Search results

Bought the Kibota L3302 with a backhoe, took delivery of the tractor late in the evening, didn’t get to play with it that day, the next day I went out to play around with it, be darn, the backhoe had leaked fluid on the ground over night. A brand new tractor less than 2 hours on it leaking...

Thinking about buying an MF1840, anything I should be aware of before I buy and find it out afterwards? Common Problems, typical behaviors, etc…

Dealer here doesn’t have an account with Woods, he says he’s trying but man I need one, anyone here a dealer and have one?

Got something going on with the front bucket, darn thing won’t stay at certain positions, it flops like a rag doll, I mean several inches of play. And I think digging in the dirt it has bent a boom or something.

So the CK 3510SE is nice but the rod for the bucket doesn’t have any level indicator mark at all, so I made one. Used a marker to mark level, used it for a while to make sure it was right, then I took and cut a shallow slot and added some bright red paint, now I have a point of reference of a...

Noticed the valve stem was on the inside of the front tire, dealers said he would change so it faced out, question is with a front end loader do they need to be the way they are For stability? Pain in the rear to check pressure! I’m coming from a CK20HST that the stems were facing out with a...

My headlight assembly is peeling in sheets of thin plastic. Not exposed to direct sunlight it is under a carport. Have never seen this before on anything, like mica (mineral) peeling. Any way to stop it? :confused:

CK20 HST Air -- Fram CA9248 Oil -- PH3593a Fuel -- 76KD-10331 Hydro (small) -- T2195-38031 Hydro (Large) -- T4260-38125 Please add if you know of other cross reference numbers CK20S Napa Part-----------Part No.-------Engine Air Filter------6449-----------CK20S w / Kioti 3C100LW (1.0L)...

Has anyone here done any sand casting? I am trying to cast a part from aluminum and want to learn how to sand cast, I have watched Youtube videos of it and it seems rather easily done. I have the sand mixed with the Bentonite clay (green sand), boxes made for the sand mold, just wondering if...

Was digging on tank yesterday and the joystick made a popping noise and flopped freely in my hand, the loader was stuck in down position so I could not make it out of the tank bottom. I remembered when I bought the tractor the kid showed me the pivots that he had to replace one because he broke...

Well got to do the first seasons mowing with the CK20 and the 60" Kioti branded finish mower. I noticed when mowing that the mower left strips of uncut sections, I thought well the blades are dull, since I bought the tractor used (430 hrs) I was guessing they had never been sharpened. So I took...

Well got the cart section finished for the air tank smoker grill, used the CK20 to set it on top of the cart section. Lucky everything was right and fit right on, yea! :thumbsup: Mobile hoist=CK20 Slowly but surely.

Something that annoyed me was the ROPS when not it full upright position was in a full flat position when in the down position, this would cause the mower to hit the ROPS and push it up. I tried several setting on the mower to try and stop it but nothing worked, annoyed me that I could not raise...

So looked out the front window yesterday and saw a Mesquite tree limb rather large one broken dipping down to the ground. Got out the Stihl and the CK20 and went to work. Limb looked green and had new shoots of leaves, no high winds the night before, but Mesquites are known for not being a tough...

I noticed the other day a drop of oil on the ground under the tractor, got to looking and saw a couple of more beads of oil coming from a inspection hole in the mid section (section between the motor and rear-end) of the tractor, anyone have a manual and can tell me what it might be leaking in...

Well cleared some more of the woods yesterday, man the little CK20 is great, a few trees did bog it down, but in the end the trees lost. :laughing: Noticed the right side bucket cylinder is starting to seep a little fluid, nothing major, I guess a cylinder repair is in the future now. :eek:

Going to use my CK20 to push up some brush tomorrow in the woods behind the house. The little bugger works great for that purpose. Since I got the part and did the Kioti repair to the FEL it does not flex any longer, makes a world of difference. Buying used sometimes can be a pain in the rear...

Just as the title says, I will be doing the same old thing. :)

Like the thread header says; (if lever is moved upward while engine is running it will make a clacking noise and will kill the engine.)

I noticed since I got the tractor that it intermittently puffs black smoke at idle or full throttle. Just a short puff but seems to happen quite regularly almost as if a injector is squirting more fuel every once in a while. I changed the fuel filter thinking maybe it was the problem but it...

Where is the "air vent cock" on a CK20 injector pump? Manual says to open after filter change, I cleaned the filter, which was dirty, and am going to replace but confused as the manual states after filter change to open "air vent cock" on injector pump, run engine for 30 seconds, have looked but...

I know this has been discussed at length at some point or another, but I was wondering what to do with a used CK20 that has the problem, the previous owner neglected to have it repaired. I did not know exactly where to look before I purchased the tractor and did not notice until I was doing the...

I found a CK25 for a good price and was wondering about the Injector Pump problem and FEL cracking, it is a 2006 year model, don't know serial number. Is there a serial number range that should be looked out for, if so range number? Also found a Cub Cadet in the same range Yanmar EX3200, better...

What is a fair price for a 800hr 99 JD 855 tractor? 7,8,9 K? And what size is the darn thing, on the internet they look rather small, but the picture the guy has looks like the thing is a mid sized tractor (person selling says rear wheels are 4 1/2 feet tall), does that sound right? Thanks

Noticed a leak in the fuel line on the tractor near where I had installed a cheap in-line petcock (plastic) , the L2800s don't have a fuel cut off , so made it by a local motorcycle shop and grabbed a real petcock (brass) . After installing and cleaning the area drove the tractor around , moving...

So what does the Assy Valve Safety on the 3 point housing of a L2800/3400 do ? Can it be used to lower hydraulic pressure to LCV ? Is there a way to lower pressure to the LCV and not affect the FEL pressure ?

Don't remember if the tractor (L2800 with updated valve) did this before now but when I let the box blade down to the ground at say 4 on the lever scale I have to move the lever to 6 or more on the scale before the blade starts to lift , shouldn't the 3 point raise at or about the same point the...

I have come up with kit that will allow anyone to add a tool box behind the seat of a L2800-3400 Kubota tractor . 3 pieces uses existing 3 point top bar hanger and Slow Moving Vehicle sign , Kubota Orange , bolts right up just add box . PM me if interested .

Well talked to someone from Kubota today about the 3 point shudder problem , the guy said where did you hear about the fix from . I told him I seen it on Tractorbynet.com , he said in a sarcastic way , "What a place to be getting information from" . So now he tells me that Kubota is calling it a...