front axle

Hello, Thanks for the add. I searched the threads and parts diagrams, but haven't had any luck. I am looking for a cross reference part number for the u joint on the axle shafts in the front differential. I looked on kubotas parts diagrams without success. Has anyone had any luck finding this...

I found this service bulletin in my searching and I thought it would be better to have here for those of us with these tractors. Tractors made after May 2011 should already have the upgraded axles and bearings. I think it covers all the Bobcat, Cub cadet, McCormick, model numbers as well. The...

I am in need of left hand front axle assembly for our cub cadet, Both the gears, 38T and 13T are needed. Any recommendations would be appreciated.

So was going to use my new Mahindra 2126 for first time today and started checking everything out first. I found my front axle fluid level is low. I can see some fluid down in the hole but it is not at a level high enough to register on the little dipstick. Clearly it needs topped off. But I...

I used to have one of these and loved the tighter turning radius of the wide front axle. It made backing trailers into tight areas much much easier in addition to parking lots and u turns. Now I have a ram2500 and a f350 drw and the steering radius on both of those is like a stinky turd. Do...

I've got a leaking seal in my steering cylinder and the parts books call out different parts based on axle production number. SBA344960440 for axle number 2F31713 or greater SBA344960206 for earlier axles numbers. Only numbers I can find on my axle are: KT1N0100 (last digit could be D...

Just got my 4047 back after losing it in a divorce. I had a thread going on the trailers and transportation section. Upon getting it home I wanted to give it a good grease and inspection. When I got to the right front I found this😱, three out of the five bolts holding the front drive to the...

My front axle locked up. It ended up being the pinion was ground up and catching on the ring gear. I got it apart and cleaned all the metal shaving out of the axle. I got a new ring/pinion and bearings. I got the new ring gear installed. I tried installing the new pinion but the front pinion...

Hey guys, Need some advice/opinions on a IH 254. I changed the front axle gear lubricant last summer. 85-140 per operators manual. I used tractor all summer, fall and winter. No issues. The other day I noticed some leakage coming from the top of the axle. Is this some kind of vent or something...

Hi guys and Happy Thanksgiving ! The front left axle seal has been leaking badly, I just pulled the casting apart, pulled the bearings and big bevel gear and see the front axle seal. It reads AE2074F. This is actually the axle seal, not the steering pivot seal I've read several threads about...

Hey guys some what new to thread. I am needing help i am rebuilding my front axle I let bearings go dry seals went bad got water in axle destroyed the bearings. [ rookie move ] I am having a hard time trying to get the front pinion shaft out of the housing if someone has a manuel that shows the...

Have a NH boomer 37 (2016-ish) where the front axle seal started leaking. Opened it up and found the shim had disintegrated and screwed up the seal. Ordered replacement seal and shims, but they don't fit. OIL SEAL MT40188939 It was superseded by MT40334121, Ordered both, neither fit, the axle...

I've had my LS MT225S for 2.5 years, and it has been a great little tractor. Well, until this summer. In July, the loader valve started leaking whenever the lift cylinders were pressurized (so any time the tractor was running, because one must lift the loader to go anywhere). While waiting for...

Ive got a new to me 2008 branson 2910i and am going to do a hyd fluid & filter change but not sure what to use in the front axle. Do it take the same fluid or do you use gear oil? Would like to find an owners manual but no luck so far.

Good afternoon. I have a TC55DA EHSS that has a worn pivot bushing boss on the front axle housing. Has anyone had any luck welding these and machining the weld back down? Couple of questions… Is the axle housing cast iron or cast steel? I need to know some specs on the stub boss ie what is the...

Hey everyone, I've got a leaking front axle at the pivot point of the final case. I've raved the case, bearings etc and can't see where to split final case a from b. I have the service manual but it's not terribly explicit.Appreciate any help you might offer.

I am looking for the front axle and bearing for a Yanmar 1510D. The 4 bolts came loose and the broke the axle and bearing. If anyone has a front end final drive both the right and left side are the same. In the attached picture the axle without the bearing is the broken one, right at the...

so ive been diligently going through this used tractor i bought with 600 hrs. ive replaced all fluids and filters, worn parts in shift linkage, suction screen, small repai to SSQA, battery replace, few cosmetic paint or broken plastic repairs ect. im down to the last few things on my list, AC...

IH254 with 1160 hours. I am looking to change the front axle oil. Manual calls for 85W-140, but doesn't say how much. Does anyone know how much is needed to fill? My best guess is maybe 1.5 gallons. Just a visual guess...... I just want to make one trip to parts store. Thanks.

I have a Kubota 2380 leaking all the hydraulic oil from a spot near the front axle, circled in red on my picture. I'm trying to find what this part is called and how I can repair it. I'm looking in the manual and on forums/youtube and cant find anything yet.

Hi All, I need to replace both sides of front axle oil seals (between gear case and final case - leaks) but I am not sure if I have to take off the whole gear case (as described in manual) to do it. I would rather not have to do that in case I mess something up. I've attached photos of manual...

Have a BX25 with 500 hrs. I get a clunking sound from the front axle. Hard to say if it's from from changing directions or turning or a combo of the two. Fluid seems to be full in the axle. Or could it have to do with the 4WD? Just thought of that and not sure I've taken it out of 4WD to see if...

Has anyone performed work on their front axle / 4x4 system on a Massey 1652 or similar? (Should be same as 1547, 1648, 1652, 1749, etc...). I've got about 1500 hrs on my 1652. Great machine, no previous issues. During some heavy loader work recently, I've developed an issue with my 4x4. I...

Trying to locate a good front axle for a yanmar ym240

Anybody know where I can purchase the large U Bolt on the Farmall Super A front axle? Thanks

Hi Guys, I'm in Canada, and looking for a 12mm pipe plug/drain plug socket for the 4 drain plugs on the T25 front axle. Im not a fan of using open ended crescent wrenches on hard to remove plugs, inevitably they get gauled up Looking everywhere I cant find a 12mm. I find 10mm and lots of...

I have a B7800 that has been leaking hydraulic fluid from the front axle. I had it in to the dealer a few times, and it is still leaking. The first visit was a seal replacement, and it leaked within a day or two or getting it home. They took it back and put a 'speedy sleeve's in, and it...

Tractor 2016 XG3025 362 trouble free hours . I saw a little axle oil on the inside of my left front rim , for most of the winter it's been setting . i looked under the front end for a vent tube didn't see none , went and check manual there's none only vent the axle has is the blue threaded cap...

We have enjoyed our 2002 TC35D hydrostatic front wheel drive tractor and “built” our 20 acres with it. My husband uses the front end loader nonstop, pushes pulls and hauls. We have had the front axle worked on before. The very gifted Mechanic Has been able to actually weld in order to re-create...

I'm looking for front differential Ring and Pinions gears for my tractor, they were damaged, removed before I bought it. The tractor runs great but I sure would like to have 4wd option. It seems the gears aren't available for purchase anymore and I can't find any used places that have any. Any...