Traction Steering wheel alignment

   / Steering wheel alignment #11  
Mmm, this thread got me thinking,

Just a question, what happens on fully hydrostatic steering if the engine dies while descending a hill with turns?
Will the orbital valve still provide hydraulic pressure to the ram and therefore wheels If you turn the steering wheel ?

If not, that would seem to be a small (safety feature) of mechanical steering with hydraulic assistance versus Full hydrostatic steering.

It will still allow you to have a fully controllable steering. Although it will be very very hard to turn the steering wheel.

The orbitrol steering valve is equipped with check valves that allow the operator to steer even without the engine running.
 
   / Steering wheel alignment #12  
Mmm, this thread got me thinking,

Just a question, what happens on fully hydrostatic steering if the engine dies while descending a hill with turns?
Will the orbital valve still provide hydraulic pressure to the ram and therefore wheels If you turn the steering wheel ?

Hmmmm....don't do that.:eek:
 
   / Steering wheel alignment
  • Thread Starter
#13  
I tried turning the wheel without the tractor running and it will still move the tires so would guess you would have some steering but probably be interesting.
 
   / Steering wheel alignment #14  
I tried turning the wheel without the tractor running and it will still move the tires so would guess you would have some steering but probably be interesting.

It would steer easier if the tractor was in motion..
 
   / Steering wheel alignment #15  
Don't think so much about your knob position and you will probably get use to it.

Agreed. The more you use it the less you think about it. If you aren't sure if you like it take it off and see if you miss it. I know I would.....
 
   / Steering wheel alignment #16  
One our Texas members installed 3 spinners on his Kubota so one was always handy!
 
   / Steering wheel alignment #17  
agreed, my 45 year tractor is like that

Zebrafive
My I ask what 45 yr old tractor you're referring to? Surely not your 2030 that has mechanical linkage for steering?
 
   / Steering wheel alignment
  • Thread Starter
#18  
Been a few weeks since I posted this but am going to leave the spinner on. It is just to handy to give up. I especially like it when running the RC and backing in around things. Getting used to the idea that it is not always in the same location and don't think about it at this point.
 
   / Steering wheel alignment #19  
When my eyes and right hand are busy, the thumb on my left hand circles the steering wheel until it finds the spinner. It has been doing it that way for a looong time.
 
   / Steering wheel alignment #20  
Recently got a spinner for my steering wheel as I have had one in the past and found it handy.

Put it on today and mowed a couple of hours with the RC. The surprising part to me is on this Kubota the steering wheel does not always return to the same spot. Is that normal?

I put the spinner on at about the 10:00 position withwheels straight.

Sometimes it would be there when going straight but more often than not it would end up at some random position. Never had that happen before on anything else.

Kind of makes the spinner a pain and will probably take it off.

Will happen all the time if steering is on a hydraulic circuit.
 

Tractor & Equipment Auctions

2015 Ford Transit 250 Cargo Van (A50323)
2015 Ford Transit...
Payment Terms (MUST READ) (A50774)
Payment Terms...
2000 OSHKOSH MILITARY M1070 TRUCK (A51243)
2000 OSHKOSH...
1987 LANDALL 48ft Hydraulic Slide Axle T/A Drop Deck Trailer (A51692)
1987 LANDALL 48ft...
2016 Hino 258 Roll Back (A52384)
2016 Hino 258 Roll...
2014 John Deere 700K LGP Dozer (RIDE AND DRIVE) (A50774)
2014 John Deere...
 
Top