Rustyiron
Super Member
"Get western"? I like it, is that like "go crazy" or something?
track too tight
- Thread starter percy c
- Start date
- Views: 15756
"Get western"? I like it, is that like "go crazy" or something?
Jim Nelson
Platinum Member
If your tracks are real dirty they will bind up,I've also had it happen in deep snow.
DJ54
Elite Member
- Joined
- Jan 20, 2009
- Messages
- 4,616
- Location
- Carroll, Ohio
- Tractor
- IH Farmall 656 gas/ IH 240 Utility/ 2, Super C Farmalls/ 2, Farmall A's/ Farmall BN/McCormick-Deering OS-6/McCormick-Deering O-4/ '36 Farmall F-12/ 480 Case hoe. '65 Ford 2000 3 cyl., 4 spd. w/3 spd Aux. Trans
Comes to mind, it takes about a 3/4" wrench to fit that check valve. If you have a 6-way blade. you can put a suitable block (6 X6 or so) between the back of the blade, and idler, angle left, and push it back.
Billrog
Veteran Member
- Joined
- Dec 9, 2014
- Messages
- 2,056
- Location
- Armstrong, British Columbia
- Tractor
- Kioti 2610, 580 SuperM Case Backhoe
Percy all what I did in the past finally remembered was stick a piece of 6x6 or something in front of the track to drive against to push it back.
rustyshakelford
Veteran Member
Put a 4x4 between the front of the track and back of he blade. Turn the blade in slow. It'll collapse the tension cylinder and push all the old grease out.
Brett
Brett
Billrog
Veteran Member
- Joined
- Dec 9, 2014
- Messages
- 2,056
- Location
- Armstrong, British Columbia
- Tractor
- Kioti 2610, 580 SuperM Case Backhoe
Good idea Brett we didn't have 6 way blades when I had to do it this would be much simpler :thumbsup:
herringchoker
Platinum Member
What Gordon says.
On my 450, the zerk threads into a check ball assembly. Yours is probably the same. Here's what my manual says to loosen the track:
"Loosen, but do not remove the adapter into which the pressure fitting (zerk) is inserted. Allow enough grease to run out until the proper track sag is reached. Tighten the adapter to 45-55 ft.-lbs. torque."
Like Gordon says, you may have to push on the front idler to get the adjuster to collapse.
Good luck with it.
On my 450, the zerk threads into a check ball assembly. Yours is probably the same. Here's what my manual says to loosen the track:
"Loosen, but do not remove the adapter into which the pressure fitting (zerk) is inserted. Allow enough grease to run out until the proper track sag is reached. Tighten the adapter to 45-55 ft.-lbs. torque."
Like Gordon says, you may have to push on the front idler to get the adjuster to collapse.
Good luck with it.
Citydude
Super Member
Yep, Get Western means treat the clutches like you stole it....I'm a former operator. You can tell I'm not a mechanic.....
Dozernut
Veteran Member
- Joined
- Apr 6, 2002
- Messages
- 1,611
- Location
- South Eastern Illinois
- Tractor
- ZD1211, RTV900, LX2610SU and a SVL65 CTL
If you don't have a 6-way blade, hook a come-along to the idler wheel and chain it to a rear frame member. Be sure that side is off the ground and supported with wood blocking, not concrete, concrete will crumble with the weight. Crank it back and the grease will come out. To push it back reinsert the zerk and pump it into position with a grease gun.
firemanmike69
Silver Member
Another way to help loosen track tension after you take the check loose is to back up with a piece of firewood between the track and the sprocket just take it slow