Plowing heavy snow yesterday I heard a bang and the right rear tire seized. It will move a little. I'm hoping it's a brake problem...
Any advice before I dig into it appreciated.
I adjusted my valves 300 hours ago. When I did the radiator was out and it was easy to put a wrench on the crank. Is there an easy way to turn it over without taking the radiator out? Thanks
I’ve been searching for info on power steering repairs for my ym276. Found some great threads and would like to “bookmark” them. Any ways to do it in TBN?
There's an inch of play in my PS link. There's a zerk but nothing like a boot. Have I lost a part? Steers fine.
Thanks to everyone who posts to this site.
It might be time to stop climbing to clean my chimney. I've seen adds for a chimney cleaning tool with something like a weed wacker head on a flexible rod driven by a drill. Has anyone used one? I'll have to go in through the chimney thimble into an 8x10 flue and up about twenty feet. Thanks for...
My ym276 charge light has flickered for a month. Now it's on at working speeds all the time but off at low rpms. Too cold to tinker right now so I put a charger on it if I have to. Any suggestions on what to look at first when it gets warm again? I did tighten the belt a bit but no luck.
Bought a new loader valve with a third spool to run a grapple or a snow plow. The tech guy I talked to recommended removing the third spool handle to avoid deadheading when no tool was attached. What's the difference between deadheading and moving a piston to the max? Thanks in advance.
Time to change my YM 276 trans fluid (300 hrs). Hate to throw it away. Can I use it in my Didier wood splitter? Splitter has a four or five gallon tank and have no idea how old that fluid is.
Thanks
I've got a 276 D with a 1075 loader. Looking for info on the valve. The only marking I can find says Kontak. Like to find a schematic. Any info will help.
Have a Yanmar 276 D and bucket with tooth bar. I want to add a bolt on grapple. Could someone steer me towards information on plumbing this set up?
Thanks
6' 3ph Meteor Force king model # SB75EC is available in my neighborhood for $1000. The machine has 25 hp at the pto. Is it to big? I'll run it on a gravel driveway and down a rough dirt road.
Thanks
This old splitter was way to low so I built a 2x4 and plywood stand for it. I'm working at waste level now. The loader does all the lifting. My back loves it.
Hello,
I've just signed up for a free month of Hughesnet satelite internet and I'd like to figure out if my usage will exceed the monthly quota. The system has been in for about five days. My wife works online from home and we've streamed a movie. We've been online at least 24 hours already but...
My 276D is set up for snow plowing. Two storms ago after about 5 minutes of warm up I'm in reverse and the machine stops - like I backed into a tree (no tree). Restarted and all worked well. This weekend it happened again after about the same amount of warm up time. I guess I got the clutch in...
I'm looking into buying an umbrella homeowners policy. The application questionnaire asks if I have a pool. There is a 100 year old cistern down in the woods that was a water supply for a mine. I've got it posted and fenced with wire and plastic mesh but the fence is mostly a warning to hunters...
I know distances and directions from two pins that converge on a missing point. The terrain is to rough to pull a tape and I'd like to mark along the lines. Seems like a good GPS might solve my problem. Any how-to advice or on affordable systems or places to rent? Thanks in advance.
Removed the leaking seal from my TB tine shaft. There's a pretty good groove in the shaft. Some one posted earlier about solving this problem with a Speedi-Sleeve. Does anyone know where I can buy them? The seal ID is 1 1/4". Can I order the new sleeve using that measurement? Any information and...
I've had this YM 276D three years and love it.
I replaced the hoses when I got it and left them as is (see pic) because I didn't want to risk taking things apart to much. I think I'm bypassing the thermostat. Changed the oil yesterday after an hour of moving firewood. The oil was warm but not...
I think it happened when my cat walked across my key board. The type face on my PC got very small. Luckily it's still OK on my work machine. Help appreciated.
The alternator light on my YM276D flickers intermittently. It might be heat related. It starts after 15 minutes of run time. The flicker goes out when I turn the work lights on. The light comes on full red for 10 seconds when I turn the work lights off and then starts to flicker again. Any ideas...
Here are some pics of wooden tractor modifications. Bucket forks, chainsaw and chain racks and a cant hook holder. So far everything is working as required. Scrap 2x4, 3/4" plywood, construction adhesive and drywall screws - cheap.
Just bought an old splitter. The owner had the manual. It calls for 10-30 motor oil for the hydraulic fluid. Is this a good choice? Is there a better choice?
Thanks
It was 16' yesterday morning. Machine started fine but the fel control valve was stuck. The guy I bought it from said this would happen and then thaw after 15 minutes of idling. Sure enough it did. Any advice on correcting the problem would be appreciated.
1. Where can I get a YM 1075 FEL manual or will someone sell me a photo copy or scan of theirs?
2. Where can I get a new boot for the control valve (Kontac)?
3. The bucket dumps when I push the joy stick to the right. Brother in law thinks the lines are crossed. Have plenty of bad habits...
The upper hose on my 276D (3T84HA) engine has a shunt that returns to the block by the sender unit. Hoye Tractor has never seen this before. Believe I've seen a drawing of this arrangement in a parts book but of course can't remember where. Any help appreciated. Please see attached photo.
I'd like to swap my turf tires/wheels for ag/tires wheels. Does anyone know a source? Is there a twin Deere model for the 276 D that might provide these parts? Or should I just buy chains? Can anyone recommend a Yanmar dealer in Massachusetts or surrounding states? Thanks for any information.
I'd like to swap my turf tires/wheels for ag/tires wheels. Does anyone know a source? Is there a twin Deere model for the 276 D that might provide these parts? Or should I just buy chains? Can anyone recommend a Yanmar dealer in Massachusetts or surrounding states? Thanks for any information.