Search results

What is the specification for the Iseki TA270F (engine# E3AD1, injector# 6215-300-004-10) fuel injector pop pressure? The local diesel injector shop has closed, so I am planning to build a pop tester to check my Iseki and Yamar injectors. I suspect that it is a Zexel injector, but I am not...

I am looking at replacing my Mitsubishi MT2201D and Yanmar YM1510D, but it does not look like folks are importing grey market tractors. Given the recent improvements in the Yen exchange rate, it seems like there would be more inventory available. Does anyone have any insight of the current...

I stripped my Iseki TA270F tractor down this week and put on a fresh coat of paint. The only trouble, my fuel tank has several holes rusted through from the inside out. The bubbles of paint on the bottom of the tank were the only thing holding the fuel in the tank. Does anyone know if the...

Parts, Operation, and Service manuals, Item number: 7568074409

I thought some folks might be interested in my inexpensive turf tires. I installed 4.80-12 trailer tires ($18 each) on the front wheels, and 285/75R16 truck tires ($25 used pair) on modified rear wheels (drilled new bolt pattern). All the diameters are the same as the original tires, and I...

Has anyone instsalled a Koyker 110/120 loader on a TS1610F using the TS1610 (2WD) mount kit? I do not see any reason it would not fit, but Koyker has not tried the 4WD version, probably because it is uncommon.

I replaced the bearing in my JD317 PTO clutch, but I do not know how to reassemble it correctly. The 4 outer bolts tighten down on the plate with 4 springs backing it. How do you know how much to compress the springs?

I am looking for the 1610 parts manual page for the fuel pump assembly. I am trying to determine if the 1510 pump that came with the 1610 it is compatiable... Thanks.

The fuel injector pumps have a plate with two numbers, what do they mean? YM1510 - 3T72SA, 8A715 YM1610D - 3T72SA, can not read 2nd number w/o removal How would the 1610 fuel pump deliver more fuel than the 1510 fuel pump? Are the shims on the plungers different, the cam in the engines...

I broke the threaded end of my throttle control cable sheath on my tractor. Does someone know where I can order a new sheath for a specific length, or perhaps a universal kit of sorts to build a custom cable?

What is the fuel filter number for a F22D?

Does anyone know of a source for rubber cap oil seals. This particular one is a NOK 62 10. My local bearing and seal dealers look at me funny when I bring one of these to them for replacement.

Does anyone know a US temperature sensor part number to fit an MT2201D or perhaps another Mitsubishi tractor from the mid 80's?

What oil filter and fuel filter fits the MT2201D?

I am looking at an F24D with a cracked engine block that has been repaired by the dealer in Japan. Is this a worthwhile investment, or will the engine likely have a short lifespan? What would be a reasonable difference for the price as compared to one without the engine damage?

A little off topic, but my neighbor had a contractor extend the exterior walls of the house for three rooms. The bonehead poured the concrete as much as 1.5" higher than the existing concrete slab, and then quit the job. The addition is now under roof and they are planning to install hardwood...

48\" Mid Mount Mower Source What are some brands of mid mount mowers to look at for a YM1510? I am interested in about a 48" mower deck. It looks like Woods only has a 42" and a 60". 60" is too wide for the slopes on my yard....

I have about 5,000 sqft of woods that was a farmer's field about 40 years ago. The top two feet of soil is topsoil mixed with years of decaying leaves, and underneath is subsoil clay that is supposedly about 25' deep. I have thinned the trees greatly and continue to do so with hopes of...

Does anyone know if any MF tractors have the Toyosha engine BD143 (1.4 liter, 3 cylinder, about 25 HP)? I am trying to find a tach drive for my 1989 Hinomoto tractor (N209).

Here is a picture of my new 3 point trailer hitch attached 4' rake. It was a simple project (with welder, drill press, and chop saw), and I only spent $30 at TSC to buy the tines and bolts. The rest is scrap metal. It did a great job of pulling up the old grass clippings to expose the soil...

Does anyone know of an air filter assembly at a reasonable cost to fit an Iseki TS1610F. The Surplus Center has one for $30, but it is too big. I am having trouble locating the air filter element, and I am not willing to pay $80 at the tractor dealer.

I have a fork lift propane tank that I would like to setup for my propane/oxygen torch. The tanks on fork lifts are mounted side ways. Is there a special pick up tube or do the fork lifts draw liquid propane from the tank? If I set the tank upright, will I be able to draw propane gas instead...

My 1610F has separate hydraulic and transmission oil compartments. Should I use Hy-tran for the hydraulics and 90W gear oil for the transmission?

I bought a TS1610F that is arriving in about a month. What are the filter numbers for the air, fuel, oil, and any other filters that I might need? Does this tractor use hytran for the transmission and hydraulics or are they separate? Is the Bolens G194 operator's manual the closest English...

I just installed a FEL and backhoe on my N209. The hydraulic fluid seems to be running very hot. The backhoe and FEL valves are very hot to the touch. You can hold you finger on them for a few seconds at most. How hot is normal? Is this generally a valve issue or some other restriction in...

Does the YM2500 have a 3 digit or 4 digit hour meter (not including right of the decimal point)?

How similar is a C174 to a C144? Are they the same minus the wheel size and HP? Is either similar to a MF1010?

I finally got my N209, and it appears to be in pristine condition minus the tail light that was broken off in the container. The front axle seals will need to be replaced soon, but the oil was fine. I am trying to figure out the "Shuttle Shift" as written in English on the back of the tractor...

What is a good source to purchase the boots to cover the power steering hydraulics and ball joints on a Hinomoto E2004/E2304?

Does the MTE2000D have a synchronized transmission?

Is any familar with the Hinomoto N209? I am debating importing an N209 that looks like it is in really good condition. Are there any similar US models? Are the parts similar to the E2004/E2304, especially for the engine and drivetrain?

How much has the Japanese Yen increased in American dollars over the past year? Are other exporters charging more for tractors because of the Yen's strength the past year?

I bought a Barnes 12 VDC hydraulic power unit with power up and gravity down (I belive it is a GC8000) on Ebay. Unfortunately it did not come with directions. I rotated the pump 90 degrees, and I adjusted the oil pick up line 90 degrees to match the new orientation. I installed the pump on my...

What years and/or models did Massey Ferguson switch from Hinomoto to Iseki?

Are any of the newer (since 1985) models of grey market Mitsubishi tractors identical or very similar to a US model tractor? If so, which ones? Keith

Are drill bit sharpeners worth the money? I drill a lot of holes in steel, and I wear out a lot of drill bits. If I resharpen the drill bits, will they still perform well for drilling steel? Or will the hardness of the drill bit be ruined (or perhaps is already ruined) and then not stay...

I have a Hinomoto tractor with a narrow ring of pitting on a very expensive bearing where it contacts the king pin seal. I would like to repair the pitting, and I am considering using JB Weld or Plastic Steel to fill the pitting, and then machine the bearing back to its original dimension...

Should the bottom pins on the FEL bucket be loose? I just bought a Hinomoto with a quick detach FEL, and I can see where the holes have been opened up from use, but they appear to originally have been larger than the pins. I took a look at a John Deere FEL with a quick detach bucket, and those...

I am looking for a cross reference for a temperature sensor on an E2004. It is the temp sensor on the left for the temp gauge. It should be same as the 2304 and perhaps an MF1030.

I have an E2004 with a FEL. I am planning to build wheel weights and/or a utility/weight box for the three point hitch. How much weight should I plan to use for each location?

I am rebuilding the front axle on a Hinomoto E2004 that is full of wet sludge on one side, and full of dry caked sluge on the other side. Where did that mud like substance come from? I find it hard to believe that much mud got past the seals, and I have found no evidence of corrosion inside...

My 1510D is stuck in 4WD. I suspect it is the pin on the 4WD lever that moves the slider to engage the shaft to the front end. Is there any hope of fixing this without splitting the tractor? Any suggestions? Keith

According to the specifications at http://www1.sphere.ne.jp/delmundo, I found the following size and weight specifications: E2004 250Lx121Wx185H cm 1007 kg E2304 253Lx122Wx187H cm 1024 kg I would venture to guess that the difference in these tractors (3L x 1W x 2H cm and 37 lbs.) is the size...

Would the models like, F255 and F145, be the same as the other F series Yanmars, but in a half horsepower increment? I have not seen the specifications or discussions for these tractors posted, I am curious if they are common and if they have the same parts availability as the other F series...

My 1510D has a 20" spread on the 3 point hitch for the aftermarket lower arms. If I move up to a 16XX, 17XX, or 18XX, would I still have the same spread on the lower arms, or would it increase to 26"? Also, I am making a FEL for my 1510D, and ultimately, I would like to move up to one of the...

What would be the minimum reasonable size Yanmar to run a heavy 6' bush hog and a 6' finish mower? Keith

How do hydraulic systems without power beyond (closed center system) work? I am plumbing my 1510D for a FEL with a power beyond valve. I have since spotted a small inexpensive Bradco hoe for sale. It only has two hydraulic connection hoses, so I am expecting it is a closed center system. Can...

I finally received my 1510D from a group buy direct from Japan. The tractor looks and runs great with the exception of a bad voltage regulator, and I still need to test the 4wd. I am building a FEL, and I am looking for advice on plumbing the hydraulics. I plan to splice into the high...

Does anyone know a cross reference for the hydraulic filter on a 1510D? The 186D parts catalog lists the Yanmar filter number 194464-48310.