TODAYS SEAT TIME
- Thread starter LBrown59
- Start date
- Views: 2859583
Slowpoke Slim
Elite Member
- Joined
- Jan 6, 2017
- Messages
- 3,629
- Location
- Bismarck, ND
- Tractor
- Husqvarna YTH24V48 riding mower, Branson 3725CH
Looks like a Nova to me.
Mooseman1616
New member
- Joined
- Jul 7, 2021
- Messages
- 23
- Tractor
- Yanmar 226D
is this a homemade fork set-up? I really like the execution. Can you post some other shots of it?
walker450
Platinum Member
Here is my thread, be sure to go all the way to the last few posts because I had to redesign them and that's what I am still using to this day. I'll try and do another video about them.
www.tractorbynet.com
Brush Forks for 23HP Kubota BX2350
I purchased the material for $45 and welder these up a few days ago. Some of the pics were taken before I welded the vertical pieces that allow it to be bolted to the bucket. I used a hole that was pre-drilled from the factory in the bucket. These work very well. I only wish I had made them...
www.tractorbynet.com
Gordon Gould
Super Member
- Joined
- Apr 1, 2007
- Messages
- 6,659
- Location
- NorthEastern, VT
- Tractor
- Kubota L3010DT, Kubota M5640SUD, Dresser TD7G Dozer
Yes of course you should know!!
'72 Nova
Thanks - your absolutely right I should. Actually I did know but it is hard to recall things I know. Drives me batty. Someday you will understand.
gg
4shorts
Elite Member
Really? I know this is an old post but I’m really surprised at your comments. If you removed the money from YouTube there would only be about ten channels Left. That said I guess you do your job for charity. Your didnt seem to mind me doing a video on your Click Bond did you?
We haven’t made a video in over four months and yes when we have we let people know about our products and I bet you watched ever friggen one of them.
In four years we’ve gone through two major expansions, added thousands in new tooling and haven’t had a week off in five years.
As for why I don’t spend any time on the forums anymore. We’ll time is a major factor and when I was here showing members my work and ideas a few went off and did them and never had the decency to even gave me credit for the idea. I bet you remember you were included in that and then you come on here back biting me. Great guy.
Last edited:
Sawyer Rob
Super Member
Here's some "seat time" for you. I normally re-shape my back garden every year and this year was no different,
With that done, I leveled it out,
AND it was then, ready to plant,
SR
With that done, I leveled it out,
AND it was then, ready to plant,
SR
Gordon Gould
Super Member
- Joined
- Apr 1, 2007
- Messages
- 6,659
- Location
- NorthEastern, VT
- Tractor
- Kubota L3010DT, Kubota M5640SUD, Dresser TD7G Dozer
What are you going to grow in that patch SR ?
I did the 1200 hr maintenance on the M5640 which included transmission oil/filter and front axle oil changes. Iv'e put this on before, 600 operating hrs ago I guess, but this is how I handle 42 Quarts of transmission oil. Put 3 buckets down over the bank and run a pipe from the drain pan to them.
I use a rattle syphon to refill the new oil. It's a lot slower then fuel which goes pretty quick. The hydraulic oil takes a little over 20 minutes for 5 gallons but there is lots of other stuff to be doing while that happens. And, I don't spill any or have to mess with getting a funnel into an impossible place.
I have a geared transmission and I run run Rotella HD in it. I use SAE 80-90 gear oil in the front axle.
gg
I did the 1200 hr maintenance on the M5640 which included transmission oil/filter and front axle oil changes. Iv'e put this on before, 600 operating hrs ago I guess, but this is how I handle 42 Quarts of transmission oil. Put 3 buckets down over the bank and run a pipe from the drain pan to them.
I use a rattle syphon to refill the new oil. It's a lot slower then fuel which goes pretty quick. The hydraulic oil takes a little over 20 minutes for 5 gallons but there is lots of other stuff to be doing while that happens. And, I don't spill any or have to mess with getting a funnel into an impossible place.
I have a geared transmission and I run run Rotella HD in it. I use SAE 80-90 gear oil in the front axle.
gg
