ford 4400

Does anyone know if its posible to install a hydraulic remote on a 4400. Asking cause everything i see is a 4 bolt mounting set up. When the actual lift cover block off plate is a 5 bolt system. Last thing i would like to get done due to having it as a usable Tractor. D4014C OH18B *C281244*...

Is there a place to buy a complete decal kit for a Ford 1970 4400 utility model?

Hi everyone, I have an issue with my 4400 three cylinder diesel. It has original 2600 hrs and always started fine down to about 30* with no glow plugs or block heater but the last week or so it’s been hard starting but ran ok. Two days ago while I was running it, it started blowing plumes...

Maybe longer. It's a 1969 Ford which my father bought in 1975; it's been stored inside since then, and hasn't seen a lot of use in the last decade or so. About 4-5 years ago he advertised it for $4000, got all sorts of low ballers, one person offered 2K saying "it doesn't have rear remotes", so...

I am restoring a Ford 4400 Backhoe/Loader - Model44021 Gas - 1967 I am trying to locate a source for parts, specifically a wire harness, radiator, front end/grille, gauges, odometer, etc. Can it be changed to an alternator or is that too difficult? What would be the benefit of changing it if...

I have a 1974 4400 and lately when I start the engine, the steering steers the wheels all the way to the left and it is almost impossible to bring back unless I use the loader to raise the front wheels then it is very easy to turn back. Someone said that it is an adjustment on the steering...

Brand new to forum(s) and forum Etiquette so don't bash on me too much. I am just a shade tree mechanic and tinkerer. About 10+ years ago I purchased this used 1971 Ford 4400 tractor, mostly to cut grass with a finish mower attachment. We did the usual new spark plugs, points, wires, etc...

Looking for assistance repairing and Restoring to normal use, Please! The radiator is the first step... the numbers on the radiator are: C5NN-Z-68A-ONG TM CANADA. I haven't located the SN of the tractor yet... but I am getting many numbers from around the tractor. The castings on the tractor...

Our Ford 4400 Industrial has started to not want to turn to the left. Turning to the right is easy, but trying to make a left turn you have to fight it. Anyone ever have anything like this happen? What are we looking at, Steering pump or the cylinder which is under the radiator.

Hi guys. I have a 3cyl. 4400 that's having some 3ph issues. I rebuilt the pump, all new orings and seals in the lift cover. The 3ph will go up/down and hold with no problem but there's only 300psi when I check the remote valve. There's good flow, it shot a good stream of fluid into the bucket...

hello my name is Dallas and i am new to this forum I have a 4400 ford tractor and the 3 point lift only raises about half way then stops it is strong and will hold for about an hr after shutting engine off when it is raised and running the lift drops about 1 inch then goes right back to about...

Hi there I'm about to undertake an in frame engine rebuild on my Ford 4400 TLB. Backhoe is currently off the tractor so it's just the loader on there at the minute. Has anyone ever done this? I have the Ford 201 diesel overhaul manual so I'm good on that front but I've read that the loader and...

Hi all. I have a 73 Ford 4400 with a torque converter/power reversing transmission. I'm changing all fluids/filters before I take it to the farm. My question is, can I use Case TCH in the shuttle trans and be ok? I use TCH in my dozer shuttle and they're about the same vintage. I would sleep a...

1969 ford 4400 loader hydraulics went out suddenly. I was using it to dig up a little dirt and it just quit instantly, no noise, no smoke, no spray or puddle of hydraulic fluid, fluid reserve is full. It won't even try to move the loader just like the pump died instantly. Any ideas other than...

From what i can see its a TRACTOR#C227155 MODEL# #D4011K UNIT#? 9012B ENGINE#8M4B TRANS#9A16B REAR#8J23B I picked up the battery, 4DLT(huge), new cables. Got the oil (Rotella), oil filter and fuel filter (fram) all stock at TSC. Best price on the battery, I called around. While taking the hot...

I have a early 70s ford 4400 industrial. I'm looking for the oil filter parts# and which weight oil does it take Its a Diesel model. Also the battery that's in it is to tall its hitting the hood and melted the ground wire. anybody have a cheap fix? I'm also wondering if there are glow plugs...

Just acquired a Ford 4400 with a front end loader and spent 2 hours online and pouring through manuals trying to find out where to check the FEL hydraulic fluid level and add fluid. I finally found the answer and thought I would post it here to cut down someone else's search time. The loader...

Field to battery, got the spark but still no voltage increase (11.9). I removed the belt and took power to the armature, it started spinning instantly. I thought I had to ground the case before it would spin? I'm thinking something inside the generator is grounding out but I'm not sure. As...

I am trying to find a grill for my 4400. It appears to be a one piece without headlights.

Help! I'm pretty new to tractor ownership and I don't want to do things wrong. :) I have a 1969 4400 Industrial with a FEL. I've noticed a slow leak where the brake petal enters the rear axle, and I'd like to top off that reservoir before levels get low enough to cause an issue. I have two...

The piston rings on my 4400 are in desperate need of replacing. I have found kits for this engine for less than 400 bucks and with new oversized pistons, rings, sleeves and bearings etc. The engine is a 201 diesel 3 cylinder. Is this an in frame repair or does the engine need to be removed for...

Ok so I have a ford 4400 that is incredibly hard to start the tractor has compression and the fuel pump and injectors have been rebuilt. The starter has also been replaced. Once it is running it is easily started. I think the injection pump timing might be off. when it is running it really rolls...

Last week during a -10ｰ cold spell, I connected a battery charger to my Ford 4400 gas tractor to boost the battery for starting. I have an inline tank heater for warming the engine and the water lines w here warm. When I turned the ignition switch, the starter engaged, but it cranked slowly...

Have been working on this for a while. Started when battery cable behind battery box shorted out and fried starter. Replaced starter and charging light came on and would not go out as rpm up. Pulled generator it was good, replace voltage regulator still light on. Checked continuity from field...

Hi there i am having a problem with my 753 backhoe that is mounted on a Ford 4400 1965 i believe The dipper cylinder is bent again and i am starting to consider that my pressure relief valve is stuck, dirty or needs adjustment The only diagram i have of this assembly is on the New Holland...

I have a 4400 that has a blue belly and yellow top. It has a loader. I am trying to find information about this tractor. Part of the serial number is missing.

Howdy y'all just resurrected an old Ford 4400 tlb-backhoe is a 755 i believe Just got the backhoe working and bent a hydraulic ram digging out a huge stump The casting also broke on the top of the ram where the dust seal sits Whats your best advice? Replace or take to hydraulic shop for...

I've had this tractor for almost 2yrs and now I finally have the time to start getting it in working order. I bought it for the loader and some other parts, then I was gonna scrap it. It runs so good I decided to keep it and fix it. She's far from pretty and needs a LOT. To start: 3PH doesn't...

The power steering cylinder on my Ford 4400 is tucked up inside the front frame, under the radiator and has sprung some sort of a leak. With the front end loader on, I can't see enough in there to tell what is going on. Does anybody know the best way to get to that cylinder? It looks like...

Hey guys, I am looking for a water temp gauge to replace the one in the dashboard that is included with the instrument group. The instrument group on my tractor is kaput and I am not spending almost $200 to replace it. I am going to mount it in the dash with the oil press and ammeter gauges...

I recently purchased a Ford 4400 '65-68 three cyl. and I am going thru it bit by bit and replacing/fixing the obvious. I drained the trans oil today and it was caramel color and I know it has water in it. I also drained the rear end and that just looked like very old oil but not carameled like...

hydraulic arms for 3pt. hitch wont lower? service manuals address failure to lift in the troubleshooting but not lowering....actually nothing happens. i removed the backhoe. capped low pressure(largest line with plug provided and looped from hose to pipe on both the backhoe and tractor. there...

Hi Guys ....Thanks for all the info. I am a 1st time tractor owner and i aquired a 65 ford 4400 tlb? so im told i have a full set of service manuals. I am mechanically inclined. I will have many more questions than answers, but i guess everyone starts somewhere.

Hi All, I have lurked here many times as I have been tractor shopping for a few years now. I am finally getting close enough that I have a specific tractor to ask about. There is a ford 4400 diesel for sale locally. I am hoping to go see it this week. Dont know much about it yet, it has recent...

Hello, I am looking at buying a 1972 Ford 4400 Utility tractor with loader. The front end has some issues. I am told it was converted to four wheel drive at one point. Then the four wheel drive axle housing blew apart and they had to weld the front hubs on because the original front end was...

I have a ~1970 Ford 4400 (3 cyl gas) and I've put just about 10 hours on it - hour meter says 1,100 or so. I was doing some mowing today and it just stopped running - like it ran out of gas. I checked the tank and there was plenty. Tried starting it a couple of times but all it did was crank...

I have a ford 4400 3cyl. Today when I attempted to engage the pto, the shaft snapped off about 1/2 inch from the outside of the case. I can see the end of the shaft inside the hole that it fits in. I was wondering how I go about repairing this. Is this a big job? Thanks RAY

I have a very old Ford (50's ?) with a FEL...the tractor number is C 204620 Model 44021G..Can anyone help with the valve lash or gap?

anybody know how to drain hydraulic fluid from machine an where can i get seal kit for pump?or replacment

Lookin to purchase a ford 4400 loader/backhoe or equivalent.

1971 Ford 4400? (Pics added) Howdy folks, I am looking at a 1971 Ford 4400 with front loader, 2900 hrs on the clock. It's the Industrial Model. The tractor needs paint/beautification, but seems to be in good working order. Does anyone have any experience with this model? Are there any quirks...

I was bushoging yesterday and noticed my pto shaft was not spinning. I looked where the shaft entered the housing and fluid was pouring out. The shaft had slid out about 6 inches and destroyed the bearing. After removing the drive shaft for the bushog I pulled on the pto shaft and it pulled...

Well I put a deposit on my first tractor a 70 something Ford 4400 with pto and fel:thumbsup: It runs good, is a little rusty, but overall I'm in love. Tractordata.com shows a 6 speed, 8 speed and 10 speed. This tractor has two levers coming out of the tranny. Right one is a hi/lo, the left...

I've been looking at a Ford 4400 industrial tractor - used, good hours and good condition. Has front end loader and backhoe installed - good hydraulics. About 80% of the work I need to do will be with rear PTO and 3pt hitch attachments. But I could use a backhoe, so I am considering it...

Hello, Came cross another backhoe ad on craig's list and seller was asking $2,800 OBO. Came in and had a look then paid $1,500. It needs some works and possible engine rebuilding but I still thought $1,500 was too good to pass especially when it still runs. Managed to find qualified mechanic...

Howdy guys, I am new to this site, but not new to tractors. I have a Ford 4400 loader/tractor that has a blown head gasket and some blow-by. After removing the head and inspecting the pistons and cylinder, I found the pistons are marked '040'. This tells me the cylinders have been honed .040...

Been thinking about getting one for my tractor.I can't find any new ones only used ones. Do you disconnect them alot or just leave them on.Only ones i find are bolted on,no quick disconnect. My tractor is only 2wd and not 4wd. The price of a used one is $2500. I was thinking maybe i should sell...

Ford 4400,won\'t charge I'm having a hard time trying to figure out what is wrong. Fixed the Generator and the battery is less than one year old. How do i check to see if the battery is getting a charge or not? Thanks Jake Found this site and i love it,makes me feel like getting a new tractor...

In my continuing quest for a tractor with a loader to run hay equipment, I saw an ad from a dealer in Vermont for a Ford 4400 with a loader. I know it's an industrial tractor. I called them and it has a three point hitch (not all industrials do), and they say it runs well and is in good shape...