Search results

Yeah, I did a lot of ICF research, and I love the concept. Unfortunately, just don't have the budget for it. In a perfect world, that's probably what I would use as well.

Thanks, I'll look into it! I probably wasn't so clear in my wording, but I do plan to go vertical with the GPS on the foundation as well, so the slab is isolated, same on the walk-out.

Hey Rusty, yes, that is the current plan. GPS is just EPS with infused graphite (usually referred to as Neopor), increases the R value substantially. Thanks for responding! This new format is kinda wonky...

Bump. Traffic here sure isn't what it used to be! :(

Wow, been off line for a few weeks, looks a lot different around here! :unsure: Hopefully some of you knowledgeable folks with construction experience are still around... So, I've been planning a log cabin build for several years now, and I'm finally pretty well set with log supplier, builder...

I've had a couple inquiries, no offers. I'm not exactly pushing it, either....just passive info on a couple forums. I'll most likely stand pat, as my "want" doesn't justify the current cost differential. Current KB incentives expire in June I believe, so I may revisit after that, just to see...

Thanks for the input gentlemen, this is purely a want more than a need, and something I would opt to do only if the numbers are advantageous for all involved. I was offered $10K on trade for a B, and thought I could do a little better with a private sale. We'll see.... If I had found what I am...

Thinking about upgrading to a B, so testing the waters for my BX2380. It's a '17 model, 79 hours, and yes, pretty much like new. Includes quick-tach FEL, R4's, Woods RM48 RFM, BXPanded under shield, BXPanded quick-on bucket hooks (2), and Hodge telescopic stabilizers. Garage kept, used for...

Looking on Amazon, all the choices are rather overwhelming! Anyone with a positive experience worth sharing? Just looking for extra support for my lower back when working, to help avoid some of the pain that comes after a day of working/lifting/etc..

Doing some mower maintenance the other day, and the thought randomly popped into my head....does blade clocking make any difference in cut quality? Specifically to a three blade finish mower. I typically don't set them to any position, just randomly tighten them in place, where they happen to...

I'm several years away (5'ish?) from a retirement cabin project, been looking at various building methods. In a perfect world, I'd just do a small (~1K f2, one story w/ walk-out basement on a hillside) log cabin, but then I start thinking about maintenance, battling the critters, etc.. Not sure...

preparing for the inevitable here... the replacement of our 28 year old HVAC system. Looking for recommendations on good new systems. Current setup is a 1991 Ruud UGNG gas furnace w/central air, sized for a 1700 ft2 house. It's been very reliable up until the last few years, requiring some...

My summer project at the camp will be a small 8'x12' free standing deck. Looking for guidance on support structure. Right now, the plan is to use concrete deck blocks setting on grade. Is there something better/easier? How many should I use? Should I stay on 16" centers, or is 24" OK...

I think it would be handy to mount a 12V dry spreader on the FEL of my BX, mostly for yard fertilizing. I've looked into a few, thinking the ATV type would probably adapt the best to the FEL. The problem I'm finding it locating a reasonably priced spreader that has 12V gate control. Most of...

Looking for opinions/experiences with exterior siding, based on the following: In an effort to, A) reduce maintenance on tall ladders, and B) improve my homes looks & curb appeal; I'm considering a siding change on the upper gable half of the north side of my house. It's currently all cedar...

Agree with this 100%. Had a Kawasaki that had the same issue.....you'd swear it was a fuel problem, but no, it was coil packs also.

Anyone have any experience with these, opinions, comments, etc... I want to redo my current portable generator back-up system for my house. I'll be getting rid of a my 6 gang 15A transfer switch, so I can get more capacity. Thinking of going the interlock switch route vs. buying a bigger...

Agree with 3930dave, invest in a quality aluminum trailer first, as you will likely have that the rest of your life. Then, upgrade the truck & toys as budget allows. This is my R&R (from Michigan), 18' tandem, weighs 1400#'s empty. The Ridgeline is a decent tow vehicle when kept close to it's...

The EB's are fantastic tow engines, and the new 10AT makes them even better. Always so relaxed, and never lacking for power. And with low aero drag, are amazingly efficient. Here's a recent trip taking my tractor down to my camp in SE Ohio hill country. Trailer load was about 4500#, another...

Got about 4" of snow yesterday, so of course I HAD to get the BX out to clear the driveway.....no way my F150 would make it out with 4" on the ground! :laughing: Good chance to play, actually, and use my urethane snow edge I put on the FEL. I must say, once again, the little BX was a pleasure...

Considering adding a 1"x4"x48" urethane (UHMW) strip to the bottom lip of my FEL bucket, for snow clearing on my blacktop drive. Wondering if anyone has done this, and the results they have experienced? They are pricey at ~$100, so wondering if this is my best option.

Oops! Just realized you already test drove. Sooooooo, never mind. ( I hope you didn't just putt around the parking lot...)

Mustang all the way! The most engauging driver of the 3, which you'll realize if you test drive all 3. Many ways to configure the exact model to suit your tastes. Go as wild or mild as you wish. Go test drive and prove it to yourself. ;-)

Congrat's on the new machine! A BX2380 followed me home this week, too! Too darn cute to shoo it away...

Great write-up frugalangler! I went through a very similar process to find a SCUT to fit my needs, ended up with a KB BX2380, just took delivery this week. (pic below) My short list was the KB, JD 1023E, and LS MT125. Not respective of price, the KB was my fav, but quotes were coming in really...

Sorry dnm, I missed this thread somehow. I bought from Green & Son, they have a store in Mt Sterling & Hilliard. I went through the Mt Sterling store. If you call, ask for Steve. Super nice guy, beat everyone else's price by quite a bit. Just brought it home today, here's a pic. Love it so far!

Well, here she is! Brought her home today, and put it to work. Really loving it so far!

Dealer quoted $14,999 b/f tax, new 2017 1025R with FEL. Seems like a pretty fair price. Opinions? Currently, the Kubota BX2380 is my 1st choice, but the JD price has me thinking.... ($500 more than the Kubota)

Trying to decide which would be a better choice. Advantage I see with the finish mower, I can also get my son to help mow our "good" yard, along with me on the ZTR. Can't do that with a rotary. I think it will also work for the "rough" mowing, as it's really not that rough, just taller, stringy...

Hello all, new member here! Looking at a new 2017 Kubota BX2380 w/FEL (pinned, not quick-mount), dealer is quoting $14225 before tax. Looks like discounts of about $1000 from MSRP, based on what I can see from the Kubota website. Is this about the norm for Kubota products? I really like the...