Search results

Ah, the old GM plant in Shreveport. ELIO Motors scammed A LOT of people out of reservation down payments with the commuter car that never was. ELIO was going to use part of the old GM campus for manufacturing. CT

Have a 1978 Troy Bilt Horse tiller. Not a safety device on it. Wife refuses to use it. CT

"Am I being overly paranoid?" I think maybe. If transfer tank is clean and you have a filter on it after the pump, I'd send it! CT

Troll

I have had this for many years. Have had 0 issues. Has a CAT pump and Yamaha engine. Yamaha PW3028 Yamaha PW3028 Pressure Washer CT

I have seen them in MO and OH before. Never seen one here... CT

Have a 1984 C10 Silverado with 140,000'ish miles. 6.2L N/A, OD Auto trans, 2wd, 25+mpg. Just do not get in a hurry and it isn't set up to tow heavy. CT

The 6.0L Vortec doesn't have the DOD and the associated lifter issue. Always on all 8 cyl. CT

Sharp truck! Mine is black also. I am still driving a 2013 GMC DenaliHD 6.0L Z71. Just turned 150k miles, mostly trouble free. Replaced radiator recently and still on the OEM brake pads. No desire to own an emissions era diesel. 360hp/380tq is adequate for anything I hook up to. CT

Tractor Supply Co has 6v battery for $109.99 last week when I was there. CT

It is a skill to learn. Have to think like a differential in an axle. When turning, have to slightly reverse one side while other side is turning forward. I can go back and forth turning 180 at each end and not scuff the turf. Have had 2 different ZTR and have used several others in the past...

Will require adjusting the voltage regulator to about 9 volts. Or just use an 8 volt Battery Tender maintainer if it is a occasionally used tractor (which I'm sure a JD M is). CT

Also, GOOD #2-1/0 welding lead copper cables. Parts house #4 cables do not work well on 6v. CT

"8 volt battery? You gotta be kidding. If 6 volt is rare then 8 volt is in the Smithsonian." 8 volt batteries are common. CT

I see a good sized tree branch that you do not notice will "adjust this for you. It really needs some support near the canopy. My LS P7010C has a vertical stack that runs up by the cab. Has a support in a rubber grommet for vibration and movement. 800+ hours and its still in one piece. Otherwise...

Saw one yesterday. One. CT

Saw one at TSC yesterday. Think it was about $130-$150. Batteries are expensive, period. CT

Have a 2103 GMC, 6.0L, 3.73, Crew, Z71 4x4. It will pull almost anything. It likes RPMs when towing. It can drop into 2nd at 60mph tach over 4000. Not concerned a bit. ECU will not rev engine to the point of damaging itself. They do not provide the best fuel economy though. I usually average...

LS P7010C has 540, 750, 1000, ground drive PTO options. I mow with a 10' Kodiak 2 spindle in 750 at about 1400-1600 rpm. Can go through about anything in M 1-4. CT

I have thought about mounting a 8k-12k winch on the front of my P7010C. Battery is right up front. Have had a few times I have got in a bind and it would have recovered itself. Can also use it for recovering other things too. CT

This. One of main reasons I went cab tractor. I have watched bald faced bumble bees attacking the glass more than once. Yellow Jackets... Not as concerned. CT

They work. For niche applications. I have an electric, lifted cart. Limited range vs gas and I have to carry a generator to recharge when remote hunting. We have a fleet of about 20 electric fork lifts, indoors, no emissions. But require a battery pack changeout between shifts. Takes 2 battery...

They have a 70 HP model for $74,999. No loader. CT

Looks like my pond. At least I was able to spray the water weeds, then bush hog them down. Has been raining here some. This week is supposed to "bring on the noise!" Raining heavily right now. CT

Some PTO pumps also have a thru shaft. This PTO extension allows use of a PTO implement while leaving the pump in place, permanently. Example, PTO pump to run a loader. Need to power an implement off the PTO and use the loader. It's a clumsy way of doing things, but works. CT

That's cute. 100 degrees, dust and bees. No thank you. CT

I have 800 hrs in 8 years on a 72hp cab tractor. Mainly mowing 50 acres and road maintenance. CT

When he starts his truck until he parks his truck. That's how I would charge if by the hour. CT

This. I run a 72 hp tractor and a 10 foot cutter. I use Google Earth to draw out the area to get acreage. Estimate how many trees and such to trim around. The shape of the area. Is it square or many point rows. Then knowing my acre/hr/overhead, bid flat rate. Fresh or sharpened blades will...

I do not do any mowing jobs more than about 10 mile out. I also road the equipment. Enough to keep me busy. CT

LS P7010C and JD 6420 will too. Have to jump on them fairly firm, actuated by the brake light switch. Assist in braking. With MFWD engaged, both axles are tied together, the rear brakes then also brake the front wheels.

This looks like a nightmare... To plant 150 feet of "bushes" in. CT

Definition of "expensive"? What is your time worth? 150 feet of "bushes" doesn't sound cheap either. Plants are expensive, IMHO. Tractor Supply Co sells them. $600 for County Line powerhead, $200 for 12" auger. Will last a lifetime, then some. I have the County Line powerhead with 6", 9", 12"...

This is what I was expecting it to look like. My LS P7010C axle is similar, just 2 as big. Takes about 4 gallons of gear oil to service. CT

Self leveling doesn't work like that. It keeps the angle consistent while raising and lowering. It is awesome. Auto leveling? Have not seen that on a tractor. CT

I had to Google this. Checks out. Sneaky bastards! CT

One of my favorite movies of all time! CT

Wife's 2014 Jeep Grand Cherokee has a cap-less fill. And was a source of multiple trips, under warranty to the dealer. Would get a minor or major EVAP CEL. Remote start will not work with CEL on... CT

I remote start almost daily in the summer. Amazing how much cooler it is inside a black truck when you start it from the other side of the parking lot. CT

Almost everyday. CT

I am impressed. Did not know what to expect while reading the description. You have more blade than traction. Which can be good at times! Very nice fabrication work. CT

$160 bare tool for Ryobi. It is very well built and makes me want to use a grease gun again. CT

We upsized mowers. 18hp 44" Snapper to a 25hp 54" Bad Boy. Went from 4 hours to 2 hours. 4-5 acres we cut as "yard". Wife likes to mow. CT

Like my Allis Chalmers 180. Big straight 6 will drink 5 gal/hr when working. CT

In some states, they will pull you over if you just have a gooseneck with a tractor or hay. Commercial or not. Scales, emissions, whole deal. Personally I've never been stopped. I do not run diesel trucks, but have ran heavy. CT

Good old Commifornia. CT

With enough traction and balls, it can pull a pan. A CUT isn't going to pull a pan. I can make a JD 6420 spin all tires with a 4 yard Reynolds pan. CT

These work. Have shaved many a hill and built many a levee with a Reynolds 4 yard pan. How much HP/weight tractor do you have? Old school 50-60 HP row crop tractor is 1st gear hammer down. 110hp 4x4 tractor will spin all 4 if dig too deep. Moves a lot of dirt. CT

For that acreage, I'd step this to 60-75 hp. Budget is small. LS is solid brand. On our farm we have LS, IH, JD, Ford, Case. CT

Think the Glider Kit loop hole is closing. Also, believe that California has/is making it illegal to operate pre-emissions commercial vehicles. CT

Zero Turn with open fab deck. Best solution. CT

Worse case scenario. A truck and a trailer. I'm out of warranty now, never had to use warranty while it was active. If needed, I have a 20' trailer, a winch and a 2500HD truck and I would trailer it 35 miles. CT

I do not doubt the grapple's strength. The video showcasing the grapple is nauseating. Who publishes a promotional video using a +$100k farm tractor as a poorly used bulldozer. Thought this was Whistlin Diesel at first. CT

I haven't seen this picture in over 20 years. Huge far side fan. CT

Grind it out and reweld. Looks like the weld was cold to start with. New pin, washer on fastener end and use a cotter key. CT

Mid mount mowers can be a PITA. Zero Turn will be faster and maybe even a better quality cut. CT

I vote for LS. 8 years and 800 hours of trouble free operation. CT

My Rhino 172 is setup like that. Sheared many of grade 8, 1/2" bolts between the slip clutch and gearbox. It has a circlip, snap ring, something. It never did anything but spin on the shaft when bolt would break. CT

My 72" grapple looks almost identical to this Tomahawk grapple. Tomahawk 2 Cylinder Bought it new at an auction. Only had a made in USA sticker and no guards around the cylinders. The profile and design look spot on. CT

I can snap a picture when I get home of mine. It is about 72" and has 2 cylinders and 2 grippers. Bought it new at an auction probably over 10 years ago. It is not the heaviest, but have not bent it yet. Think it cost me about $1300. Was setup for skidsteer and has skiidsteer hydraulic...

BUT IT IS NOT ORANGE !!! :mad::mad::mad:😤😡🤬🥵 Kidding of course! That is a nice looking machine. You should have no regrets it is BLUE and says LS. Had our LSP7010C going on 8 years and 800 hours. Get it dirty! CT

Interested to see how the R14 tires preform on a larger tractor. They look mean! Personally I have no use for R4 tires for farm/acreage usage. They absolutely suck in soft ground and mud. I have stuck a 30 hp more than once with R4 tires. Also they suck for pulling ground engaging implements...

You need a few more remote valves back there! Did you plumb this? CT

Yes. Basically everything but range shifter and shuttle shifter are on the right side. Ergonomics of the LS cab was a deciding factor to buy an LS. CT

3rd function is nice. Keeps it all on the joystick. I had thought of adding 3rd function kit myself. Was $1000 in parts alone. Though what little I use the grapple compared to everything else, I just used a remote. Have about $200 in hoses and fittings. Have not had a need to use more than 2...

10 hp more on the shaft than gross power? Under rated at 135 hp? Test was an error? CT

In the "pull down" menu, it list P7010. P7010 is a mechanical injection, EGR engine. No ECU. No DEF. No Regen. I am aware of no electronic control modules on a P7010. What would this device do for a P7010 owner? Unless I do not know the in's and out's of my tractor and missed something. CT

Congratulations! Same story back in 2014 when I was shopping P7010C. Tractors, no loaders. Regional LS Rep found one in Biloxi or Gulfport MS and had it shipped to my dealer in Many, LA. It was the only P7010C available new in the country at the time with a loader. CT

Kodiak 10' HD cutter. American made. Old blades. Will put new blades on before next cut. These have found some concrete. Have edged them a few times. Deer CT

How to clean oil cooler, ac condenser and radiator on a P7010C. Fold grill guard forward and open hood. Locate the 4 hand bolts that secure lower body. Next remove 1 hand bolt holding condenser and loosen other 2. Slide plate out of the way. Unhook pressure switch harness. Now slide...

I have a 72" brush grapple with pinchers (like a crab or crawfish). Added these several years ago. When you have 3 remotes, you do not have to add a 3rd function to your loader. Skidsteer hydraulic connectors came with grapple (1 pair). My father bought one too. He wanted to use pioneer ag...

You stuck it well, friend. Had LS P7010C for 8 years, never stuck. Last year, stuck it 2x. About like you did. Required another tractor of equal size to get me out. CT

I have the 10 ft HD, 2 spindle. Bought it used and have used it to cut hundreds of acres. Very, very good finish when properly setup. CT

I saw these at HD. Looked solid. CT

First tractor was a 1962 Farmall 504 diesel. I put a new Koyker loader on it in 2008? Still have that tractor. CT

Very nice. The modern version of the P7010C with power shuttle. I almost bought the P7040CPS back in 2014. Did not really need 97hp tractor, but the power shuttle would have been nice. Keep us updated once you take delivery. CT

Usually 0% financing has the interest rolled into the purchase price. Nothing is free. Bought LS P7010C in 2014. Used my bank, commercial loan, like 5%. Still came in about $10,000 cheaper than a Kubota M7040 cab with loader. LS has 3 remotes. Kubota was about $1000 per remote, dealer...

Mine has 20 speeds... and a clutch! P7010C Transmission CT

Sicily Island, Louisiana This is where most LS tractors are final assembled. Tires and wheels are domestic. They are mounted and installed as part of assembly process. Also some LS tractors are shipped without loaders attached. The loaders are installed in Sicily Island as well. At least this...

What are you taking delivery of? CT

Does your AC condenser slide out? The AC condenser on my P7010C is on a track and the hoses have a loop in them. Remove 4 hand bolts to remove lower fairing then loosen 2 hand bolts to slide a plate over. Then unplug the pressure switch connector and the condenser slides all the way out. Can...

Correct, my thoughts also. It appeared over tightened from day 1. It has foam where it sits on brace and where straps go. Thinking 8 years and 780 hours of over compression. Split was at rear strap location, inboard lower corner. I only snugged straps enough to hold tank in position. CT

Have I mentioned I really, really like this 10' cutter? Needed to service cutter. Backing into brush and trees bent tailwheel forks. Also a hub had lost it's bearings. New forks. One 1". One 3/4". Both need to be 1". Strange times in the supply chains. Welded gussets on both sides of...

Sharpening ZTR blades. CT

Fuel tank replacement. Tank developed a split. Replacement tank was $754. Never empty when you need to work on a fuel tank. Found a grease fitting I didn't know existed. Greased it. Now clutch pedal does not squeek anymore! 777.7 hours Back in service! CT

Wife's AGM in her Jeep Grand Cherokee lasted 8 years. It is under the passenger seat, in the cab. CT

Add a new shed to the shopping list. CT

Agreed. My LS P7010C can lift a pallet of Redi-Mix out of truck or trailer. 80 LB x 42 = 3360 LB + pallet... I believe the 3500 LB rating. CT

Update. Changed 2013 battery in LS P7010C few weeks ago. Would be happy if new one last half as long. CT

Can confirm. Bought a used mini ex. Burned piles. Then dug holes, burned stumps and roots in pits. Covered pits when done. LOT OF WORK CT

I got WAY behind with this thread. Photobucket blocked pictures for a while and I gave up on forums. Now many forums allow you to upload directly, makes it easy to post pics! 773 hours. 0 issues since the Rat incident. Tractor is a beast. Just mowed about 15 acres or so with 10' 3pt cutter in...

It has been one of the most dependable purchases I have ever made. 773 hours. CT

I do this when I mow for a new customer in a new field. CT

Or Pontiac? Or Saturn? Deere has been around 150+ years. Farmers have to bootleg Russian software to work on them. CT

I usually have pallet forks or grapple on when mowing. Bucket rarely. Though pallet forks suck when trying to push out of mud. When cutting hay usually have nothing or a bale spear. CT

Update. Fuel tank developed a split. Weeping diesel. New tank ordered. $750 with TAX. Will document the tank replacement once I receive it. CT

Noticed a fuel leak on my LS P7010C. Split in fuel tank. 770 hrs and 8 years old. Called dealer I bought it from 30+ miles away, not the local ding dong. Part is ordered, it is in stock in NC and should have it next week. Pretty solid service IMHO. Tank is about $750. Price sucks, but equipment...

LS lift capacity is usually higher than any competitor in its power/weight class. CT

LS Bought P7010C in 2014. Rode it for 7 hours this weekend pulling 10' cutter. 774 hrs on the clock. CT

One of the reasons I went with a 10' 3pt mower instead of a 10' pull type or 12' batwing. Also cost... Yes, 3pt was much more cost friendly. 72 HP tractor, mow at 5-8 mph when terrain allows. Do not wear my seatbelt in a cab tractor. I cut 30-40 acres several times a year plus some contract...

Put 750 hours on a 44" Snapper 350Z. Selling it, out grew it. Had HydraGear pumps and Parker drive motors, Kohler engine. Was taking wife 4+ hours to cut 4ish acres of lawn. This season bought a Bad Boy MZ Magnum 54" from Tractor Supply Company for $3999.99 +T. So far it does everything my wife...

2013 LS P7010C Mechanical injected, turbo 4 cyl and a muffler. Hope it is the last tractor I ever buy. In no way do I want to deal with a post-emissions diesel. I have refused to get a diesel truck. A gasoline HD truck pulls everything I need pulled. CT

When I fill tires, I put the valve stem at 11 o'clock. Straight up 12 o'clock to check pressure. CT

13 lbs to the gallon. CT

I ran a Deutz 100hp air cooled 6 cylinder for a few summers haying. Loud was an understatement! Edit. Deutz D 10006 Tractor Data D 10006 (link) CT

Louisiana. 1 tractor loaded with pure, H2O, tubes. 1 tractor loaded with pure, H20, tubeless. CT

I love this site. I wish that they wouldn't have succumbed to political correctness. "Nice Price or Crack Pipe" sounded better than "Nice Price or No Dice"... CT

Appears she is the brains of the operation... CT

I'm going to be blunt. Last year, you agreed to till his garden for a price. He stiffed you. That defined his character. This year, you agreed to loan him an expensive to buy, expensive to fix piece of equipment. He sill has it. You sir are an idiot... I do some tractor work for hire. Mainly...

I run cotton picker spindle 00 grease in most of my gear boxes. CT

4 gallons of 80W-90. Traveller's brand from TSC went in my P7010C at 740 hrs. CT

I was thinking about a 72"-84" tiller just yesterday! Looks like KK is in the running now! CT

My bucket is bowed on my P7010C. 72 hp tractor. I have thought about some think like this. If not just to reinforce and straighten it out. CT

I have one similar. Think it came from Tractor Supply. CT

No seat switch on P7010C. Haven't ever been in a cab tractor with a seat switch. I would jumped that out 1st time it shut down when I didn't want it to. CT

This^ I bought a 105 gallon L shaped tank with 12v pump at an auction for $200. CT

I was reading this in the earlier hours of the day. My context clues were not on point! Though using your tractor as a gauge, I knew it was at least 7'. :cool: Natchitoches, LA CT

Are those TJI Joist for your rafters in the first picture? CT

Picked up a load of limbs with pallet forks and burned the pile. CT

I second this. Have a grey market Komatsu PC38UU. Rats got in and chewed up all the safety solenoid wiring on the valves. Had to do some rewiring to get the hydraulics to work again. Now it is down again. Starter possibly. Hope it isn't hydro locked. Will not turn over, just stalls out. Could...

I have that same landplane, but in brown (bought it at a Kubota/Land Pride dealer). Is your 7' or 8'? Hard to tell in the pic. Mine is the 7'. Wish I had an 8' CT

How loud is that Lincoln with a Cherry Bomb on it? CT

I do not use TapTalk on any forums. CT

We shall see how it holds up. We mow about 4 acres weekly. Fairly flat land, though rough in places. Wife chose this one. I was going to go Kubota. She like it. Retiring our Snapper 350Z. 780 hrs. Deck has needed some welding, but still cuts. Though it had independent Hydragear pumps and Parker...

Using a CUT with a MMM sounds like a horrible idea compared to a ZRT or Garden Tractor mower. CT

Bought a 54" MZ Magnum Bad Boy from TSC for $3999.99 with a 25 hp Kohler 7000 series engine. Cuts fast and clean. Even 12" tall rough grass at a decent clip. CT

This happened to my 2014 LS P7010C not too long after I bought it. Had it parked outside at the time. Chewed one of the injector return lines. Dealer found the part. It was the entire return manifold, about $580 at the time. Went to parts house, got some FI fuel line and clamps, fixed it for...

OP has been a member since Feb 2004... CT

I have gas and battery saws. CT

Personally have the 18V, 12" Brushless Ryobi. Can fill the bed of a side by side up 2x with a 9ah battery. CT

Ryobi. 18 volt. 12". Brushless. With a 9ah battery it will cut for a while. CT

Bought one of these to use in the shop for general mechanic work. Socket set, end wrenches, hammers, air tools, ect. CT

I understood it well. Can I borrow your Klein's to cut this wire? CT

Like the Midwest calls carbonated beverages a Pop. Westerners, soda. Southerners, Coke. CT

Agree. No heat. Cold bend. CT

That looks awkward AF... CT

I have had some that look like that just blow the belt out sitting. I run radials on my RV travel trailer. Bias ply on all other trailers (4 of them). CT

Its heavy, very dense. Easy to exceed tow ratings and equipment capacity. Most people do not even know what trailer brakes are, much less use them. Requires being tarped, otherwise creates safety issues spilling onto highway or hitting other vehicles. I can go on. CT

Makes sense. Wyoming. I saw irrigation in Colorado. In Louisiana we just get 70" of rain annually. Hurricane if we are lucky! CT

Sound and common sense. That's how I do it and haven't blown any seals. CT

I buy 20 tons at a time from about 10 miles away. Cost about $100/load for trucking. I then use cab tractor with the air on to move and spread. No way I'd have rock dumped into the bed of any truck I own. Not even the 1979 C20. CT

I have heard that like 85% of Mexico's fuel is imported from the USA. Also heard that the Mexican government stripped the taxes from the fuel to help the consumers (citizens) from paying more for fuel than necessary. Haven't verified this, but heard on talk radio this week. CT

I paid $420/cord last year. It was delivered and while I thought it was steep, I just pointed where I wanted it stacked. Not my idea of a fun weekend to cut up, split and stack a cord of wood. CT

Heard this on the news yesterday. CT

I do the same. None of my tires are over 5 years old, ever. Many see it as waste. I haven't changed a tire on the side of road in 2 decades. CT

<$1000 for complete system online. Completely DYI installation. If you are even somewhat handy. 1 3" hole through the wall. CT

Good tools aren't cheap. Good tools make work more efficient and enjoyable. 26 grease fittings on my loader with a lever or pistol grip sucks. CT

Ryobi. Cordless grease gun. If you have Ryobi tools. Bare Tool - Ryobi Grease Gun Bought my father a Dewalt cordless grease gun. He loves it. CT

We have shifted to Fronius from Lincoln and ESAB at work. High volume manufacturing. I have personally integrated 12, 500 amp Fronius power supplies into equipment. 8 are burning 0.52" and 4 burning 0.45" wire. Controlling them over Ethernet via a PLC. 500 amp multi-process power supplies, think...

Have welding machine, have hooks... Send it! CT

I have a 72 hp cab utility tractor with a 3500 lb capacity loader. Sometimes its too small! Having personally used SCUT through 300+ hp row crop tractors, I would suggest the 35-50 hp range tractor for you. CT

Years ago bought a 100 gallon "L" shaped tank. The one that goes in a truck bed with the crossbed tool box over it. Converted it to portable. 2, 4x4 skids on bottom. Use forks to place on a trailer. Go to town and fill. Bring it back home and place it under shed. Has a 12 volt pump that I clip...

Like the camera! CT

I'm aware location and methods effect price. We had about 35-40 acres clear-cut. Think it was +80 loads of logs. After logging I hired a contractor with 1 excavator and 2 dozers. They grubbed everything and piled. Took about 2 weeks, by the hour, came out to about $400/acre. CT

It was about 40 acres of clearcut. They grubbed and piled in about 2 weeks. CT

For OTR tires it is sound advise for safety and sanity. For off-road use, do as you please. I do not like tubes. Cannot slime a tube. Cannot plug a tube. I quit breaking tires down myself years ago. So much wasted time. Have had good results from Asian Truck and Trailer Tires. I'm in Louisiana...

Most likely the plastic safety sleeve. I have a 10' Kodiak 2 spindle cutter/mower I bought used. PTO shaft is slightly bent. I just send it. If it were worse, I'd replace or chuck it in a lathe and straighten. CT

Surprised they hold air. Check date code. Over 5 years, replace regardless of tread. CT

Rule of thumb is MINIMUM 5 PTO HP per foot of cutter. 53 engine HP/46.5 PTO HP. Math says 9.3FT. Granted, this is minimum HP required. 5FT cutter is way too small. 6FT would be good for field and woody stuff. Personally I would chainsaw anything over 2" diameter. Period. Regardless of cutter...

WOW. 2009 I paid $400/acre for an excavator to grub stumps and a 2 dozer to pile them. CT

Our LS P7010C has an Iveco (Italian) engine. Pretty sure rest of the drivetrain is built/designed by LS. CT

I have a 9000 lb machine with a 24" and wouldn't attempt more than digging up a stump. CT

Same story here. Bought my tractor from dealer 30 miles away because he worked with me. The dealer I drive by everyday is 4 miles away. I have not bought ANYTHING from local dealer since 2014. CT

Not a Kubota. I bought a LS P7010C in 2014. 72HP, mechanical shuttle, mechanical direct injection turbo engine w/o any emissions. 750 hours without any major issues. It is heavy and has a very strong loader (+3500lb lift capacity). Filling tires is a requirement to use the loader at full...

I do my own maintenance. I just completed Tractor Fluid (15 gallons) and front axle (4 gallons) service on my LS P7010C. Also replaced both hydraulic filters, both engine air filters and cabin air filters. Was first time I had changed hydraulic oil filters. Found one of them had sucked in what...

I have seen purple on backup lights on RV before... CT

Still +8 years is impressive in my book! CT

Our P7010C was purchased in 2014. Still original G31 battery in it. It is spinning a little slower too. Impressed that it lasted this long! S Korean MFG battery. CT

I thought all LS came with a loader? CT

Yes. CT

Diesel CT

Hence why I jumped on my LS P7010C in 2014. Interim Tier 4. Mechanical DI, no emissions. CT

Why I bought our LS P7010C over other tractors of similar spec. Mechanical direct injection, turbo, muffler... Last of the Interim Tier 4 engines. Hope it is the last tractor I need. P7010C Engine Detail CT

I have no issues with my self leveling loader. I can scoop and carry a 100% full bucket. Bale spear not an issue. Would not buy a tractor without a self leveling loader with skid steer attachment. 2013 LS P7010C

Throwing my $0.02 in the hat. Leave everything intact. Disconnect GP load from relay. Wire this to another solenoid or relay with a momentary push button. OR Disconnect signal ground wire from GP relay. Use a momentary PB to ground relay coil. (Easiest IMHO) Both will work. CT

LS has a very nice, quiet cab. 2014 P7010C with 740 trouble free hours. Though 72 hp may be more than you need. CT

Not a Pete, 6x4, manual transmission... What else checks the OP's boxes with this truck? CT

I have one like, #1. Probably had it about 10 years. CT

Several years ago my father and I both bought new 60" grapples. Same grapple, made locally somewhere, no data tag. Skid steer attach, skid steer flat face couplers, twin cylinder grippers. They were at 2 different auctions in 2 different parishes (counties for the other 49 states). Paid about...

Finesse!

2014 P7010C about 700 hrs. Original battery. No issues yet. Looked at a P7040CPS? at an auction this spring. Had over 1000 hrs. Had a front axle problem... CT

Growing up on tractors without cabs or canopys was humbling. Have an open station Farmall 504. Bought a LS P7010C 7 years ago. Have had more than 1 time that bumblebees have swarmed cab while mowing. Bumblebees are bad news. The only negative of a cab is the initial purchase price difference...

I can honestly say the advantages of a cab far outweigh the disadvantages. They do require more care and upkeep. If you are the type of owner that just uses and abuses and doesn't believe in maintenance; then an open station is a better choice. A pole saw is a cab tractor owners friend. I grew...

Well I cannot use my P7010C yet, still very wet. I don't want to rut up the fields. So, I decided to replace the radio antenna that I managed to break off at about 6 hours on a tree limb. This is what was left of the OEM antenna. So I figured out how to open the roof to access the antenna...

Well, today I performed my 50hr service... Well part of it, at 58 hrs. Since its still so freaking wet I cannot bush hog, I figured I'll get ready for the new season to use my LS P7010C. Here is the oil change procedure. First you need a 12mm allen wrench or socket to get the drain plugs out...

Update: Operation Wood Rat Contacted dealer. Sent him some pictures. The "part" came in, he was as shocked as I was! This part, the low pressure injector return line was $537!:shocked: This was the only part of the assembly that was damaged. So I put my farming/maintenance...

Well its been a while since I posted last. I only used the P7010C a few times over the winter to blade (dirt and rock, not snow) the drive and move some brush around. I went to use it to blade a neighbors drive. I went to start it up to chill the cab down and smelled diesel... Hummmm...

Hello TBN. I have been a lurker for a long time. I used to spend most of my time on Yesterday's Tractor forum, as most of my equipment is, well Yesterday. BUT, since I have moved into current times, I will be contributing more often on TBN. I'm going to try and make this a "Living Document." I...

What size speakers are in the 2014 P7010C "New Style" cab? I have a feeling they are going to need upgraded to 2-way or 3-way speakers. Maybe even a small powered sub behind the seat. Nothing wild, just something to enjoy some Classic Rock with while tractoring. I have not really checked out the...

I have been going round and round for the past two weeks trying to get a deal going. I thought I wanted a XU5065CPS because of the hydro power shuttle. Instead the P7010C won out. I have listed some comparisons between the two that I observed. Your mileage may vary... I test drove a XU5065CPS...

Anyone priced these lately? Rhino SE8A looks like a nice machine, I have a Rhino 172. I know its tough. Bush Hog 2008 seems nice as well. Both would be lift type, pulled by a 65hp LS XU5065CPS or my Allis Chalmers 180. Thanks, CT

Hello guys, Any owners of the XU5065CPS (65hp) or P7010C (72hp)? I am awaiting delivery of a XU5065CPS to demo. I have already sampled the P7010C. Right now the XU5065CPS is favored because of the Power Shuttle and the P7010C for the 3 range PTO (540, 750, 1000). The P7010C is only $2500...

Guys, I have narrowed my new tractor purchase down to these two models. My dealer has a P7010C on the lot and has sold 5 of them in 4 weeks. He has only picked up one XU5065CPS and it sold the same day it was put out. Most of his sales volume is <40HP and >70HP so he doesn't stock many in that...

Brandi, You will be fine. My father has had his a little longer than me. He uses his on a Ford 6600 and MFWD JD 6430. See link TractorData.com John Deere 6430 tractor information He has not "Turned it into a pretzel yet! Though on the Ford 6600, he was doing something with a dead tree (trying...