got my BX23) - well the salesman said that there is a 7610 replacement coming shortly - like in the next couple of...

Had my new B7610 delivered recently. I paid $14,300 minus $400 rebate for paying with cash so total was $13,900 out the door with LA352 loader, R4 tires (rear tires filled) and hook welded to bucket. I also got a 60 Woods box blade for $780 and added a toothbar for another $325. I also have a 48...

Can anyone tell me the difference bewteen these tractors, they both appear to be 21 HP compact tractors? I am looking at used tractors and have seen these two advertised by private owners w/loaders for around $10,500. They look very sismilar and have similar specs., so I am not sure what...

I am on 3.5 acres with about 2.5 or so cleared. There are woods on 3 sides of my property. It is composed of honeysuckle etc. It requires that I trim it back continously to keep my driveway open, keep the wooded area from infringing upon what is already cleared etc. It takes the better part of a...

I remember seeing posts in the past regarding a parts list, pictures and cost to convert a B7610 from chains to telescopic stabilizers, but all of the links I can find now seem to be dead. I know TractorSmart.com was one of the parts sources, but all I can find listed there is filters...

I have decided to trade my 3 year old B7610 for a B3030. Here’s the deal so far: B3030 HSD W/Turfs LA 403 FEL W/60” Bucket B2782 Front Blower Quick Hitch RCK2-30B 72” Deck Total is $24,411.00 + 6 % tax = 25,875.66 OTD I’m trading a B7610 W/325 hours, LA 352 FEL, 60” MMM, BX2750 front blower...

Here is my dilemma. I have been looking into/researching the purchase of a compact tractor for some time. See original post here: http://www.tractorbynet.com/forums/kubota-buying-pricing/88128-newbie-w-b7610-questions.html?highlight=b7610 I am finally in a position to buy (I am using cash...

I've been considering a B7610 to replace my BX. I looked around yesterday, and no one in this area has one that they want to sell me. (One dealer had a couple, but they were commited to another store location.) I guess the dealers can't order any more of the current version from Kubota. Does...

For the those of you that use a B7610, do you notice a change in sound between when the clutch is engaged versus when it is disengaged? Not saying it is a bad sound, but I can clearly hear a change in sound coming from the clutch housing. Everything else seems fine its just there is a change...

Hi, I'm looking for opinions on this quote: B7610HSD-F w/ 352 loader and loaded tires:$14,300 BX2750c front snowblower: $2,800 Woods GB60 box blade: $789 Total = $17,889 + tax. I figure I can get the box blade cheaper if I shop around. Also, I was quoted The same package w/ B7510 for...

I had almost given up on purchasing a John Deere this time around and had my mind made up to go with a B7610 but then a Local dealer started to compete and we are now at $14800. for Kubota and $15200. for the JD, 2320. Both would have a FEL and MMM decks. We will be doing a fair amount of...

I am looking at these two models and found that the TC26 actually appears to be a little nicer however it is a left over 06 model, turf tires, FEL and 60 in. rear discharge mowing deck for $17995, seems high. The B7610, R4 tires with fluid, 54 in. deck or can upgrade at extra cash to 60 inch...

Looking for input! I plan to purchase one of these two and found the TC26 seems to be a little nicer compact tractor however the TC26 is a left over 06 model, FEL, turf tires, no fluid and a 60 in. rear discharge mowing deck for $17995. seems a little high. The B7610 is a 07, FEL, fluid in R4...

The last thread I started concerned the problem of an uncomfortable seat on my 7610. I bought a new 7610 mid-March and now have about 11 hours on it. Two days after I get off of it I can hardly move. I always feel like I am sliding off the front of the seat and the seat pressure point is my...

hey guys, Has anybody out there with a B7610-7510 ever had a problem with the front axle leaking fluid?Its where the front axle actually steers on the outside end,theres a seal of some kind in there.About 6 weeks ago i had it back to the dealer to fix the right side,now the left side is...

I am considering selling my 7610 to get a bigger tractor. Good tractor, just a little small for my needs. (2 acre yard, 8 acre pasture) I bought the tractor for 13,500 last year. It has a 60" MMM, no FEL, 90 hrs.. My dealer told me that if I sell it I will probably only get $10-$10,500 for...

Bought a new 7610 last month and have about 5 hours in the saddle. I love the tractor and am totally satisfied that I made the right choice for my property. The only complaint I have is the seat. I'm not one to sugarcoat - bottom line it sucks. Do any of you guys out there have a solution to...

I want to install a horn on my B7610, so I purchased a Kubota Work Shop Manual and it doesn't show you how to remove the meter panel and panel under cover. The only photo is shown on pg. 7-S6 of the steering section, but it doesn't tell you how to remove these pieces. Does anyone know how to...

I am trying to decide between a BX2350 w/60" mmm and FEL and a like equipped B7610. The B is $14,900, the BX is $11,900. I drove both today just around the dealer's parking lot. I liked the feel and size of the B best. I'm just not sure the extra $3K is worth it. I have 10 acres, 7 in...

Hello I am in the process of selling my house and moving to a house that will cause me to no longer need my B7610. I am wondering what kind of range it might be worth....looking for thoughts.... It has always been taken care of and stored inside. B7610 352 loader with toothbar landpride 60"...

I was greasing my B7610 tractor the manual only shows 3 fittings.I thought they would be a lot more than that? thanks, tony

I am getting ready to sell my old King Kutter 60" finish mower that I bought used a few years ago. I would like to replace it with a 72" unit. However I am not quite sure if my B7610 can handle it. As indicated in this forum before, the manual and literature from Kubota gives conflicting...

Hi all. I have been lurking here for a couple of weeks and learning a great deal as I make this big purchase decision. I believe I am down to the two models listed above but I will give a brief overview of my research. I am not limited to a particular price but have determined a B7800 is as...

Does anybody out there know if theres a direct replacement, commonly available engine oil filter for the B7610,like maybe a Fram or some other decent brand?If so,maybe you would be kind enough to give me the brand,and part#'s. Gotta be somebody out there thats checked this out...

Hello Fellow TBN'ers, As part of the 50 hour maintenance Kubota recommends that the clutch pedal free travel be checked and adjusted if needed. I have tried to perform the measurements as provided in the manual and just can't seem to get repeatable and accurate measurements. I have tried dial...

Good morning, I was wondering if anyone here is using a 54" suspended MMM with their B7610, and if so, how they like this setup? I have a 60" RFM and am not satisfied with the way its wheels will mark the yard even if the ground is a little damp. I am thinking maybe the 54" suspended MMM may...

Hello To All, I am in ther middle of doing a 400 hour service on my B7610 and have a question. I replaced a blue HST filter and drained the front & rear plugs on the left side (sitting on it facing the steering wheel). There is a grey filer on the right side looking like it's part of the HST...

Hi All, I'm new to the forum but have been reading it for several months. Used to have a ~16HP Kubota with FEL, rear tiller and mower--should have kept it. My property is 2.5 acres of gently rolling hill with an irrigation ditch along the back 300 ft. of property. Mostly lawn w/short fescue...

I was checking my B7610 for a coolant leak and sure enough its the water pump. I still have a powertrain warranty but have been told the water pump is excluded. My question is this: It looks to me like if I take the radiator out it would not be too difficult to replace it myself. Has anyone out...

Has anyone ever considered or even intalled a set of R-4 tires and wheels from a B3030 or B7800 to a B7610?

I am getting ready to purchase a box blade for my B7610. Any recommendations on width? The manual calls out a 54", however most implement manufacturers offer either a 48" or a 60". Seems the 54" width is an odd size. Is a 60" box blade too big for the B7610?

Hello fellow TBN's, Since I'm relatively new to tractor ownership I have a question to the more experienced members. I was not real impressed with the finished cut on my lawn with my B7610 and a 54" MMM. I added Gator Blades to it and they helped a lot but I still have not been impressed with...

Anyone know what size lug nut wrench these rims take?

I have a B7610 which I am very satisfied with unless it's not starting. This occures totally random and not very often. After I use the tractor for a couple hours and I have to turn it off for some reason, I can not start it back up again. When I turn the key, there is dead silence. The tractor...

I'm getting ready to do an insurance audit to make sure I have enough home owners insurance. As part of that I want to get an idea of what my present tractor is worth. It is a 2004 B7610 with a 54" MMM, LA352 FEL, R4's & a 5' Box Scraper that I bought used. I think it is an older Landpride...