kubota b6200

I need a new battery. WalMart has a Everstart Group 51 410 CCA. Is 410 CCA big enough?

Hi All, I use my B6200 4WD with front loader a lot on my property which is also near wetlands and my biggest issue is that my front turf tires still leave a big mark on the grass, I wanted to know if I can put double wheels and how to go about it or at minimum what tire size with max width could...

Can anyone recommend a after market FEL in Canada, for a Kubota B6200d, or where I could purchase plans to build one?

I just picked up this Kubota the other day, I am totally new to PTO, I'm trying to disconnect the PTO shaft, Or do I need to take the front PTO off? I need to remove the Mower Deck. Any help would be greatly welcomed. Thanks.

Tractor: 1987 B6200 HST, D850 3cyl 15hp engine, Allied loader, ~2800 hours. Against my better judgement, I loaned it to a neighbour to use the loader to move some snow and crap from his horsebarn. I don't usually loan-out stuff, but this fellow is a decent guy, and always helps everyone, so I...

We adjusted our clutch like the book says. It grinds something terrible now and doesn't bottom out when you push it in. So we did it the opposite direction. It stops and grinds even less but it still grinds? What do you suggest now?

I was thinking of getting a box scraper for my Kubota B6200. From what I have read a 5' would be too big. I am looking for a 4' and found one on facebook marketplace near me. A 4' Countyline for $800, almost looks new. I googled them and it looks like TSC sold them except they only have 5' and...

B6200 4WD gear driven tractor. Built about 1988, has only 300 hours of use. NTL, while performing complete fluid change, ran into snag on the left front wheel sump. Someone before my time either over-tightened or cross-threaded the fill plug. It’s a little square headed plug about 10mm. I have...

Hi all, newbie to the Kubota forum. I have an older B6200E Kubota I inherited from my father in law about 8 years ago. It was used pretty regularly when he had it, mowing between the rows of Christmas trees. As we no longer have the trees, it has been pretty much just sitting, used occasionally...

I have an old B6200e. One of the front tires finally dry rotted to the point where it will no longer hold air. So i bought a good tire and when I took the rim off to put the new tire on, the valve stem came off in my hand. The hole had rusted through to the point where the rim is useless. So...

I know this is a long shot but here goes, I bought the tractor in 2005 because I wanted a tractor with a loader. I did mow with it a couple times then removed the MMM because I have other mowers. I have had it off for 13 years. I put it back on a couple weeks ago and have mowed a couple...

I have a B6200 gear drive with a FEL. I am getting ready to change the hydro fluid. Do I just drain the transmission case and not worry about the fluid in the FEL? Or is there something I should do to get fluid out of FEL cylinders? I’m replacing with Kubota UDT fluid. Thanks for any help

I have a B6200 with a loader. Low hours <350. Thinking of upgrading. What would it be worth selling outright vs a trade. Fredrick

I just noticed oil pouring out of the overflow (pcv) pipe and I can't figure it out why! The oil level and the fuel level hasn't changed. It's definitely seems to be oil that is coming out. I am stumped! It's not just dripping, it's like a faucet Help. could it be the hydraulic pump...

I have an opportunity to buy a Woods 750 and I was wondering if it's too big for a b6200? Its a 3-pt attachment. Thanks

Hi, I'm looking for the chrome retainer nut for the ignition switch and the air cleaner assembly and hose for a Kubota b6200d

I recently bought a b6200d and I need help with the ignition switch. The one on the tractor is missing the chrome retainer nut and my local Kubota dealer will only sell me the whole ignition switch and not just the retainer nut. Does anyone have any extra ones or any ideas of what I can use as...

Transmission Fluid: I need to add fluid to my tractor, but am unable to find the types listed in the manual (an old manual I found online). Anyone able to to tell me a common type that is available nowadays I can use? Maybe at Tractor Supply or Southern States?

Recently acquired an old B6200 2WD with belly mower. Had been sitting in a barn for years. Drained ALL fluids and serviced it out to the MAX. Very low hours on mower. Mowed with it for 3-4 hours, then the blades just quit turning. No bangs,clangs screeching, smoking.. the blades just stopped. I...

Dear members, My question relates to damage to my Kubota B6200HST rear right tire and axle (due to a runaway down hill with hitting a tree). The right rear tire rim was deformed about 3 inch inward buckle and was deflated. The right transaxle outer oil seal was displaced and the tractor lost...

I need some parts for my B6200E that Kubota no longer offers. Specifically I need the parts where the shift lever fits in the forks to change gears. Anyone have an idea where I can buy them? Thanks for your help.

Hey All, Just found a Kubota B6200 on a local trading post with 680 hour, c/w 36"tiller and 48" 3pt blade. Asking price 5K$ tractor looks well maintained in pic, would this be a fair price?

I recently purchased a B6200 4x4 with a 48" woods finish mower and 5 ft Buhler Allied 3pt blower. It also came with fairly new fluid filled tires and front weights. Besides the ripped seat the machine is pretty cherry with only 800 hours. I was curious what you may think the value is ???

I recently purchased a B6200 4x4 with a 48" woods finish mower and 5 ft Buhler Allied 3pt blower. It also came with fairly new fluid filled tires and front weights. Besides the ripped seat the machine is pretty cherry with only 800 hours. I was curious what you may think the value is ???

I am selling my Kubota B6200HSE/HSD 2/4 and a front end loader attached the tractor has 510 hours on the clock. It also has a tiller, and a snow blower which can be attached to the front of the tractor. I am asking 15K for everything, is that too much??? They are in all good condition. :confused:

I have a 1990 B6200 with original paint. I just installed a new loader on it before I do the final install I want to paint it to match the tractor. I bought some Kubota Orange I (70000-73710) at the local Kubota dealer but when I sprayed my loader the colour looks much different (more like...

Brakes quit working and no movement in pedal. Anyone have a diagram on how or replace pads or pull apart and repair? Thank you

Hour/tach meter quit working on my Kubota B6200. Is there a fuse or do I have take the dash out (?) to get to the meter and check connections etc.? Is it a big job? I can't get to it due to fuel tank being in the way. Thanks, Ron

welp , friend of mine has a b6200 kubota that we just fixed the control valve on( replaced the relief valve assembly) now its puking oil after its ran for a few minutes. the oil comes out of the breather tube. anyone have any suggestions?

My mid 80s B6200 hst has 3200 hrs on it. Still runs ok, a few quirks, dents, and stuff, but solid. Allied loader, muratori tiller and finishing mower keeps the jungle down. Put a clutch in it at about 1400 hrs, springs in clutch hub blew up from tilling rocks. Anyone have a high hours B6200...

Hi All, Longtime reader, first time poster. I have a B6200 with the 48" MMM, front pto. Something catastrophic happened in the past (before I bought it) to the mower deck, resulting in the mounts bending slightly and the mower lifts catching on the belt shield and bending the 3pt lift arm...

Now that I have lights again (woohoo), I probably need to actually fix a seat issue. On the b6200 the seat is hinged in the front and sits on 2 springs. On top of those springs are (well, should be) plastic caps. I have one but not the other. I've had no luck figuring out what that part number...

Been working on this for a couple of weeks now, and am increasingly baffled..... A couple of weeks ago the tractor stopped while attempting to mow heavy, wet grass. No big deal, that happens. But this time the battery was dead. Also no big deal, it was installed in August 2003! Put in new...

Hi I just purchased a B6200 Kubota and it is so hard to start. The first time it started, we worked at it for an hour and had to boost it with fully charged batteries. I did bleed the fuel line and after a while it started. I turned it off and started it again no problem. Today, no go, it...

I have A JD 650, wondering if tire of a kubota b6200 will fit?

Hello everyone, Great site with great info, so thought I'd join in. Just picked up my first real tractor, Kubota B6200D with a Woods 145 FEL. Looks great showing 234 (or 1234) hours. Can someone help identify the year? Tractor data only shows serial numbers through 1988 but it seems these may...

I am very new to tractor owning but I have ok mechanical back ground. I have got a used kubota B6200 4WD tractor and the old owner tells me when it gets to operating temp. the tractor will stop moving forwards or backward, but it works great when you first start it. If anyone has ever herd of...

Has anyone removed the gauges and switches from the dash of a B7200 or similar machine. Im repainting it and when I went went to pull the dash apart tonight I noticed the switches didn't exactly seem to come out easily. I don't want to put much pressure on them until after I asked if anyone...

I am looking for used parts my B6200E tractor, engine model D850. The parts that I am looking for are the radiator and the dynamo. I got quoted $600 for a new radiator, OMG! That is a quarter of what I paid for the tractor 8 mnths ago. As for the dynamo I have been milking mine along...

I am thinking of adding a orange tractor to my collection. I have a green 855 nice tractor and came across a 1985 kubota B6200 has 205 hours runs great, comes with an after market FEL and rear mower. No smoke not hydrostatic . Think it will have some yard use nothing heavy. Any idea of ball park...

It has a loader and 850 hours. Haven't looked at it yet going this weekend.

Hello, I am a new member and own a B6200 HST Kubota for many years. I'm looking for a backhoe attachment that fits my tractor (preferably without having to make mods). Can anyone tell me what the part number would be for this attachment? I've searched the forums and threads within without...

Hey all, First time posting and need some help. I have a B6200 HST 4WD diesel with a model RC48-62H mid mount mower that I would like to find a deck boot for installing a pull behind DR Lawn & leaf vac unit. The deck boot adapter that DR sells is a unit that must be cut to fit. After...

Thanks in advance for your answers. I have a 1995 B6200HST. This year I am experiencing something new with the tractor. When I engage the drive, it moves foreward but makes a whining noise, when engaging reverse, it wants to stall the tractor entirely. The tranny fuel is indicating good...

Friend purchase B6200e with front mount snow blower , last ower past away , we are missing a bracket. The bracket we need mounts to the tractor , to engage your front mount pto , this drop box pulley assembly has a rod sticking out of the pulley box , and goes back along the side of the tractor...

Looking at this tractor for garden plowing/tilling and hauling/moving firewood. Rebuilt engine (bored the block and cam bearings and main bearing installed. All the pistons, rings, new oil pump, gaskets, bearings, came from Kubota.) No mower deck and no implements. Asking price $3500. Hows...

Recently I acquired a Kubota B6200 with a B850 engine. After installing a battery the engine was cranked. The engine ran at full throtle and the accelerator nor stop lever had any effect. I removed the injection pump and discovered the "rack rod" (rod that slides back and forth to control fuel)...

Recently I acquired a Kubota B6200 with a B850 engine. After installing a battery the engine was cranked. The engine ran at full throtle and the accelerator nor stop lever had any effect. I removed the injection pump and discovered the "rack rod" (rod that slides back and forth to control...

Just picked up an older B6200 with FEL, mower, and aerator. Needs paint, but low hours, and it runs well. The guy dropped it off for me yesterday, a great guy, and when I went to tool around the yard a bit after he left, I couldn't get it to shut down with the key. I had to pull the throttle...

Looked at a B6200 today. SN 61433, geared, 4WD, unknown aftermarket loader (pistons say "Chief"), back blade, 6' plow jury-rigged for loader (!!). 219 hours showing but likely 1219 or who knows, new foamed rear tires. New hydraulic pump within past 3 years. Cosmetically pretty darned clean...

can someone tell me anything about the b6200 kubotas??? i am about to trade a nice mitsubishi mt372 for one an i do not know a thing about them thanks

Anyone have a B6200?

Just acquired a B6200. It had been sitting for 6-7 years uncovered. It started up ok, but didn't have any power and only worked in low gear. I drained the hydraulic fluid and cleaned /replaced the 3 filters per the service manual. The fluid drained out water for the first couple of cup fulls...

Hello, Can anyone give me information regarding the B6200. I was unable to download any owners manual or parts info from the libarary. I sure would appreciate any help if you happen to be familiar or have any documentation avaiable. Thanks, ABud

Does the rear pto on the b6200 run counter clockwise like the b6000?

Not much to report yet. I plan on building a fel using P.F. Engineerings' plan. I won't be giving his secrets away here but I'll try to keep anyone interested posted on how it is going and hope to get some good advice along the way. The tractor is a 1983 B6200 HST 4wd with about 900 hours. My...

I have an older Kubota B6200. After battery replacement a few months ago the unit has not been starting. Initially it would turn over very slowly as if the new battery did not have enough power to turn over the engine. Then one day when trying to start the unit sparks erupted from the...

Anyone know if a John Deere 430 Loader would fit a 1983 Kubota B6200? Would it be too heavy? My Kubota weighs 1350 pounds with no attachments or weights on it. I suppose that in the least, I'll need to fab up custom brackets but if it could be made to fit and work, there is one for sale...

kubota b6200 2x4 wont recharge battery? any ideas of what i should check?

I inherited a kubota B6200D60902 and I have no book with it and I dont know what year it is. I need to change all the fluids & filters can some one help me out. I plan on using Rotela 15-40 and not use the tractor in the winter, The oil filter thats on it is a Kubota L24458 which crosses over to...

Hi. Been reading here for a while but have a problem. I have a Kubota B6200. Don't know how old. 80s probably. Battery won't charge, charge light won't come on, fuel gauge doesn't register. Runs OK and starts if the battery is charged. I figured bad regulator and got a new one. Can't get...

My Uncle has a B6200 that will not lift a rock rake attached to the 3 point. It will not lift very high even with nothing attached. It is not leaking fluid. It is old, dirty and abused. Any ideas where to start looking?

So I drained the oil on my B6200D but am wondering how much to add...I added one gallon but that measured way to high on the dipstick so I am wondering how much oil to add or rather drain out....I don't trust the dipstick a whole lot because it just has some scratches on it, no groves or marks...

I want to build some attachments for my tractor, can anyone shed some light on how much this tractor will put out of the aux port? and if i can connect quick disconnects to the ports, Please see the photo of what i think is where i need to connect ...... i would like to see how you may have done...

Hello Everyone. I recently purchased a tractor. I think it's a B6200D but on the left of the tranny it says B7100 on a aluminium sticker as you can see in the picture it is to worn to read a model number. the other thing that confusses me is on the left side of the frame near the front that has...

I have a b6200 with a front loader and a 3 speed trans. Recently put on a new control valve for front loader and changed hydraulic fluid and cleaned the screen on the bolt on the right side of the trans. The front loader works great and smooth but now the 3 ph will not lift even its own weight...

I recently bought a Kubota B6200 hydrostatic tractor. In addition to the rear pto it has a mid pto with the shaft facing toward the front to drive the mower from the rear. This past weekend I got a belly mower that came off of a Kubota B5200 gear drive tractor. Included with the mower was a...

I have a power steering "kit" from Kubota that will fit a B6200 / B7200 HST. It will also fit B5200/6200/7200 gear tractors. I have all the parts and installation instructions. My dilema is I own a newer (91') Kubota 7100 HST with a Kubota 1630 loader. Can this kit be modified (without major...

I'm looking for information on the subframe mounts for a backhoe for this tractor. I went to kubotabooks and downloaded a couple of the backhoe manuals to see how the mounts are made but have been unable to find a mount that looks like it will bolt to the tractor. If there is anyone here with a...

I have a B6200 with a FEL and no rear hydraulics. According the manual, rear hydraulics is an option. Anyone know what is required to add this? thanks

Is a B6200 big enough for a backhoe? I would like to find one for my Kubota.

Hello All I have just come across a B6200 4WD GEAR with 947 hours. Ag tires that are OK shape. Attachments include a Kubota FEL, Box Blade with rippers, and brush hog. The tractor does need a new key switch. The glow plug pre heat does not work on the key switch and the owner installed a remote...

Hi Everybody- I just bought a Kubota B6200D (sn64337). I dont know too much about it, but I know it needs some maintenance. The transmission oil is milky - I think water leaked in through a tear in the shifter boot. It has a B1640 front bucket on it. I imagine the same oil from the...

Hi all, I am looking at a Kubota B6200 (15hp, 4x4, no implements). Clean, no new paint, no seat splits, 450 hours (rolled over???), domestic machine. Owner is asking 6,600 for this machine (Canadian Dollars). Several Questions: 1. Is it adequate for my needs? I have a 5 acre hilly property...

My dad has given me his Kubota B6200 tractor with a B1630 loader. It has been sitting for quite some time. Got it started pretty easily, but the loader doesn't move. I know NOTHING about tractors....nothing. I'm currently ordering a service manual for it, but thought I'de pick some brains here...

My dad has given me his Kubota B6200 tractor with a B1630 loader. It has been sitting for quite some time. Got it started pretty easily, but the loader doesn't move. I know NOTHING about tractors....nothing. I'm currently ordering a service manual for it, but thought I'de pick some brains here...

I'm trying to figure out how where the heck fuses and the like are on this new to me (and very cool!) tractor and can't figure it out. Don't yet have the manuals, but quick help appreciated. Here's the situation: my hazard lights don't work (all others do) and there is no voltage at the bulb...

Greetings folks! Just bought my first honest-to-God tractor, a Kubotar B6200 with MMM. Cut about an hour off my modest 2 acre lot cutting. Diesel fuel gage not exactly accurate (never goes to full) but that's OK - it's not that far back to the house to refill. All lights work with the exception...

My neighbor is into buying and selling small kubota tractors as a hobbie. At any one time he has 14+ tactors.... I have been thinking about purchasing a tractor and selling my 4x4 atv (which i use to plow snow). One of the tractors he has for sale is a B6200 4x4 with a bucket. I am not sure at...

Last week I was filling in a trench with my B6200 HTS 4WD with front loader that someone else had dug when the ground gave way under left front tire. I guess I tried a little too hard to back it out with the front bucket and reversing the HTS. Finally had to be pulled out with another tractor...

Hi, I was wondering if anyone out there has replaced the ball coupling between the clutch shaft and transmission on a kubota B6200 gear drive 4wd tractor. It looks like the tractor needs to be split to replace the coupling. I am also looking for a service manual at a reasonable price. Any...

owning-ML-716850-ML-

Is $130 the average price of a service manual. Thats how much it is from the dealer. Are there any other places to find one other than the dealer?

Kubota B6200 HST What\'s it worth? I have a chance to purchase a Kubota B6200 HST 4x4 tractor. It is a 1988 model, has 630 hours, and the only attachment is a 48"MMM. I would rate the condition as a strong 8 out of 10. Best price I can get would be $5000. Does this sound like a good price...

I have owned this tractor for about two weeks. Charge light on all the time, only battery voltage shows on multimeter when engine is running, "dynamo" has about 24 volts ac output across the two wires out of it. Is my regulator shot? As always, thanks for any help. I have owners manual, but have...

Hey folks: Looking for a little guidance. I'm considering picking up an older small Kubota. These all seem to go in around the $5K price range, give or take a bit. I'm looking for HST, 4WD, hoping to find one with a loader already installed, and would want to eventually run a small backhoe...

I want to change the UTF and Hydro filter on my tractor but the owners manual did not come with it. Can anyone tell me if there are any other drain points beside the ones on either side of the Differential.

I was wondering if anyone out there has rebuilt a hydraulic control valve on a b6200 1640 FEL. The valve is working but is leaking by to tank when bucket is raised and tractor is not running. The valve is made by Danfoss and I have the kubota factory rebuild kit. I have owned the tractor for 18...

I was just wondering if anyone out there has rebuilt a FEL control valve on a kubota 1640 Loader. It was manufactured by Danfoss and it still works but is leaking by to resevoir. I have the the rebuild kit and debating on rebuilding it or buying a new valve. I have owned the tractor 18 years and...

I currently own a B7200E 2wd with a front mounted pto which drives a RC60-72 belly mower. It is a great mowing machine. I have found a B6200 4x4 with power steering,loader and a 4' bushhog. The 6200 has a mid mount pto. Can anyone tell me if it is possible to turn the gearbox 180 deg and have...

Hello, just purchased B6200HSE, (2wd, turf tires, 60"MMM, Trac Vac 3pth grass collector w/8hp Kohler, back blade, with 675 hrs, garage kept, $4000, Good deal?) My question is do they make a front mount snowblower for this unit? If they do, does the fact that I don't have an FEL make it more of...

Just thought I'd brag about my borthers new-to-him B6200 HST. Kinda unique in that it has power steering and 4WD. He got her cleaned up pretty good, too! (I know how we're all addicted to pics....)

Is it normal for the alternator light to come on at an idle and then go out when over 1000 rpm. Tractor runs great and no other charging problems. Love the discussion board!!!!!!!! Have solved two questions already in the last two months. thanks. arkydog

I have a Kubota B6200 tractor with 4wd;3cyl deisel;15hp; and a 1630 front end loader and a 5' box blade. It's well kept with 242 TRUE Hours. How much should I expect to be able to charge for my tractor ?

I'm looking to buy a B6200DT, FEL, and Rototiller, it has 650 hours on it. They are asking $8,900.00 for it. I live in Oregon I'm not sure if that makes a difference? I like the Tractor, it's a little bit worn, but do you think the price is good.

Anyone have an idea where I can find a shop manual for a B6200? Tige

Getting ready to buy a B6200 and am wondering if it is big enough to handle a FEL? Is their a specific model I should look at? Are they expensive? Thanks Tige

B6200 used. What\'s a fair $? I'm looking at a used B6200 4WD for about $4500. It looks garage kept and has about 600 hrs. Does anyone think $4500 is a fair price? Thanks.

I am considering buying a B6200 4WD, but I am not familiar with its features. It looks in great shape w/ 600 hrs. What year was this model made? Any advice?

CURIOS WHAT A B6200 HYDRO IS WORTH, NEEDING COSMEDICS,NO LOADER,AGS,Im thinking about buying,not shure the average value,thanks again-shifty

Just recently purchased a '85 B6200,and need to figure out how to get more hydraulic power. I have a hydraulic drive bush hog, wood splitter, and tiller on my 448 Case (Ingersol), that I want to run off of the 6200. The problem is that the Kubota puts out 4 gallons per minute, and I need 8 to...

does anyone know how to tell year by serial number?